Enviro EF-IV I technical manual Horizontal Exhaust Through the Wall

Page 19

HORIZONTAL EXHAUST THROUGH THE WALL

1.Choose a location for your stove that meets the requirements stated in this manual and allows installation with the least amount of interference to house framing, plumbing, wiring, etc.

2.Install a non-combustible hearth pad (where necessary).

3.Place the appliance 15” (37.5 cm) away from the wall. If the stove is to be set on a hearth pad, set the unit on it.

4.Locate the center of the exhaust pipe on the stove. Extend that line to the wall. Once you have located the center point on the wall, use a hole saw to cut a 7” (175 mm) diameter hole for a 3” (76 mm) vent pipe or an 8” (200 mm) hole for a 4” (101 mm) vent pipe.

5.Install the wall thimble as per the instructions written on the thimble.

6.Install a length of 3” (76 mm) or 4” (101 mm) vent pipe into the wall thimble. The pipe should install easily into the thimble.

7.Install the fresh air intake (SEE PAGE 23)

8.Connect the exhaust vent pipe to the exhaust pipe on the stove. Seal the connection with high temperature silicone

9.Push the stove straight back, leaving a minimum of 2” (5 cm) clearance from the back of the stove to the wall. Seal the vent pipe to the thimble with high temperature silicone.

10.The pipe must extend at least 12’ (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble.

11.Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees, plants, etc. within several feet, a 45-degree elbow can be used as termination. The elbow must be turned down to prevent rain from entering.

5 5/8”

10 3/16”

715/16”

 

Note: Some horizontal, through the wall installations may require a “T” and 4-5 feet (122 to 152 cm) of vertical pipe outside the building to help the stove draft properly. This may be required if a proper burn cannot be maintained, after the stove has been tested and the airflow set. This is due to backpressure in the exhaust, caused by the airflow around the house.

15 1/8”

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents EF-IV Operation Envirofire Installation ManualUSE of Cordwood is Prohibited by LAW Important Safety DataI. Pellet Standards Pellet Quality is IMPORTANT, Please Read FollowingAutomatic Safety Features of Your Pellet Stove Turning Your Pellet Stove OFF HOW to Start and Operate Your Pellet ApplianceClip on Door Installation SLIDER/DAMPER Installation InstructionsSpecial Notes Freestanding ASH PAN # 1 see Areas for Routine InspectionASH PAN and Door Gaskets Burn POT Liner Igniter Tube Fresh AIR Insert ASH RemovalInstallation of fire box backing Electrical Component Functions Auger Motor and Auger START-UP Timer11 F 93C Manual Reset Temperature Sensor EXHAUST/COMBUSTION BlowerVacuum Switch 12 F 71C Temperature Sensor13 F 49C N/O Temperature Sensor SHUT-DOWN Sensor 14 F 49C N/C Temperature Sensor Ignitor Shut Down SensorVent Termination Requirements Deciding Where to Locate Your Pellet ApplianceRemoving Your NEW Stove from IT’S Pallet Fireplace DimensionsClearance to Combustibles Masonry Fireplace Insert INSTALLATION, Model FPIAssembling the Face Plate for the FPI Model FPI Pedestal InstallationStandard 40 X 27 7/8 Clearance to Combustibles Freestanding INSTALLATION, Model FSAssembly Freestanding Pedestal InstallationInstall Four Screws Here Horizontal Exhaust Through the Wall Through Wall Installation Inside Vertical Through the Roof Installation Outside Vertical Pipe Installation Outside Fresh AIR Connections Mobile Home InstallationStove will not start TroubleshootingIgniter- the pellets will not light Stove will not operate when hotExhaust motor will not function normally Convection blower will not function normallyDial-a-fire has no effect on the fire Auger motor will not function normallyStove keeps going out Stove will not shut downWiring Diagram Back Grill Parts ListComponents Exploded EF 4Exploded Steel Components To the Distributor WarrantyFor the do-it-yourself Individual To the Dealer

EF-IV I specifications

The Enviro EF-IV I is an innovative next-generation environmental control unit designed to meet the diverse needs of modern aviation. With a strong focus on efficiency, reliability, and sustainability, the EF-IV I has garnered attention for its cutting-edge features and advanced technologies that elevate cabin comfort while reducing the ecological footprint.

One of the most notable features of the Enviro EF-IV I is its hybrid cooling technology. By integrating both conventional and thermal energy systems, the unit can operate with higher efficiency across various conditions. This technology allows for significant energy savings while maintaining optimal temperature control in the cabin, making it an ideal choice for eco-conscious airlines looking to minimize operational costs.

The EF-IV I boasts a sophisticated air filtration system that enhances cabin air quality. Utilizing advanced HEPA filters and multi-layer filtration processes, this unit captures airborne particles and contaminants, ensuring that passengers breathe clean and fresh air during their flights. Its intelligent monitoring system continuously assesses air quality parameters and adjusts filtration performance in real-time, providing a proactive approach to maintaining a healthy cabin environment.

In terms of user interface, the EF-IV I is equipped with an intuitive digital control panel that allows crew members to easily monitor and adjust settings. This interface features an interactive display providing valuable data on system performance, energy consumption, and maintenance schedules, empowering operators with real-time insights that contribute to seamless operations.

The compact design of the EF-IV I facilitates easier installation and integration into existing aircraft systems, making it a flexible choice for both new aircraft and retrofitting older models. Its lightweight materials and streamlined construction not only minimize weight and improve fuel efficiency but also enhance overall durability and reduce maintenance requirements.

Finally, the Enviro EF-IV I is built with sustainability in mind. Its materials and manufacturing processes are compliant with international environmental standards, ensuring that the unit adheres to stringent regulations and contributes positively to the overall environmental impact of aviation.

With its advanced features, sustainability focus, and commitment to enhancing passenger experience, the Enviro EF-IV I represents a significant step forward in environmental control technology for the aviation industry. It is a testament to the ongoing innovation and dedication to creating a more sustainable future in air travel.
Top Page Image Contents