Marantz SR5001 manual English, Example AUTO SURROUND, Adjusting The Tone Bass & Treble

SELECTING THE SURROUND MODE

Example: AUTO SURROUND

	SOURCE	SET	OFF	ON
AV SURROUND RECEIVER SR5001	l/
	SLEEP	DISPLAY	P.DIRECT	SURROUND
				LIP SYNC/
	AUTO		dts	INPUT
	1	2	3
	CS	EX/ES	VIRTUAL	T.MODE
	4	5	6
	M-CH ST	STEREO	NIGHT	P.SCAN
	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO

To select the surround mode during playback, press the SURROUND MODE button on the front panel or the SURROUND MODE buttons on the remote.

ADJUSTING THE MAIN VOLUME

	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR
INFO			MENU
	ENTER

Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOLUME 3 / 4 buttons on the remote.

To increase the volume, turn the VOLUME knob clockwise or press VOLUME 3button on the remote, to decrease the volume, turn counterclockwise or press VOLUME 4 button on the remote.

Notes:

•The volume can be adjusted within the range of – ∞ to 18 dB, in steps of 1 dB.

•However, when the channel level is set as described on page 26, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB.

(In this case the maximum volume adjustment range is “18 dB - Maximum value of channel level)

ADJUSTING THE TONE (BASS & TREBLE)

CONTROL

- PRESET +		- TUNING +
DISC+	ANGLE	SUB TITLE	AUDIO
CH-SEL V-OFF		ATT.
	BASS	TREBLE
TV	DVD	VCR	DSS
TUNER	CD	CDR	MD
TAPE	AUX1	AUX2	AMP

REMOTE CONTROLLER

RC5001SR

During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.

(Using the remote control unit)

To adjust the bass effect, press BASS 3 or BASS 4 on the remote.

To adjust the treble effect, press TREBLE 3 or TREBLE 4 on the remote.

Note:

The tone control function can work in the AUTO Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and Multi Ch. Stereo mode.

TEMPORARILY TURNING OFF

THE SOUND

	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME
	MULTI/ CAT	M-SPKR
INFO			MENU
	ENTER

To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the front panel or MUTE button on the remote.

This will interrupt the output to all speakers and the head-phone jack, but it will not affect any recording or dubbing that may be in progress.

When the system is muted, the display will show “MUTE” .

Press the MUTE button again to return to normal operation.

USING THE SLEEP TIMER

LEARNSEND

SOURCE SET OFF ON

l/

SLEEP DISPLAY P.DIRECT SURROUND

			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE

4 5 6

To program the SR4001/SR5001 for automatic standby, press the SLEEP button on the remote. Each press of the button will increase the time before shut down in the following sequence.

OFF 10 20 30 40

90 80 70 60 50

The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed.

When the programmed sleep time has elapsed, the unit will automatically turn off.

Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear.

NIGHT MODE

			LIP SYNC/
AUTO		dts	INPUT
1	2	3
CS	EX/ES	VIRTUAL	T.MODE
4	5	6
M-CH ST	STEREO	NIGHT	P.SCAN
7	8	9
	7.1CH IN	A/D	HT-EQ
CL	0	+10	MEMO
CH/ CAT	SPKR A/B	MUTE	VOLUME

Press the NIGHT button on the remote to turn on the NIGHT mode.

Selecting the Night Mode ON is effective in Dolby Digital only, and it compresses the dynamic range. This softens loud passages such as sudden explosions, to help prevent disturbing others late at night.

To turn off the Night mode, press the NIGHT button again.

ENGLISH

31