Harman Stove Company P61A-2 Ignitor switch to Auto, Room Temperature Mode, Stove Temperature Mode

Page 12

 

P61A-2 AUTOMATIC IGNITION/OPERATION

 

The P61A pellet stove is more than just automatic ignition, it is also automatic temperature control.

 

The automatic system will allow the fire size to be adjusted to match the heating needs and even put

 

the fire out if necessary. If heat is needed after the fire is out, the P61Awill automatically re-ignite

o

and adjust the fire size to match the heating need. The totally automatic room sensor mode is

o

recommended because of its efficiency.

 

 

 

The unit can be switched between "AUTO" and "MANUAL" at any time during operation.

 

 

Ignitor switch to "AUTO"

 

 

Room Temperature Mode

 

 

In "Room Temp Mode" heat output is controlled auto-

 

 

matically by the Room Sensing Probe. When the Room Sens-

 

 

ing Probe calls for heat, the stove will increase output. When

 

 

the Room Sensing Probe is getting close to the set tempera-

 

 

ture, the stove will begin to level off output and keep the fire

 

 

burning at just the right temperature to maintain that setting.

 

 

High output is determined by the feed rate setting.

 

 

This setting, generally on #4, can be increased if higher burn

 

 

rates are necessary. The unit's maximum burn rate should not

 

 

create less then 1" of ash on the burn pot front edge. See

 

 

Fig.2. Overfeeding is not a safety concern, but fuel may be

Room Temperature Mode: This setting will produce a room

wasted if unburned pellets fall into the ash pan.

temperature of 70 degrees with the distribution blower at

In "RoomTemp Mode" a constant fuel consumption rate

medium speed.

 

is sacrificed for exact room temperature. Therefore, as it gets

Stove Temperature Mode

colder more pellets will be burned automatically.

 

 

The distribution blower speed will vary according to the

 

 

position of the mode selector pointer, and fire size.

 

 

Ignitor switch to "AUTO"

 

 

Stove Temperature Mode

 

 

This allows for automatic ignition upon start-up only.The

 

 

unit can then be set at any desired setting. The heat output

 

 

and fuel consumption will remain constant regardless of room

 

 

temperature. The unit's maximum feed rate should not create

 

 

less than 1" of ash on the burn pot front adge. See Fig 2.

This setting will produce medium heat with the

The unit's low burn or maintenance setting is as low as it

will go. It will not go out unless it runs out of fuel or is turned

distribution blower on "low".

 

 

off.

 

Shut-Down Procedure

 

To kill the fire or stop burning the stove, turn the Mode

 

Selector to "OFF". This will cause the fire to diminish and

 

burn out. When the fire burns out and the stove cools down

 

everything will stop.

 

If you pull the plug to shut down the stove, all motors

 

will stop. This may cause incomplete combustion and smoke

 

in the firebox. If the load door is opened the smoke may es-

 

cape.

This setting will produce continuous maximum heat output

The best way to shut down the stove is simply let it run

with the distribution blower at full speed.

out of pellets, then the stove will shut down automatically.

12 P61A Pellet Stove

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation & Operating Manual Safety NoticeP61A Pellet Stove Table of Contents Assembly and Installation UnpackingFirebrick Flame GuideInstallation InstallingMobile Home Installation With outside air installed, 18î VentingVenting Vent PipeOutside Air #1 Preferred method #2 Preferred method#4 Installing into an existing chimney US only #5 Installing into an existing fireplace chimney US only#7 Installing into an existing chimney US and Canada Minimum flue vent configuration #8 Installing through the ceiling ventIgnitor switch to Auto Room Temperature ModeStove Temperature Mode Shut-Down ProcedureTurn Mode Selector to OFF P61A-2 Automatic Start UPStarting First Fire Ignitor Switch to Manual P61A-2 Manual IGNITION/OPERATIONStarting First Fire Ignitor Switch toMANUAL down position P61A-2 Manual Start UPFill hopper with pellets and remove ashes as required.1 Status light error messages Blinks In Igniter Auto. Mode Only IndicatesP61A-2 Automatic Ignition ESP Control P61A-2 Low Draft Voltage Adjustment Low Draft Voltage AdjustmentRoom Sensor and Rear Shield Installation Room Sensor Installation Rear ShieldsMaintenance CleaningRemoving Ashes Soot and Fly Ash P61A-2 Maintenance Burn Pot Burn Pot Cleaning and MaintenanceP61A-2 Trouble-Shooting Cleaning Burn PotHelpful Hints FuelP61A-2 Feeder and Specifications Specifications23.5Weight 249 lbs Blower 135 cfm Feed Rate P61A FeederDoor Options Optional TrimOptions Side Heat ShieldsHopper Extension P61A-2 Wiring Diagram P61A-2 Parts List Harman Gold Warranty Harman Gold Warranty Year Transferable Limited

P61A-2 specifications

The Harman Stove Company P61A-2 is a premier pellet stove that exemplifies modern design and efficient heating technology. Known for its high performance and user-friendly features, this model is a popular choice among homeowners seeking an eco-friendly heating solution.

One of the standout features of the P61A-2 is its impressive heating capacity. With the ability to produce up to 51,000 BTUs (British Thermal Units), it can effectively heat spaces of up to 2,800 square feet. This makes the stove suitable for both large living areas and open floor plans, ensuring consistent warmth during the chilly months.

The P61A-2 also boasts a sleek, contemporary design that fits seamlessly into various home decors. Available in several finishes, including classic black and rich bronze, it enhances the aesthetic appeal of any room. Its compact size allows for versatile installation options, whether it's in a corner or as a freestanding unit.

In terms of technology, the Harman P61A-2 features an advanced pellet feed system that maximizes efficiency and minimizes waste. This system ensures a steady supply of pellets to the burn pot, optimizing combustion and resulting in high efficiency ratings. The stove has an automatic ignition system, allowing users to easily start it with the push of a button, enhancing convenience and reducing the hassle often associated with traditional wood-burning stoves.

The stove is equipped with a unique heat exchanger and blower system that enhances heat distribution, ensuring warmth is circulated evenly throughout the room. Its adjustable variable-speed blower allows users to customize airflow, catering to their specific heating needs.

Additionally, the P61A-2 is designed with an easy-to-use control panel, providing options for temperature setting, operating modes, and diagnostics. This user-friendly interface allows for effortless operation, even for those new to pellet stoves.

Maintenance is simplified with the P61A-2, as it includes an easy-access clean-out door for quick ash disposal and a removable burn pot for thorough cleaning. The durable construction and high-quality materials ensure longevity, making the P61A-2 a reliable heating solution for years to come.

In summary, the Harman Stove Company P61A-2 combines powerful heating capabilities with innovative technology, a stylish design, and user-friendly features, making it a top choice for efficient home heating.
Top Page Image Contents