Harman Stove Company P61A-2 owner manual Installing, Mobile Home Installation

Page 5

Installation

Installing

Place the stove on a noncombustible floor protector that extends 6 inches to the front, 6 inches to the sides and 1 inch to the rear of the stove. The minimum floor protector material is 24 gauge sheet metal.

Place the stove away from combustible walls at least as far as shown in figures 3,4 and 5. Please note the difference in side wall clearance with and without side shields.

Note that the clearances shown are minimum for safety but do not leave much room for access when clean- ing or servicing. Please take this into account when plac- ing the stove.

Connect the power cord to a 120 V.A.C. 60Hz grounded receptacle. (A surge protector is recommened to protect the circuit board).

Prior to installing the flue pipe, connect a draft meter to the stove as shown in fig. 6. (The draft meter must have a minimum range of 0-.5). However, prior to taking the draft reading be sure all doors and windows in the home are closed. Record the draft reading_______. If

this reading is more than .05" lower than the unconnected reading, check for possible restrictions or the need for outside air (see page 7).

Mobile Home Installation

When installing this unit in a mobile home several re- quirements must be followed:

1.The unit must be bolted to the floor. This can be done with 1/4" lag screws through the 2 holes in the base plate.

2.The unit must also be connected for the outside air. See page 8.

3.Floor protection and clearances must be followed as shown.

4.Unit must be grounded to the metal frame of the mobile home.

CAUTION: This appliance must be vented to the out- side.

Due to high temperatures, the stove should be placed out of traffic and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burn to skin and/or clothing.

Young children should be carefully supervised when they are in the same room as the stove.

Clothing and other flammable materials should not be placed on or near this unit.

Installation and repair of this Harman Stove should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning will be required. It is imperative that control compartments, burners, and circu- lating air passageways of the stove be kept clean.

9"-13"

9"-13"

9" With Side Shields

13" Without Side Shields

Fig. 3

1"

2"

 

 

 

 

12"

Shields

6"

 

6"

FLOOR PROTECTOR

6"

With Side

 

 

 

Fig. 4

 

 

18"

FLOOR PROTECTOR

Fig. 5

Without Side Shields

Fig. 6

P61A Pellet Stove 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Safety Notice Installation & Operating ManualP61A Pellet Stove Table of Contents Unpacking Assembly and InstallationFirebrick Flame GuideMobile Home Installation InstallationInstalling Venting With outside air installed, 18îOutside Air VentingVent Pipe #2 Preferred method #1 Preferred method#5 Installing into an existing fireplace chimney US only #4 Installing into an existing chimney US only#7 Installing into an existing chimney US and Canada #8 Installing through the ceiling vent Minimum flue vent configurationRoom Temperature Mode Ignitor switch to AutoStove Temperature Mode Shut-Down ProcedureStarting First Fire Turn Mode Selector to OFFP61A-2 Automatic Start UP P61A-2 Manual IGNITION/OPERATION Ignitor Switch to ManualFill hopper with pellets and remove ashes as required.1 Starting First Fire Ignitor Switch toMANUAL down positionP61A-2 Manual Start UP P61A-2 Automatic Ignition ESP Control Status light error messagesBlinks In Igniter Auto. Mode Only Indicates Low Draft Voltage Adjustment P61A-2 Low Draft Voltage AdjustmentRoom Sensor Installation Rear Shields Room Sensor and Rear Shield InstallationRemoving Ashes MaintenanceCleaning Soot and Fly Ash Burn Pot Cleaning and Maintenance P61A-2 Maintenance Burn PotCleaning Burn Pot P61A-2 Trouble-ShootingHelpful Hints FuelSpecifications23.5 P61A-2 Feeder and SpecificationsWeight 249 lbs Blower 135 cfm Feed Rate P61A FeederOptional Trim Door OptionsHopper Extension OptionsSide Heat Shields P61A-2 Wiring Diagram P61A-2 Parts List Harman Gold Warranty Year Transferable Limited Harman Gold Warranty

P61A-2 specifications

The Harman Stove Company P61A-2 is a premier pellet stove that exemplifies modern design and efficient heating technology. Known for its high performance and user-friendly features, this model is a popular choice among homeowners seeking an eco-friendly heating solution.

One of the standout features of the P61A-2 is its impressive heating capacity. With the ability to produce up to 51,000 BTUs (British Thermal Units), it can effectively heat spaces of up to 2,800 square feet. This makes the stove suitable for both large living areas and open floor plans, ensuring consistent warmth during the chilly months.

The P61A-2 also boasts a sleek, contemporary design that fits seamlessly into various home decors. Available in several finishes, including classic black and rich bronze, it enhances the aesthetic appeal of any room. Its compact size allows for versatile installation options, whether it's in a corner or as a freestanding unit.

In terms of technology, the Harman P61A-2 features an advanced pellet feed system that maximizes efficiency and minimizes waste. This system ensures a steady supply of pellets to the burn pot, optimizing combustion and resulting in high efficiency ratings. The stove has an automatic ignition system, allowing users to easily start it with the push of a button, enhancing convenience and reducing the hassle often associated with traditional wood-burning stoves.

The stove is equipped with a unique heat exchanger and blower system that enhances heat distribution, ensuring warmth is circulated evenly throughout the room. Its adjustable variable-speed blower allows users to customize airflow, catering to their specific heating needs.

Additionally, the P61A-2 is designed with an easy-to-use control panel, providing options for temperature setting, operating modes, and diagnostics. This user-friendly interface allows for effortless operation, even for those new to pellet stoves.

Maintenance is simplified with the P61A-2, as it includes an easy-access clean-out door for quick ash disposal and a removable burn pot for thorough cleaning. The durable construction and high-quality materials ensure longevity, making the P61A-2 a reliable heating solution for years to come.

In summary, the Harman Stove Company P61A-2 combines powerful heating capabilities with innovative technology, a stylish design, and user-friendly features, making it a top choice for efficient home heating.
Top Page Image Contents