P61A-2 Automatic Ignition ESP Control

P61A-2 AUTOMATIC IGNITION ESP CONTROL

Power Light Indicates power to the control.

Status Light

Will be lit in either stove or room temp mode when pointer is not within off position band except after normal shut down. Blinks to indicate errors listed below.

Indicates power to distribution blower.

Indicates power to combustion blower

Indicates power to the feed motor.

Indicates ignitor is on.

Temp dial

Allows you to adjust the room temperature in Room Temp Mode using the outer scale marked in degrees Fahrenheit. It also allows you to adjust the stove temperature while in Stove Temp Mode using the inner scale marked from 1 to 7.

Status light error messages:

Dealer Diagnostic Port For dealer maintenance only. Requires special DDM monitor supplied to Harman Dealers exclusively.

Feed adjuster

Sets the maximum feed rate

Test

Runs all motors at full speed for one minute to check operation. After two minutes the stove will go to minimum burn and the blowers will alternate from high to low every minute to remind you that you are still in "Test Mode".

Ignitor switch

Set to appropriate

Start-Up mode.

Distribution Blower speed adjustment range.

L = low H = high

Variable speed anywhere between L and H; although as the stove temp. goes up , so does the L and H scale.

Mode Selector

Allows you to choose between Room Temp Mode, Stove Temp Mode, or OFF. Also allows you to vary the distribution blower speed by turning the knob to the high or low side of each mode.

1 Blink: Indicates control board self diagnostic failure. This requires a manual reset*.

2 Blinks: Indicates that the jumper (J2) on the rear of the control board is not connected. Without this jumper the unit will only burn at minimum rate.

3 Blinks: Indicates ESP (Exhaust Sensing Probe) fail- ure. This requires a manual reset*.

4 Blinks: Can occur only in Room Temp Mode and indicates Room Sensing Probe failed or not installed. If a Room Sensing Probe is then installed, the status light will automatically reset.

5 Blinks (In Igniter Auto. Mode Only): Indicates

that the unit has failed to light within the 36 minute start cycle. To reset - Turn Mode Selector to "OFF", then

16 turnP61Ato eitherPellStovemode again.)

6 Blinks : Indicates that the control has calculated poor or incomplete combustion occurring for more than 50

minutes.

A six blink status may be set if the stove is allowed to run out of pellets. To reset, turn mode selector to "OFF" then back on to the desired mode. If the unit was not out of pellets, see Troubleshooting section for more de- tails.

*Manual reset- disconnect power cord for a few sec- onds and reconnect. If error still occurs call your Dealer. NOTICE: When power is given to the stove, the con- trol board will blink a few times to indicate current ver- sion of control board. This should not be confused with error messages.

P61A-2 specifications

The Harman Stove Company P61A-2 is a premier pellet stove that exemplifies modern design and efficient heating technology. Known for its high performance and user-friendly features, this model is a popular choice among homeowners seeking an eco-friendly heating solution.

One of the standout features of the P61A-2 is its impressive heating capacity. With the ability to produce up to 51,000 BTUs (British Thermal Units), it can effectively heat spaces of up to 2,800 square feet. This makes the stove suitable for both large living areas and open floor plans, ensuring consistent warmth during the chilly months.

The P61A-2 also boasts a sleek, contemporary design that fits seamlessly into various home decors. Available in several finishes, including classic black and rich bronze, it enhances the aesthetic appeal of any room. Its compact size allows for versatile installation options, whether it's in a corner or as a freestanding unit.

In terms of technology, the Harman P61A-2 features an advanced pellet feed system that maximizes efficiency and minimizes waste. This system ensures a steady supply of pellets to the burn pot, optimizing combustion and resulting in high efficiency ratings. The stove has an automatic ignition system, allowing users to easily start it with the push of a button, enhancing convenience and reducing the hassle often associated with traditional wood-burning stoves.

The stove is equipped with a unique heat exchanger and blower system that enhances heat distribution, ensuring warmth is circulated evenly throughout the room. Its adjustable variable-speed blower allows users to customize airflow, catering to their specific heating needs.

Additionally, the P61A-2 is designed with an easy-to-use control panel, providing options for temperature setting, operating modes, and diagnostics. This user-friendly interface allows for effortless operation, even for those new to pellet stoves.

Maintenance is simplified with the P61A-2, as it includes an easy-access clean-out door for quick ash disposal and a removable burn pot for thorough cleaning. The durable construction and high-quality materials ensure longevity, making the P61A-2 a reliable heating solution for years to come.

In summary, the Harman Stove Company P61A-2 combines powerful heating capabilities with innovative technology, a stylish design, and user-friendly features, making it a top choice for efficient home heating.