Reloading, Blower | Harman Stove Company TL200 specification

Exception TL200 Wood Stove

Operation

Air Control

Building and Maintaining the Fire

The air control lever is located directly below the ash lip of the stove. Using this lever you will be able to vary the amount of air delivered to the fire, creating a range of heat outputs. The low heat output setting is to the left, and high is to the far right. Do not, under any circumstances, alter the configuration or operation of the air control lever.

Less

Below this setting, run the optional blower on "low" or "OFF". Higher air movement cools the secondary combustionarea which can leadto poor combustion and lower efficiency.

The Harman Exception was tested with the fuel door open and closed. If you operate under normal conditions keep door closed.

Set the air control lever at the maximum heat output setting, all the way to the right. Open the bypass damper by moving the top loading handle forward one position (ap- proximately 3"). The convection blower, if installed, should be off for the first five minutes after a reload.

Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this heater. Keep all

such liquids well away from the heater while it is in use.

Build a bed of paper and kindling; place several 1

"- 2" (25 mm - 50 mm) split pieces of dry wood on top, followed by a few 2" - 3" (50 mm - 80 mm) split pieces.

Ignite the paper a nd close the door. Allow the fire to burn until a good charcoal bed, 2" - 3" (50 mm - 80 mm) is formed; close the bypass damper

by pushing the top loading handle all the way back until it locks closed. (You may need to leave the load door open a crack to get the blaze going properly, but never leave the stove unattended with door open.) Add more wood to cre- ate a deeper charcoal base (3" - 4", or 80 mm - 100 mm thick); remember to open the bypass damper if you are loading fromthe front. This will allow the exhaust gases to pass directly into the flue outlet and reduce smoke spill- age during refueling.

Once the charcoal bed is established you may add a full load of dry wood. After adding the fuel, leave the damper open and the air setting at maximum for 5 to 15 minutes; close the damper and allow the air setting to remain on high for an additional 5 to 10 minutes. Then adjust the air lever and blower speed for the desired heat output.

Reloading

Once you have prepared and maintained a thick char- coal bed, you should be able to reload the stove, allow some open damper burning at the maximum air setting, close the damper and reset the air control in about five minutes.

Blower

To regulate the speed of the optional convection blower, adjust the control from low to high by turning the knob located on the blower. The blower speed should be matched to the air control lever setting.

When the air setting is low, the blower should al- ways be at the minimum setting (corresponding to a blower speed of 750 RPM.) At higher settings, above first notch on the air control, the blower may be set to your desired comfort level. Be sure that the blower cord does not run

under, over, above or in front of the stove.

TL200 specifications

The Harman Stove Company TL200 is a standout pellet stove designed to deliver both efficiency and elegance to any home. Recognized for its robust construction and advanced features, the TL200 is a popular choice among homeowners looking to maximize heat while minimizing environmental impact.

One of the main features of the TL200 is its high-efficiency pellet burning capability. The stove boasts an impressive EPA certification, which means it meets strict environmental standards for emissions. This is essential not only for regulatory compliance but also for residents who are mindful of their carbon footprint. The stove efficiently converts pellets into heat, with low emissions that contribute to cleaner air quality.

The TL200 incorporates innovative technology to ensure optimal performance. It comes equipped with an intuitive digital control panel, allowing users to easily adjust the heating output according to their needs. This feature is complemented by an automatic igniter that takes the hassle out of starting the stove. With a programmable thermostat, homeowners can maintain their desired temperature effortlessly, leading to energy savings and enhanced comfort.

Another notable characteristic of the TL200 is its large hopper capacity. The stove is designed to hold a substantial amount of pellets, providing extended burn times. This means less frequent reloading, allowing for uninterrupted heating during those cold winter months. The TL200 can burn for up to 48 hours on a single load, making it an excellent choice for both convenience and efficiency.

The design of the TL200 is another aspect that sets it apart. It combines traditional aesthetics with modern functionality. The stove features a sleek, contemporary look, available in various finishes to complement any décor. The large viewing window allows users to enjoy the beauty of the flames while providing adequate heat to the room.

Safety features are also paramount in the TL200 design. The stove includes a built-in safety sensor that monitors temperature levels, ensuring that the unit does not overheat. An automatic shutoff feature provides peace of mind for homeowners, making it a safe option for families.

In conclusion, the Harman Stove Company TL200 pellet stove stands out for its eco-friendly burning technology, user-friendly controls, ample fuel capacity, attractive design, and safety features. For those seeking a reliable and efficient heating solution, the TL200 is an impressive option that combines performance with style.

Harman Stove Company TL200 manual Air Control Building and Maintaining the Fire, Reloading, Blower