Casablanca Fan Company III manual Speed Operation, Speed Optional Light Fixture Installation

3-SPEED ♦OPERATION

Pull-chain switches on the fan control the fan and reverse. Using the fan control pull-chain switch: Fan off at start.

First pull: fan ON, low speed

Second pull: medium speed

Third pull: high speed

Fourth pull: fan OFF

Direction of blade rotation is controlled by the reverse pull chain on the side of the switch housing.

No changes in household wiring are required.

REVERSE	FAN & SPEED
PULL CHAIN	CONTROL
SWITCH	PULL CHAIN SWITCH

3-SPEED ♦ OPTIONAL LIGHT FIXTURE INSTALLATION

NOTE: If a separate circuit is used to control the lights from a wall control, the BLUE D1-Option wire in the canopy should be connected to that switch leg with the BLACK fan power wire.

1.Refer to light kit instructions to assemble and attach your light kit correctly.

2.Remove the two 8-32 screws from the switch housing cap.

3.Remove the plug from switch housing.

4.Install pull-chain switch and finger tighten collar on switch.

5.Connect one wire from pull-chain switch to the BLUE D1-Option wire. Secure splice with a wire nut.

6.Connect other wire from pull-chain switch to BLACK wire from light kit. Secure splice with a wire nut.

7.Connect WHITE wire from switch housing to WHITE wire from light kit. Secure splice with a wire nut.

8.At the canopy, connect the BLACK and BLUE wires.

SWITCH

HOUSING

COLLAR

TROUBLESHOOTING

Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance.

Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accu- mulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents. These will damage the finish. Painted and high-gloss blades may be cleaned in the same manner.

Blades: Wood finish blades should be cleaned with a furniture pol- ishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty.

Never Lubricate this Fan!

The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. Do not attempt to oil the motor.

Changing Light Bulbs

Be sure to turn power to the fan OFF at the wall switch or circuit breaker before changing light bulbs. Replace bulbs with same type as removed from the fixture. Each fan is rated for a maximum TOTAL wattage of lighting.

Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty.

PROBLEM	3-SPEED	POSSIBLE REMEDIES..
FAN WILL NOT START	Check main circuit fuses, circuit breakers, or wall switch position.
	Check all wire connections, making sure the power is turned off during this inspection.
FAN WOBBLES OR SHAKES	Check that reverse switch is not set in center of throw.
	Be sure canopy pin is properly set into the slot on the ball.
EXCESSIVELY	Check the screws holding the blade holders to the flywheel (or direct drive motor). Tighten as necessary.
FAN NOISY DURING	Check that bladeholders have not been bent during installation.
	Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary.
OPERATION	Tighten the blade to bladeholder screws.
	Tighten canopy screws and mounting plate assembly.
	Check and tighten blade holders to flywheel (or direct drive motor).
	Make sure all screws in the motor housing are snug, but not overly tight.
	Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or have
BREAK-IN PERIOD	fallen off the wire splices. Tighten or adjust as necessary.
	Let fan run at high speed for two (2) hours
DOES NOT RUN ON	If new, “break-in” may be required - run at higher speed for several days
LOW SPEED

FAN RUNS SLOWLY IN EITHER DIRECTION IF ROTATION IS STARTED BY HAND; WILL NOT REVERSE: Defective reverse switch; defective

capacitor; or open motor winding: Replace reverse switch assembly; replace PCB assembly; or replace motor unit.

FAN WILL NOT OPERATE AT PROPER SPEEDS OR WILL NOT OPERATE AT ANY SPEED: Defective three-speedpull-chain switch assembly; or

defective capacitor: Replace three-speed pull-chain switch assembly; or replace PCB assembly.

8