Hard water leakage after | a. | Improper regeneration. | a. | Repeat regeneration after making |
regeneration. |
|
|
| certain correct regenerant dosage was |
|
|
|
| set. |
| b. | Leaking of external bypass valve. | b. | Replace bypass valve. (Contact dealer). |
| c. | c. | Replace | |
| d. | System capacity too low due to | d. | Reset control and program resin volume |
|
| incorrect resin volume setting |
| to correct setting |
|
|
|
|
|
Control will not draw | a. | Low water pressure. | a. | Make correct setting according to |
regenerant. |
|
|
| instructions. |
| b. | Restricted drain line. | b. | Remove restriction. |
| c. | Injector plugged. | c. | Clean injector and screen. |
| d. | Injector defective. | d. | Replace injector and cap. (Contact |
|
|
|
| dealer). |
| e. | Valve disc 2 and/or 3 not closed. | e. | Remove foreign matter from disc and |
|
|
|
| check disc for closing by pushing in on |
|
|
|
| stem. Replace if needed. (Contact |
|
|
|
| dealer). |
| f. | Air check valve prematurely closed. | f. | Put control momentarily into brine refill. |
|
|
|
| Replace or repair air check if needed. |
|
|
|
| (Contact dealer). |
|
|
|
|
|
Control will not regenerate | a. | AC adapter or motor not connected. | a. | Connect power. |
automatically. | b. | Defective motor. | b. | Replace motor. (Contact dealer). |
| c. | Fouled or defective turbine. | c. | Clean or replace turbine assembly. |
| d. | Defective turbine cable. | d. | Replace turbine cable. |
|
|
|
|
|
Control regenerates at wrong | a. | Controller set incorrectly. | a. | Correct the time setting according to |
time of day. |
|
|
| instructions. |
|
|
|
|
|
Intermittent or irregular | a. | Low water pressure. | a. | Set pump to maintain 20 psi at |
regenerant draw. | b. | Defective injector. |
| conditioner. |
| b. | Replace injector (Contact dealer). | ||
|
|
| ||
|
|
|
|
|
No conditioned water after | a. | No regenerant in regenerant tank. | a. | Add regenerant to regenerant tank. |
regeneration. | b. | Injector plugged. | b. | Clean injector and screen. |
| ||||
| c. | Air check valve closes prematurely. | c. | Quick cycle control into regenerant |
|
|
|
| draw/slow rinse. Replace or repair air |
|
|
|
| check if needed. (Contact dealer). |
|
|
|
|
|
Backwashes or purges at | a. | Incorrect drain controller used. | a. | Replace with correct size controller |
excessively low or high rate. |
|
|
| (Contact dealer). |
| b. | Foreign matter affecting valve | b. | Remove drain controller and clean ball |
|
| operation. |
| and seat. |
|
|
|
|
|
Run out of conditioned water | a. | Improper regeneration. | a. | Repeat regeneration, |
between regenerations. | b. | Incorrect resin volume setting | b. | Reset control and program resin volume |
| ||||
|
|
|
| to correct setting |
|
|
|
|
|
Control displays 1 - x (1 thru | a. | Control is in test mode | a. | Press control keys in order from left to |
4) |
|
|
| right. |
|
|
|
|
|
37