Rheem 136-1826 Receivingequipment, Installation Regulations, Water Flow, Water Conditions

Page 7

A. INTRODUCTION

WE RECOMMEND THAT THIS MANUAL BE REVIEWED THOROUGHLY BEFORE INSTALLING THE WATER HEATER. SHOULD ANY QUESTIONS ARISE, NOT COVERED BY THIS DATA, CONTACT YOUR LOCAL DISTRIBUTOR OR THE SERVICE DEPARTMENT AT THE FACTORY.

MODELIDENTIFICATION

The model number of the water heater is found on the rating plate. Each model number identifies the application, the construction and the function of the water heater , and provides a positive means of identification for application, installation, operation, service and parts of the unit in a minimum amount of time.

RECEIVINGEQUIPMENT

On receiving equipment it is suggested that you

•Review packing slip for the number of packages.

•Inspect for concealed damage immediately.

•Advise carrier, in writing, of shortages or damage.

•Claims are filed by the receiver against the carrier. The carrier, not the shipper, is responsible for any shortage or damage whether visible or concealed.

B.INSTALLATION GUIDELINES

INSTALLATION REGULATIONS

THE INSTALLATION MUST CONFORM WITH THESE INSTRUCTIONS, REQUIREMENTS OR CODES OF AUTHORITIES HAVING JURISDICTION, THE LATEST EDITION OF THE NATIONAL FUEL GAS CODE, ANSI Z223.1 AND THE NATIONAL ELECTRICAL CODE.

ANY ALTERATION OR MODIFICATION TO THE WATER HEATER, ITS COMPONENTS OR ITS INTENDED APPLICATION MAY VOID THE WARRANTY EXTENDED WITH THE PRODUCT BY THE MANUFACTURER.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can damage the

 

water heater, or create a hazard resulting in asphyxiation, explosion or fire.

WATER FLOW

Low water content heat exchangers require continuous flow for proper operation.

WATER CONDITIONS:

Domestic Hot water heaters are designed for operation with various water conditions. Corrosive water that has high chlorine content or other chemicals require that the tubes in the heat exchanger be cupro-nickel. Provide us with an analysis of water where this potential exists.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Important Warning Catalog NO. RM-001Electric Code ANSI/NFPA Index Series GB For circulating tank systems Through 1826 Mbtuh Construction FeaturesSpecification Data Page Shipping Water Conditions Installation RegulationsReceivingequipment Water FlowCombustible Floor Base BaserequirementsBoiler Part Protected Surfaces CombustibleconstructionclearancesModel Combustion and Ventilation AIR SupplyRecommended Minimum AIR Openings MODEL181-399MODELS926-1758 Models 512Indoorheaters Models MODELS181-399 Heater Before Heater After Drafthood InstallationPage Fig. #7043.1 Outdoorwaterheaters Power VentingVent Damper Installation Models 136 Through 264 Where Required LocationNormal Operation Summary MountingPipe Sizes Gas Natural PropaneBTU/CF SP. GRFig.#8185.1 Test piping as followsCold Water Supply WaterGPM NPT HOT Water Supply Heater TanktemperaturecontrolSeries with 115 Volt Supply to the Heater Piping DIAGRAM-1 Heater 1 Tank Thermostat Supplied Installation Water Heater PlumbingSequenceofoperation Piping Must be Equal Between Tees and TANKS. Notes Piping DIAGRAM-1 Heater 2 TankFig. # 8067-RHEEM Piping DIAGRAM-1 Heater 3 TankPiping DIAGRAM-1 Heater 4 Tank Piping DIAGRAM-2 Heater 1 Tank Special Thermostat and Well Energy Saving Pump Control Description of Controls in GeneralElectronicignition Flow Switch Tankstat Temperature ControlHighlimit ON-OFFOPERATION ElectricalSingle Stage Tankstat START-UPScalding TIME/TEMPERATURE Relationships in ScaldsFor Your Safety Read Before Operating To Shut Down Close all manual gas valves. Turn off electric powerMonthly Inspectionand MaintenanceproceduresSix Months Venting System Inspection System Shut Down ProcedureService Assistance Burner InspectionTrouble Shooting Problem If okay replace ignition module Start Electrical Electronic Ignition IID Models 512Wiring Diagram KEY Wiring Diagrams Wiring Diagram Models 512 Wiring Diagram Models 331Wiring Diagram Models 726 Wiring Diagram ModelsFig. # 1967e Wiring Diagram Model 825 Wiring Diagram Models 962Model 136 GB only Replacement Parts ListsModel 136 GB only Models 181, 264, 331, 399 GB Page Models 181, 264, 331, 399 GB Models 181, 264, 331,339 GB Models 512, 627, 726, 825 GB Models 512, 627, 726, 825 GB Models 512, 627, 726, 825 GB Models 926-1826 GB Models 926-1826 GB Models 926-1826 GB

136-1826 specifications

The Rheem 136-1826 is a highly efficient heating and cooling unit designed to provide reliable performance and comfort in residential settings. This unit is particularly notable for its advanced features, robust technologies, and outstanding characteristics that set it apart in the HVAC market.

One of the defining features of the Rheem 136-1826 is its energy efficiency. Rated with a high Seasonal Energy Efficiency Ratio (SEER), this unit efficiently converts energy into cooling output, leading to significant savings on utility bills. The environmentally friendly refrigerants used in its operation comply with current global regulations and aim to minimize any negative impact on the ozone layer.

Additionally, the Rheem 136-1826 incorporates advanced climate control technologies. Its innovative multi-stage compression offers superior cooling performance and an enhanced ability to maintain comfortable temperatures, even during extreme weather conditions. The variable-speed motor allows for precise airflow management, leading to quieter operation and improved indoor air quality by minimizing dust and allergens in circulation.

Another remarkable attribute of the Rheem 136-1826 is its smart technology integration. Homeowners can connect the unit to Wi-Fi and control it remotely through a mobile app. This feature not only provides convenience but also allows users to monitor system performance, adjust settings, and receive maintenance reminders. The programmable thermostat included in the setup further enhances energy conservation efforts, enabling users to tailor their heating and cooling schedules to their lifestyle.

In terms of installation and maintenance, the Rheem 136-1826 has been designed with user-friendliness in mind. Its compact size allows for easy installation in various locations, making it a versatile choice for different home designs. The durable construction materials used in this unit ensure longevity and reduced maintenance needs over time.

Overall, the Rheem 136-1826 stands out for its combination of energy efficiency, advanced cooling technologies, smart features, and ease of use. It is an ideal choice for homeowners looking for a reliable and efficient heating and cooling solution that not only enhances indoor comfort but also contributes to long-term energy savings. Whether replacing an old system or installing a new one, the Rheem 136-1826 is well-equipped to meet the demands of modern living.
Top Page Image Contents