Desa installation manual Connecting to GAS Supply, Installation Items Needed

Page 13

INSTALLATION

Continued

IMPORTANT: Make sure the heater burners are level. If heater is not level, heater will not work properly. For thermostat models, avoid damage to thermostat bulb. Avoid nicks or sharp bends in thermostat bulb wire. Keep thermostat bulb in mounting bracket until ready to mount base to floor. See Optional Positioning Of Thermostat Sensing Bulb, page 29.

Installation Items Needed

•hardware package (provided with heater)

•approved flexible gas hose (not provided) (if allowed by local codes)

•sealant (resistant to propane/LP gas, not provided)

•electric drill with 3/16" drill bit

•flathead screwdriver

1.Apply pipe joint sealant lightly to male threads of the fitting to be threaded into gas regulator. Connect approved flexible gas hose to gas regulator of heater (see Figure 11).

IMPORTANT: Hold gas regulator with wrench when connecting flexible gas hose.

2.Locate masonry screws in hardware package.

3.Position heater base assembly in fireplace.

4.Place logs in their proper position on heater base (see Installing Logs, page 16).

5.Center heater base and logs front-to-front and side-to-side in fireplace.

6.Carefully remove logs without moving heater base.

7.Mark screw locations through holes in mount- ing brackets (see Figure 12). If installing in a brick-bottom fireplace, mark screw locations in mortar joint of bricks.

8.Remove heater base from fireplace.

9.Drill holes at marked locations using 3/16" drill bit.

10.Attach base assembly to fireplace floor using two masonry screws (in hardware package) (see Figure 12).

Fitting

Heater Gas

 

 

Regulator

Masonry

Screw

Mounting

Bracket

Figure 12 - Attaching Base Assembly to

Fireplace Floor

CONNECTING TO GAS SUPPLY

WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: A qualified service person must connect heater to gas supply. Follow all local codes.

CAUTION: Never connect propane/LPheater directly to the propane/LP supply. Propane/LP heaters require an external regu- lator (not supplied). Install the external regulator between the heater and propane/LP supply.

WARNING: For natural gas units, never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

Flexible Gas Hose

(if allowed by local codes)

Figure 11 - Attaching Flexible Gas Hose

to Heater Gas Regulator

113101-01C

www.desatech.com

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Patent Pending 24 Variable MANUALLY-CONTROLLED ModelsTable of Contents Safety Information Product Identification Local Codes Product FeaturesUnpacking AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Providing Adequate VentilationUnusually Tight Construction Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationMinimum Firebox Size Log Size Side Wall CeilingFront Rear Minimum Noncombustible Material ClearancesLog Set Mantel ClearancesLog Set Floor ClearancesInstalling Heater Base Installing Damper Clamp Accessory for Vented OperationAssembly Installation Items Needed Connecting to GAS SupplyNatural Pointing DownTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Installing Back Log Pressure Testing Heater Gas ConnectionsInstallation What to do if YOU Smell GAS Operating HeaterSlightly depress and turn control knob coun Lighting InstructionsVariable Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance STOP! Read the safety information, page 20, column Thermostat Control Operation Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesODS/PILOT and Burner Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole Service Hints Technical ServiceReplacement Parts Observed Problem Possible Cause Remedy TroubleshootingODS/pilot lights but flame goes See Cleaning and Mainte Statement above Gas leak. See WarningFor Masonry and FACTORY- Built Metal Fireplace Optional Positioning Thermostat Sensing BulbSpecifications Parts Central AccessoriesEquipment Shutoff Valve GA5010 Fireplace HoodIllustrated Parts Breakdown Variable MANUALLY-CONTROLLED Winchester OAK Models Parts ListIllustrated Parts Breakdown THERMOSTATICALLY-CONTROLLED Royal English OAK Models Keep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS Fireplace

CGS2718PA, CGS2718NA, CGS3124PA, CGS3124NA, SGS3124PA, SGS3124NA,CLD3018PTA, CLD3018NTA, CLD3924NTB, CLD3924PTB specifications

The models Desa CGS2718PA, CGS2718NA, CGS3124PA, CGS3124NA, SGS3124PA, SGS3124NA, CLD3018PTA, CLD3018NTA, CLD3924NTB, and CLD3924PTB are part of a versatile range of consumer appliances that combine modern technology with practical design. Each model brings its unique set of features aimed at enhancing user experience while maintaining high performance and efficiency.

Starting with the CGS series, the CGS2718PA and CGS2718NA are known for their compact sizes, making them ideal for smaller spaces without compromising functionality. They offer advanced digital controls, providing users with precise temperature settings and easy operation. Both models feature a sleek design, available in contemporary finishes that complement modern kitchen aesthetics.

The CGS3124PA and CGS3124NA expand on these features, offering greater capacity and additional functionalities such as enhanced cooking modes. These models incorporate the latest multi-cooking technology, allowing users to steam, bake, and roast with ease. Their energy-efficient systems help reduce power consumption while delivering great performance.

In the SGS series, both SGS3124PA and SGS3124NA prioritize efficiency and durability. Their robust construction is designed to withstand the rigors of daily use, while their intuitive controls simplify operation. These models are equipped with smart sensors that monitor cooking conditions and adjust settings automatically, ensuring optimal results every time.

Moving to the CLD series, the CLD3018PTA and CLD3018NTA are designed for versatility, featuring multiple cooking settings that cater to diverse culinary needs. These models excel in user-friendly interfaces, making meal preparation accessible to everyone, from novice cooks to experienced chefs.

The CLD3924NTB and CLD3924PTB stand out with their larger capacity and advanced technology that includes self-cleaning options, programmable timers, and compatibility with smart home systems. This adds another layer of convenience to the cooking process, allowing users to plan meals according to their schedules.

Overall, these models offer a comprehensive approach to modern cooking with an emphasis on efficiency, ease of use, and stylish design. They not only meet the demands of everyday cooking but also enhance the overall experience in the kitchen, making them a valuable addition to any home.
Top Page Image Contents