Desa installation manual Pressure Testing Heater Gas Connections, Installing Back Log

Page 16

INSTALLATION

Continued

Pressure Testing Heater Gas

Connections

1.Open equipment shutoff valve (see Figure 15, page 15).

2.Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

3.Make sure control knob of heater is in the OFF position.

4.Check all joints from gas meter (natural gas) or propane/LP supply to equipment shutoff valve (see Figure 16 or 17, page 15). Apply a commercial leak detection solution to all joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Light heater (see Operating Heater, page 18 [manually-controlled models] or page 21 [thermostatically-controlled models]). Check all other internal joints for leaks.

7.Turn off heater (see To Turn Off Gas to Appli- ance, page 20 [manually-controlled models] or page 22 [thermostatically-controlled models]).

INSTALLING LOGS, MODELS CGS2718PA, CGS2718NA, CGS3124PA, CGS3124NA, SGS3124PA AND SGS3124NA

WARNING:Failuretoposition thepartsinaccordancewiththese diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installa- tion and periodically thereafter, check to ensure that no flame comes in contact with any log. WiththeheatersettoHigh,check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contact- ing logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Locate pegs on the bottom of back log (#1). Slide these pegs into the holes in the grate base behind the burner (see Figure 18).

2.Locate the notches on the back of the front log (#2). Slide these notches over the tabs of the grate base (see Figure 19).

3.Locate the holes in the bottom of the left crossover log (#3). Place crossover log on pegs on left of the back log and front log (see Figure 20, page 17).

4.Locate the holes in the bottom of the right crossover log (#4). Place crossover log on pegs on right of the back log and front log (see Figure 20, page 17).

5.Add lava rock around base of heater if desired. Do not place lava rock on logs or burner.

Back Log (#1)

Hole

Figure 18 - Installing Back Log

Front

Log (#2)

Notch

Tabs of

Grate Base

Figure 19 - Installing Front Log

16

www.desatech.com

113101-01C

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 24 Variable MANUALLY-CONTROLLED Models Patent PendingTable of Contents Safety Information Product Identification Product Features Local CodesUnpacking AIR for Combustion VentilationProviding Adequate Ventilation Determining FRESH-AIR Flow for Fireplace LocationUnusually Tight Construction Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Check GAS TypeLog Size Side Wall Ceiling Minimum Firebox SizeFront Rear Minimum Noncombustible Material ClearancesMantel Clearances Log SetFloor Clearances Log SetInstalling Heater Base Installing Damper Clamp Accessory for Vented OperationAssembly Connecting to GAS Supply Installation Items NeededPointing Down NaturalTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Heater Gas Connections Installing Back LogInstallation Operating Heater What to do if YOU Smell GASLighting Instructions Slightly depress and turn control knob counVariable Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance STOP! Read the safety information, page 20, column Inspecting Burners Thermostat Control OperationPilot Flame Pattern Burner Primary AIR HolesODS/PILOT and Burner Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole Service Hints Technical ServiceReplacement Parts Troubleshooting Observed Problem Possible Cause RemedyODS/pilot lights but flame goes See Cleaning and Mainte Gas leak. See Warning Statement aboveOptional Positioning Thermostat Sensing Bulb For Masonry and FACTORY- Built Metal FireplaceSpecifications Accessories Parts CentralEquipment Shutoff Valve GA5010 Fireplace HoodIllustrated Parts Breakdown Parts List Variable MANUALLY-CONTROLLED Winchester OAK ModelsIllustrated Parts Breakdown THERMOSTATICALLY-CONTROLLED Royal English OAK Models Keep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS Fireplace

CGS2718PA, CGS2718NA, CGS3124PA, CGS3124NA, SGS3124PA, SGS3124NA,CLD3018PTA, CLD3018NTA, CLD3924NTB, CLD3924PTB specifications

The models Desa CGS2718PA, CGS2718NA, CGS3124PA, CGS3124NA, SGS3124PA, SGS3124NA, CLD3018PTA, CLD3018NTA, CLD3924NTB, and CLD3924PTB are part of a versatile range of consumer appliances that combine modern technology with practical design. Each model brings its unique set of features aimed at enhancing user experience while maintaining high performance and efficiency.

Starting with the CGS series, the CGS2718PA and CGS2718NA are known for their compact sizes, making them ideal for smaller spaces without compromising functionality. They offer advanced digital controls, providing users with precise temperature settings and easy operation. Both models feature a sleek design, available in contemporary finishes that complement modern kitchen aesthetics.

The CGS3124PA and CGS3124NA expand on these features, offering greater capacity and additional functionalities such as enhanced cooking modes. These models incorporate the latest multi-cooking technology, allowing users to steam, bake, and roast with ease. Their energy-efficient systems help reduce power consumption while delivering great performance.

In the SGS series, both SGS3124PA and SGS3124NA prioritize efficiency and durability. Their robust construction is designed to withstand the rigors of daily use, while their intuitive controls simplify operation. These models are equipped with smart sensors that monitor cooking conditions and adjust settings automatically, ensuring optimal results every time.

Moving to the CLD series, the CLD3018PTA and CLD3018NTA are designed for versatility, featuring multiple cooking settings that cater to diverse culinary needs. These models excel in user-friendly interfaces, making meal preparation accessible to everyone, from novice cooks to experienced chefs.

The CLD3924NTB and CLD3924PTB stand out with their larger capacity and advanced technology that includes self-cleaning options, programmable timers, and compatibility with smart home systems. This adds another layer of convenience to the cooking process, allowing users to plan meals according to their schedules.

Overall, these models offer a comprehensive approach to modern cooking with an emphasis on efficiency, ease of use, and stylish design. They not only meet the demands of everyday cooking but also enhance the overall experience in the kitchen, making them a valuable addition to any home.
Top Page Image Contents