Desa VVDA18R, VVSA24R Curing Logs, Optional Remote Operation, GWMS2 Wall Mounted Switch Optional

Page 14

® VENTED GAS LOGS

OPERATING

APPLIANCE

Continued

CURING LOGS

During the 2-3 hour appliance break-in period, you may detect an odor from the appliance as the various paints and com- pounds used in the manufacturing of this log set cure. This is a normal and tempo- rary situation that is not cause for alarm. However, you may want to provide extra ventilation to the room during this time.

To ensure proper curing of the logs:

•Ignite a 2" flame and maintain it for 1 hour.

•Burn the logs in consecutive 1 hour pe- riods raising the flame an additional 2" to full flame height for a total of three hours.

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased separately. Follow instruc- tions included with the remote control.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions.

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Slide the selector switch to the REMOTE position. NOTE: The burner may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burner on and off with the hand- held remote control unit.

IMPORTANT: Do not leave the se- lector switch in the REMOTE posi- tion when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 sec- onds to assure proper operation.

GHRC Operation:

2.Press the ON/OFF button to turn the burner on and off. When turning burner off, the pilot will remain lit.

GWMS2 WALL

MOUNTED SWITCH

(OPTIONAL)

This wall switch works just like the con- ventional light switch. Flip the switch up for on and down for off.

Note: Make sure that this switch is not in a position to be mistaken for a light switch. This may result in the log set being inad- vertently turned on without the proper precautions being taken. See installation instructions on page 11 of this manual.

14

901272

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Models VVSA18R What to do if YOU Smell GASFor Use with Log Sets VVDA24R, and VVDA30RSafety Information Vented GAS LogsProduct Identification Local Codes Product FeatureRemote Ready Safety VALVE/PILOT UnpackingUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Appliance Location Building Ventilation AIRVentilation Air From Inside Ventilation Air From OutdoorsVenting Specifications for Installation InstallationFlue Opening Specifications Check GAS TypeInstallation Items Needed Installing Damper ClampConnecting to GAS Supply Pressure Testing Gas Supply Piping SystemTest Pressures Equal To or Less Than 1/2 Psig Hearth KIT Assembly and InstallationKit Assembly Burner Inlet Fitting Adjusting Regulator Pressure For Propane/LP ConversionPropane/LP Gas Conversion No Optional Accessories Remote Control OptionsTesting Burner for Leaks Changing Pilot OrificeOperating Appliance Installing the Grate and LogsFor Your Safety Read Before Lighting Adding PAN MaterialTo Turn OFF GAS To Appliance Manual Lighting ProcedureLighting Instructions Shutting Off ApplianceOptional Remote Operation GWMS2 Wall Mounted Switch OptionalCuring Logs Ghrc OperationTroubleshooting Observed Problem Possible Cause RemedyClean pilot see Cleaning and Mainte Top Gas leak. See Warning statement atIllustrated Parts Breakdown Models VVSA18R VVSA24R, VVDA18R VVDA24R, and VVDA30RParts List LOG SET Models VSLR18, VSLR24, VDLCR18, VDLCR24, and VDLCR30 Parts List Accessories Cleaning and MaintenanceReplacement Parts 901272 Warranty Information International
Top Page Image Contents