Desa Dual Burner Premium Aged Split Oak Models, Dual Burner Biltmore Split Oak Models

Page 14

14

INSTALLATION

Installing Logs (Cont.)

INSTALLATION

Continued

Dual Burner Premium Aged Split Oak Models

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place the base of the middle log (#1) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 22). Make sure the front of the middle log is resting on the tabs of the grate base and the cut- out area is centered over the burner “U” bend.

2.Locate pins on the bottom of back log (#2). Slide these pins into the holes in the grate base behind the burner (see Figure 23).

3.Place crossover log (#3) onto the pin (right) on middle log (#1) and into the recess of the back log (#2). See Figure 24.

4.Locate the notches in the bottom of the front log (#4). Place the front log on the grate fingers. Make sure the notches of the front log line up with the grate fingers. See Figure 25.

5.With knot to right side, place smaller log piece (#5) over the pin on the left side of the middle log. The smaller log will rest on front log against the "knot" on the left. See Figure 26.

6.Place lava rock around base of heater if desired. Do not put lava rock on logs on burner.

Pin

Back Log (#2)

Crossover

Log (#3)

 

 

Hole in

 

 

Grate

 

Recess

Base

 

 

 

 

 

Pin

Burner

 

Figure 23 - Installing Back

Figure 24 - Installing Crossover

Log (#2)

Log (#3)

Front Log (#4)

Log Piece

 

 

(#5)

Notches

 

 

Pin

Middle Log (#1)

Grate Fingers

Tab

Burner

“U” Bend

U-Shaped

Slot

Figure 22 - Installing Middle Log (#1)

Figure 25 - Installing Front Log

Figure 26 - Installing Log Piece

(#4)

(#5)

Dual Burner Biltmore Split Oak Models

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically there- after, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs accord- ing to the log installation instructions in this manual. Flames contacting logs will create soot.

For..com

107123-01F

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Biltmore Split OAK, Seasonal OAK, Smoky Mountain OAK Logs OWNER’S Operation Installation ManualUnvented VENT-FREE Natural GAS LOG Heaters What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Local Codes Product Features AIR for Combustion and VentilationUnpacking Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationInstallation Minimum Firebox Size Log Front Rear Height Depth WidthIf Not Using Mantel Minimum Noncombustible Material ClearancesFloor Clearances Determining Minimum Mantel Clearance When Using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Area of Various Standard Round FluesConnecting to GAS Supply Attaching Flexible Gas Hose to Heater Gas RegulatorPressure Testing Gas Supply Piping system Checking GAS ConnectionsDual Burner Smoky Mountain Oak Models Installing LogsPressure Testing Heater Gas Connections Dual Burner Premium Aged Split Oak Models Dual Burner Biltmore Split Oak ModelsInstalling Rear Log Installing Crossover Log Single Burner Seasonal Oak ModelsLighting Instructions For Your Safety Read Before LightingOperating Heater To Turn OFF GAS To Appliance Manual Lighting ProcedureVariable Control Operation Shutting Off HeaterIgnitor Button Cleaning and Maintenance Inspecting BurnersModel Models SpecificationsLogs ModelTroubleshooting Observed Problem Possible Cause RemedyRefer to Air for Combustion and Venti Top Gas leak. See Warning statement at topOptional Positioning of Thermostat Sensing Bulb For Masonry and Factory-built Metal FireplaceIllustrated Parts Breakdown Parts List Variable Manually-ControlledCGD3018NT CGD3924NT CGD3930NT CGD3018NT CGD3924NT CGD3930NT CCL3018NT Thermostatically-Controlled Biltmore Split Oak ModelCCL3018NT CCL3924NT, CCL3930NTA CCL3924NT CCL3930NTA Variable Manually-Controlled Seasonal Oak Models Variable Manually-Controlled Mountain Oak Models CRL2718N CRL3124NTechnical Service Replacement PartsService Hints AccessoriesOwners Registration Form Postage Required Parts Central Warranty Information

CGD3018N, CGD3924N, CGD3930N, CRL2718N, CCL3924N, CRL3124N, CCL3018N, CGD3924NT, CGD3018NT, CCL3924NT, CGD3930NT, CCL3018NT, CCL3930NTA specifications

The Desa product line, consisting of models CGD3018N, CGD3924N, CGD3930N, CRL2718N, CCL3924N, CRL3124N, CCL3018N, CGD3924NT, CGD3018NT, CCL3924NT, CGD3930NT, CCL3018NT, and CCL3930NTA, offers a wide range of heating solutions designed to tackle diverse customer needs. These models are distinctive for their durability, efficiency, and user-friendly designs.

Among the standout features of the Desa CGD series, models such as CGD3018N and CGD3924N integrate advanced combustion technologies that maximize fuel efficiency while minimizing emissions. This ensures that users enjoy a cleaner burn and reduced operational costs. The CGD3930N model boasts a higher output, making it suitable for larger spaces, while maintaining a compact design to fit various room layouts.

The CRL series, including CRL2718N and CRL3124N, emphasizes flexibility and ease of installation. These units employ a direct venting system that allows for efficient heat distribution without the need for extensive ductwork. The CCL models, such as CCL3924N and CCL3018N, are designed with aesthetics in mind. They feature sleek styles that blend seamlessly into modern home decors, all while delivering reliable heating performance.

The NT variants, such as CGD3924NT and CCL3924NT, introduce smart technology integration, allowing users to control their heating solutions remotely via smartphone applications. This feature ensures maximum convenience and adaptability to varying user preferences or schedules.

In terms of safety, all models are equipped with built-in features to prevent overheating and ensure stable operation. Additionally, many units incorporate easy-to-use thermostats and adjustable flame settings, providing users with greater control over their indoor climate.

Overall, the Desa models combine innovation with practicality, making them a preferred choice for consumers looking for efficient, stylish, and reliable heating solutions. With a variety of products catering to different preferences and requirements, Desa continues to be a leader in the heating industry, ensuring comfort and satisfaction for all users.
Top Page Image Contents