Bradford-White Corp PDV80T300, D80T725, D65T625, PDV100S150, PDV100S250, PDV100T360 Setpoint Flashes

Page 16

Step 2: Press the “Set” button to enter the setting mode. “Setpoint” will flash in the water heater display.

°F setpoint

idle

Status Operational

SELECTSET

Step 3: To raise the temperature setpoint, press the “Temperature Up” button until the desired temperature is shown on the water heater display.

NOTICE

The maximum temperature that can be set in the Water Heater Display is limited to the “Max Setpoint” described previously. To change the “Max Setpoint”, refer to the procedure “To Change the Maximum Setpoint Limit…" described previously under “Accessing the Service Mode on the Water Heater Display”.

WARNING

Setting the water temperature to the maximum set point can result in scalding hot water delivered to the faucets. It is highly recommended that the maximum setpoint be adjusted to the lowest temperature possible for the needs of the installation. Make sure the water heater control display is not in a public area that can result in the temperature settings being improperly adjusted.

°F

setpoint

%

 

idle

 

 

Status Operational

 

 

SELECT

SET

 

Step 4: To lower the temperature setpoint, press the “Temperature Down” button until the desired temperature is shown on the water heater display.

"Setpoint" Flashes

°F setpoint

idle

Status Operational

SELECTSET

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Service Manual Table of Contents Features of PDV-S Model Series Features of PDV-T Model SeriesFeatures of Induced Draft Models Features of Honeywell Integrated Controls SystemTools Required for Service Specifications Sequence of Operation Troubleshooting Verify Primary and Secondary voltage at the control boardError code #63 on display. See Main Burner short Pressing Select button will change display to next mode Max Setpoint Display/Change Setpoint Display/Change Software Version Display only SET ExitingSELECTServiceSETMode Display of Water TemperatureTo Display and Change Temperature Setpoint To Display Flame Sense Current of the Pilot Flame SensorSetpoint Flashes Idle Status Operational Select SET Error Codes and Error History Display Error Code HistoryTo view previous error codes ExitingSELECTServiceSETMode Error Code Definitions Resetting Error Codes in Hard Lockout Condition Service Procedure PDV24-I Unplug or disconnect electrical power to the water heaterService Procedure PDV24-I Upper Sensor Lower SensorService Procedure PDV23-II Service Procedure PDV24-II Service Procedure PDV24-II Service Procedure PDV24-III ConditionCondition Error code 57 Flame Rod Shorted To Ground Probe Service Procedure PDV24-IV To control boardCorrect improper venting condition Manifold Pressure Port Service Procedure PDV24-V PDV S&T ModelsPDV S&T Models PDV S&T Models Induced Draft Models Main Burner RemovalPilot Burner Removal Pilot Burner InspectionControl board replacement Service Procedure PDV24-VIRemove lower sensor Service Procedure PDV24-VII Service Procedure PDV24-VIII PDV-S PDV S PDV-S PDV-T PDV T PDV-T Induced Draft Models Induced Draft Models Induced Draft Models BTU/H CO2ECO GFI

PDV80T300, PDV100S150, PDV100T360, PDV80S150, D65T625 specifications

Bradford-White Corporation is renowned for its quality water heating solutions, with a diverse range of products designed to meet various residential and commercial needs. Among their stellar offerings are the D80T725, PDV100S200, PDV100S250, PDV80S250, and PDV802200 models, each equipped with advanced technologies and features that set them apart in the market.

The D80T725 is an innovative 80-gallon water heater that employs a powerful 75,000 BTU burner, ensuring rapid water heating for larger households. One of its key features is the Defender Safety System, which provides exceptional protection against potential hazards. The advanced electronic control system enhances efficiency and reliability, making it an ideal choice for energy-conscious consumers. Additionally, the tank's unique insulation helps maintain water temperature longer, reducing energy costs.

Moving to the PDV series, the PDV100S200 and PDV100S250 are dynamic, direct vent gas water heaters with capacities of 100 gallons and impressive BTU inputs. These models utilize a proper venting system that draws air from outside, ensuring that indoor air quality remains uncompromised. Both models feature Bradford-White's patented hydrojet total performance system, improving heat transfer by minimizing sediment buildup. This technology prolongs the lifespan of the unit while maximizing energy efficiency.

The PDV80S250, like its PDV counterparts, also utilizes direct venting technology for enhanced safety and efficiency. With an 80-gallon capacity and a robust 250,000 BTU input, this model is designed for businesses and larger households requiring significant hot water availability. The use of cutting-edge insulation technology in these models reduces standby heat loss, which translates to substantial savings on energy bills.

Lastly, the PDV802200 stands out with similar advanced features but offers a higher capacity of 80 gallons, making it a perfect solution for commercial applications. It strikes a balance between performance and reliability, ensuring consistent hot water delivery even during peak demand. The integration of robust safety features and user-friendly controls make it easy for facility managers to operate and maintain.

In summary, whether you opt for the D80T725 or one of the PDV models, you can expect a blend of performance, efficiency, and advanced technology. Bradford-White's commitment to quality and innovation ensures that each product meets the demands of modern consumers, making them a leading choice in the water heating industry.
Top Page Image Contents