Bradford-White Corp PDV80S150, D80T725, D65T625 Induced Draft Models, Main Burner Removal

Page 38

SERVICE PROCEDURE PDV24-V

Main Burner & Pilot

Removal and Inspection

WARNING

Water Heater components may be HOT when performing the following steps in this

procedure. Take necessary precaution to prevent personal injury.

INDUCED DRAFT MODELS

Gas Valve

Control Knob

Main Burner Removal

Step 1.

Disconnect (un-plug) water heater from

Gas Valve

Wire Leads

 

electrical supply.

 

Step 2.

Turn “OFF” gas supply to water heater.

 

Step 3.

Rotate gas valve control knob to the “OFF” position

 

(see photos at right).

 

Step 4.

Disconnect Gas supply line from the gas valve.

Step 5.

Disconnect wire leads from gas valve

Pilot Flame Sense

 

(see photos at right).

 

Wire (White)

 

 

Step 6.

Disconnect white flame sense wire & orange ignition

 

wire from Control Board (see photos at right).

Step 7.

Remove the two burner rack mounting screws (see photos).

Step 8.

Slide complete burner rack out from water heater

 

(see photos below).

 

Step 9.

To install burner, reverse above procedure.

 

Step 10.

Check for gas leaks and verify proper operation.

Burner Rack

Mounting

Screw

Pilot spark wire

(Orange)

Pilot Draft

Burner RackShield

Mounting

Screw

38

Image 38
Contents Service Manual Table of Contents Features of Induced Draft Models Features of PDV-S Model SeriesFeatures of PDV-T Model Series Features of Honeywell Integrated Controls SystemTools Required for Service Specifications Sequence of Operation Troubleshooting Verify Primary and Secondary voltage at the control boardError code #63 on display. See Main Burner short Pressing Select button will change display to next mode Max Setpoint Display/Change Setpoint Display/Change Software Version Display only SET ExitingSELECTServiceSETMode Display of Water TemperatureTo Display and Change Temperature Setpoint To Display Flame Sense Current of the Pilot Flame SensorSetpoint Flashes Idle Status Operational Select SET Error Codes and Error History Display Error Code HistoryTo view previous error codes ExitingSELECTServiceSETMode Error Code Definitions Resetting Error Codes in Hard Lockout Condition Service Procedure PDV24-I Unplug or disconnect electrical power to the water heaterService Procedure PDV24-I Upper Sensor Lower SensorService Procedure PDV23-II Service Procedure PDV24-II Service Procedure PDV24-II Service Procedure PDV24-III ConditionCondition Error code 57 Flame Rod Shorted To Ground Probe Service Procedure PDV24-IV To control boardCorrect improper venting condition Manifold Pressure Port Service Procedure PDV24-V PDV S&T ModelsPDV S&T Models PDV S&T Models Induced Draft Models Main Burner RemovalPilot Burner Removal Pilot Burner InspectionRemove lower sensor Service Procedure PDV24-VIControl board replacement Service Procedure PDV24-VII Service Procedure PDV24-VIII PDV-S PDV S PDV-S PDV-T PDV T PDV-T Induced Draft Models Induced Draft Models Induced Draft Models ECO BTU/HCO2 GFI

PDV80T300, PDV100S150, PDV100T360, PDV80S150, D65T625 specifications

Bradford-White Corporation is renowned for its quality water heating solutions, with a diverse range of products designed to meet various residential and commercial needs. Among their stellar offerings are the D80T725, PDV100S200, PDV100S250, PDV80S250, and PDV802200 models, each equipped with advanced technologies and features that set them apart in the market.

The D80T725 is an innovative 80-gallon water heater that employs a powerful 75,000 BTU burner, ensuring rapid water heating for larger households. One of its key features is the Defender Safety System, which provides exceptional protection against potential hazards. The advanced electronic control system enhances efficiency and reliability, making it an ideal choice for energy-conscious consumers. Additionally, the tank's unique insulation helps maintain water temperature longer, reducing energy costs.

Moving to the PDV series, the PDV100S200 and PDV100S250 are dynamic, direct vent gas water heaters with capacities of 100 gallons and impressive BTU inputs. These models utilize a proper venting system that draws air from outside, ensuring that indoor air quality remains uncompromised. Both models feature Bradford-White's patented hydrojet total performance system, improving heat transfer by minimizing sediment buildup. This technology prolongs the lifespan of the unit while maximizing energy efficiency.

The PDV80S250, like its PDV counterparts, also utilizes direct venting technology for enhanced safety and efficiency. With an 80-gallon capacity and a robust 250,000 BTU input, this model is designed for businesses and larger households requiring significant hot water availability. The use of cutting-edge insulation technology in these models reduces standby heat loss, which translates to substantial savings on energy bills.

Lastly, the PDV802200 stands out with similar advanced features but offers a higher capacity of 80 gallons, making it a perfect solution for commercial applications. It strikes a balance between performance and reliability, ensuring consistent hot water delivery even during peak demand. The integration of robust safety features and user-friendly controls make it easy for facility managers to operate and maintain.

In summary, whether you opt for the D80T725 or one of the PDV models, you can expect a blend of performance, efficiency, and advanced technology. Bradford-White's commitment to quality and innovation ensures that each product meets the demands of modern consumers, making them a leading choice in the water heating industry.