Bradford-White Corp IGE-199C, IGE-199R Remote Temperature Controls, Residential Models

Page 25

REMOTE TEMPERATURE CONTROLS

The supplied Remote Main Control allows the customer to control the hot water supply temperature and will display certain fault codes in the event the water heater needs servicing. If used without the Remote Main Control connected, the residential models (IGE-199R-10N,10X) have a fixed temperature setting of 120°F and the commercial models (IGE-199C-5N, 5X) have a fixed temperature setting of 140°F.

Residential Models:

The Main Remote Control inside the carton is intended for installation in the kitchen, utility, or laundry area of a home. The adjustment range for the main control is 96-160°F. This is the only control capable of temperature setpoints greater than 120°F.

DANGER

Hotter water increases the risk of scald injury. Scalding may occur within 5 seconds at a temperature setting of 135°F (57°C). To protect against hot water injury, install a mixing valve in the water system. This valve will reduce point of discharge temperature by mixing cold and hot water in branch water lines. A licensed plumbing professional or local plumbing authority should be consulted.

NOTICE

This water heater is equipped with an energy cut out device to prevent overheating. Should overheating occur or the gas supply fail to shut off, turn off the manual gas control valve to the appliance and call a qualified service agency.

CAUTION

This water heater, when set at a lower temperature setting is not capable of producing hot water of sufficient temperature for sanitizing purposes.

Always check water temperature by hand before entering the shower or bath. The temperature may have been changed.

Test the temperature of the water with your hand or elbow before placing a child in the bath or shower. Do not leave a child or an infirm person in the bath unsupervised.

In addition, residential models may have one (1) optional Bath Control (P/N: 239-44507-00) and one (1)

Secondary Bath Control (P/N: 239-44508-00) installed in bathrooms to control the temperature for showers and sinks. Both of these controls have setpoint ranges of 96-120°F. When these controls are used, depressing the Priority Button will override the Main Remote Control and display the setpoint of the Bath Control in use. Both the remote Bath Controls and the Main Remote Control will display fault codes in the event the water heater needs service.

NOTICE

Only one of each type of remote temperature control can be connected to one residential EVERHOT→ water heater (i.e., Installations with two Main Controls, or two Bath Controls, or two Secondary Bath Controls will not function properly.

Before installing the remote controls, determine the most convenient locations(s). When deciding on the best location for the remote controls, please consider the following items:

1.Place the controls out of reach of small children.

2.Avoid locations where the control(s) will become hot, such as over the stove, near the oven, or other heat sources.

3.Avoid direct sunlight. (The digital readout can be difficult to read in direct sunlight).

4.Avoid areas where the remote can be splashed with cooking water, oil, or sauce.

5.The remote control operates with low voltage, 12 volts DC.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents IGE-199R and IGE-199C Model Series Read Carefully Section I Important InformationPage Do not Operate the Appliance Until the Leakage is Corrected Table of Contents IGE-199R-10X Section II SpecificationsEVERHOT→ IGE Model Series Dimensions Section III General Information FeaturesDo not Operate the Appliance Until the Leakage is Corrected Section IV Installation InstructionsWater Heater Location UnpackingReference Description Minimum Distance Inches cm Build Opening Clearances FigRemove Carton Mount Water Heater on the WallSection V Water Connections Lime Condition Warning SignalWater Quality Instructions for ConnectionsPage Recommended Piping for a Basic Installation Drain Solenoid Piping Fig Recommended Piping for Power Failure Freeze ProtectionRecommended Piping for a Circulation System Page Pressure Relief Valve Section VI GAS Connections Never USE a Match or Open Flame for TestingGAS Meter Size -NATURALGAS only Initial Operation and Testing Installer onlyGAS Pressure Regulation Page Section VII Electrical Connections Wiring Diagram Wiring Diagram Schematic Residential Models Remote Temperature ControlsPage Commercial Models Initial Operation and Testing of Controls Installer only Control Wiring Connections Inside Water HeaterTo Fill the Water Heater Section Viii Operating InstructionsSequence of Operation To Turn OFF GAS to the Appliance Lighting Instructions For Your Safety Read Before OperatingManual Gas Valve Fig Residential Models see Figure Turning OFF the Water Heater for AN Extended Period of TimeCommercial Models see Figure Main or Bath Control For Residential Models FigMain Control for Commercial Models Fig First AID for Scalds Approximate TIME/TEMPERATURE Relationships in ScaldsError Messages on Remote Temperature Control Display Section IX Maintenance Burner Flame Appearance Fig Page Lime Scale Flushing Diagram Fig Schematic Diagram of Internal Parts Section X Parts List Exploded View Internal Components Exploded View Internal Components Exploded View Electrical Parts List Anti-Frost Heater Clip

IGE-199R, IGE-199C specifications

Bradford-White Corp is renowned for its commitment to high-quality water heating and storage solutions, and its IGE-199C and IGE-199R models are prime examples of their innovation in the domain of gas-fired water heaters. These units are designed specifically for commercial applications, catering to restaurants, hotels, and other establishments that require efficient and reliable hot water supply systems.

One of the standout features of the IGE-199C and IGE-199R models is their energy efficiency. Both models utilize advanced technology to ensure minimized energy consumption while maximizing performance. They are equipped with a robust gas burner that delivers rapid heating capabilities, making them ideal for businesses with high demand for hot water. With an Energy Factor rating that meets or exceeds industry standards, users can expect lower operational costs, contributing to overall energy savings.

The IGE-199C is a compact, natural gas-powered unit, engineered for easy installation and integration. Its unique design features a built-in venting system that simplifies the setup process, making it suitable for retrofitting into existing systems. Meanwhile, the IGE-199R model offers similar performance with added versatility, as it can operate on either natural gas or propane, providing flexibility for various installation requirements. Both models are equipped with a powerful heat exchanger that enhances heat transfer efficiency, ensuring consistent delivery of hot water.

Safety and reliability are also central to the IGE-199C and IGE-199R designs. Each unit is fitted with multiple safety features, including high-temperature limit switches and an integrated drain valve, ensuring safe operation under all conditions. The durable construction of these water heaters, with heavy-duty commercial-grade materials, enhances longevity while reducing the likelihood of maintenance issues.

Another notable characteristic is their user-friendly control systems, enabling easy adjustments to temperature settings and monitoring of performance metrics. This ensures that operators can maintain optimal performance levels without extensive training or technical knowledge.

In summary, the Bradford-White IGE-199C and IGE-199R models are state-of-the-art gas-fired water heaters that combine efficiency, safety, and reliability. Their innovative features and technologies make them ideal for demanding commercial applications, providing businesses with an effective solution for their hot water needs. With their focus on durability and performance, these models exemplify Bradford-White's dedication to excellence in water heating technology.
Top Page Image Contents