Bradford-White Corp IGE-199C, IGE-199R instruction manual Commercial Models

Page 27

WARNING

Do not attempt to connect the remote controls with the power on to the water heater. There are 120 volt terminals and wiring next to the remote control connections inside the unit. All servicing and wiring must be performed by a certified installer.

9.Thread the cable through the access hole at the base of the water heater and connect the wires to the control terminals on the right hand side of the PCB. See control wiring illustration (fig. 8).

10.Secure the control cable using the clamp provided in the control compartment.

11.Replace the plastic cover over the PCB terminals and then replace the front control panel of the water heater.

Commercial Models:

The Main Remote Control (inside water heater carton) is intended for installation in a convenient location near where most of the hot water will be used. The adjustment range for this control for commercial models only is 96-180°F. If the water heater is used without the Main Control connected, then the factory default temperature setting is 140°F. In addition, the control will display fault codes in the event the water heater needs service. Only one remote control may be used on commercial models.

WARNING

When the Remote Control is used in public use applications, it must be installed in a location where it cannot be adjusted by the public (i.e., a maintenance room or manager’s office). Unauthorized adjustments may result in scalding conditions.

NOTICE

Only one remote temperature control can be connected to one Commercial EVERHOT→ water heater (i.e., Installations with two controls will not function properly).

Before installing the remote control, determine the most convenient location. When deciding on the best location for the remote control, please consider the following items:

1.Place the control out of reach of small children.

2.Avoid locations that may allow adjustment by unauthorized personnel (see above warning).

3.Avoid locations where the control will become hot, such as over the stove, near the oven, or other heat sources.

4.Avoid direct sunlight. (The digital readout can be difficult to read in direct sunlight).

5.Avoid areas where the remote can be splashed with cooking water, oil, or sauce.

6.The remote control operates with low voltage, 12 volts DC

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents IGE-199R and IGE-199C Model Series Read Carefully Section I Important InformationPage Do not Operate the Appliance Until the Leakage is Corrected Table of Contents IGE-199R-10X Section II SpecificationsEVERHOT→ IGE Model Series Dimensions Section III General Information FeaturesDo not Operate the Appliance Until the Leakage is Corrected Section IV Installation InstructionsWater Heater Location UnpackingMount Water Heater on the Wall Build Opening Clearances FigReference Description Minimum Distance Inches cm Remove CartonInstructions for Connections Lime Condition Warning SignalSection V Water Connections Water QualityPage Recommended Piping for a Basic Installation Drain Solenoid Piping Fig Recommended Piping for Power Failure Freeze ProtectionRecommended Piping for a Circulation System Page Pressure Relief Valve Section VI GAS Connections Never USE a Match or Open Flame for TestingInitial Operation and Testing Installer only GAS Meter Size -NATURALGAS onlyGAS Pressure Regulation Page Section VII Electrical Connections Wiring Diagram Wiring Diagram Schematic Residential Models Remote Temperature ControlsPage Commercial Models Initial Operation and Testing of Controls Installer only Control Wiring Connections Inside Water HeaterSection Viii Operating Instructions To Fill the Water HeaterSequence of Operation Lighting Instructions For Your Safety Read Before Operating To Turn OFF GAS to the ApplianceManual Gas Valve Fig Residential Models see Figure Turning OFF the Water Heater for AN Extended Period of TimeCommercial Models see Figure Main or Bath Control For Residential Models FigMain Control for Commercial Models Fig First AID for Scalds Approximate TIME/TEMPERATURE Relationships in ScaldsError Messages on Remote Temperature Control Display Section IX Maintenance Burner Flame Appearance Fig Page Lime Scale Flushing Diagram Fig Schematic Diagram of Internal Parts Section X Parts List Exploded View Internal Components Exploded View Internal Components Exploded View Electrical Parts List Anti-Frost Heater Clip

IGE-199R, IGE-199C specifications

Bradford-White Corp is renowned for its commitment to high-quality water heating and storage solutions, and its IGE-199C and IGE-199R models are prime examples of their innovation in the domain of gas-fired water heaters. These units are designed specifically for commercial applications, catering to restaurants, hotels, and other establishments that require efficient and reliable hot water supply systems.

One of the standout features of the IGE-199C and IGE-199R models is their energy efficiency. Both models utilize advanced technology to ensure minimized energy consumption while maximizing performance. They are equipped with a robust gas burner that delivers rapid heating capabilities, making them ideal for businesses with high demand for hot water. With an Energy Factor rating that meets or exceeds industry standards, users can expect lower operational costs, contributing to overall energy savings.

The IGE-199C is a compact, natural gas-powered unit, engineered for easy installation and integration. Its unique design features a built-in venting system that simplifies the setup process, making it suitable for retrofitting into existing systems. Meanwhile, the IGE-199R model offers similar performance with added versatility, as it can operate on either natural gas or propane, providing flexibility for various installation requirements. Both models are equipped with a powerful heat exchanger that enhances heat transfer efficiency, ensuring consistent delivery of hot water.

Safety and reliability are also central to the IGE-199C and IGE-199R designs. Each unit is fitted with multiple safety features, including high-temperature limit switches and an integrated drain valve, ensuring safe operation under all conditions. The durable construction of these water heaters, with heavy-duty commercial-grade materials, enhances longevity while reducing the likelihood of maintenance issues.

Another notable characteristic is their user-friendly control systems, enabling easy adjustments to temperature settings and monitoring of performance metrics. This ensures that operators can maintain optimal performance levels without extensive training or technical knowledge.

In summary, the Bradford-White IGE-199C and IGE-199R models are state-of-the-art gas-fired water heaters that combine efficiency, safety, and reliability. Their innovative features and technologies make them ideal for demanding commercial applications, providing businesses with an effective solution for their hot water needs. With their focus on durability and performance, these models exemplify Bradford-White's dedication to excellence in water heating technology.
Top Page Image Contents