A.O. Smith Water Heater installation instructions Draft Hood Installation, PER Open

Page 13

GABLE VENT

 

j

TO OUTDOORS

 

 

 

 

 

 

ALTERNATIVE

 

 

INSTALLABOVE

OPENING

 

 

 

 

 

INSULATION

LOCATION

 

 

 

CONFINED

 

 

 

 

1SQ. INCH

OUTLET

 

CONFINED

 

 

PER3000 BTUH

 

 

AIR

TO

 

 

 

 

SPACE

 

ATTIC

1

SQ.

 

 

 

INCH

PER

 

 

 

4000

BTUH

 

ALTERNATE

 

AIR FROM

AIR

INLET

 

 

 

1 SQ.

INCH

PER

 

OPEN

_1_

4000 BTUH

 

FOUNDATION

"_

 

 

 

 

VENT

 

ALL

AIR

FROM OUTDOORS:

INLET

AIR FROM VENTILATED

CRAWL

SPACE/OUTLET

AIR TO

VENTILATED

ATTIC

FIGURE 6.

GABLE VENT TO OUTDOORS

_"INSTALL ABOVE

INSULATION

OUTLET AIR _TO ATTIC

1 SQ. INCH PER 4000

BTUH

INLET AIR DUCT 1 SQ. INCH PER 4000 BTUH

12" MAXIMUM

ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC

FIGURE 7.

2000 BTUH

CONFINED

SPACE

1 SQ. INCH PER

2000 BTUH

ALL AIR FROM OUTDOORS USING HORIZONTAL DUCTS

ALL AIR FROM OUTDOORS - USING A SINGLE PERMANENT OPENING

FIGURE 8B.

Vent Pipe System

This water heater uses a non-direct, single-pipe vent

system to remove exhaust gases created by the burning of fossil fuels. Air for combustion is taken from the immediate

water heater location or is ducted in from the outside (see "Combustion Air Supply and Ventilation").

This water heater must be properly vented for the removal of exhaust gases to the outside atmosphere. Correct

r'',,,,installation of the vent pipe system is mandatory for the proper and efficient operation of this water heater and is

an important factor in the life of the unit.

The vent pipe must be installed according to all local and state codes or, in the absence of local and state codes, the "National Fuel Gas Code", ANSI Z223.1(NFPA 54)-current edition. The vent pipe installation must not be obstructed so as to prevent the removal of exhaust gases to the outside atmosphere.

IMPORTANT: The use of vent dampers is not recommended by the manufacturer of this water heater. Although some vent dampers are certified by CSA International, this certification applies to the vent damper device only and does not mean they are certified for use on this water heater.

U.L. recognized fuel gas and carbon monoxide (CO) detectors are recommended in all applications and should be installed using the manufacturer's instructions and local codes, rules, or regulations.

IMPORTANT: If you lack the necessary skills required to properly install this venting system, you should not proceed, but get help from a qualified technician.

Draft Hood Installation

L SCREWS (FOUR PROVIDED)

b_I--DRAFT HOOD

SLDT----\ X-- AC ETTDP' --SLDT

INSTALL THE DRAFT HOOD WITH

THE FOUR SCREWS PROVIDED.

FIGURE 8A.

FIGURE 9

13

Image 13
Contents Smith InstallerWater Important Definitions Fire or Explosion Harzard Improper installation and use may result in property damageFire Hazard GET to Know Your Water Heater GAS Models Consumer Information Important Information About This Water HeaterConsumer Responsibilities Site Location Location RequirementsPmpey Damage Hazard Clearances and AccessibilityGas Pressure Gas Pressure TestingGas Requirements Gas PipingExplosion Hazard LP Gas OnlyConfined Space Unconfined SpaceCarbon Monoxide Warning RoomAll Air from Outdoors All Air from Inside the BuildingLouvers and Grilles PER Open Draft Hood InstallationVent Pipe Size Vent ConnectorsChimney Connection MA,NTA,N\ Piping InstallationClosed System/Thermal Expansion Propey Damage HazardTemperature & Pressure Relief Valve Temperature and Pressure Relief Valve Explosion HarzardRelief Valve and Pipe Insulation Some Models Combination Space Heating/Potable Water SystemAIR Solar InstallationWater System Piping Vent Pipe SystemGas Supply and Piping Before Lighting InstructionsChecking the Draft ForyoursafetyreadbeforelightingToturnoffgastoappliance Burn HazardBurner Flames Water Temperature RegulationEmergency Shut Down White Rodgers ValvesProperty Damage Hazard Operational ConditionsCondensation Anode Rod/Water Odor Routine Preventive MaintenanceDraining and Flushing Removing the Burner from the Manifold/ Burner Assembly Replacement PartsManualrelief ThermalReplacing the Thermocouple Replacing the Pilot/Pilot Tube AssemblyExternal Inspection & Cleaning of the Base-Ring Filter Replacing the Manifold/Burner AssemblyCleaning the Combustion Chamber and Flame-arrestor Piezoelectric Igniter System Testing the Igniter SystemRemoving and Replacing the Gas Control Valve/Thermostat Possible Causes FVlR System Operational ChecklistThermostat set too high ProblemYES Repair Parts List Listed Parts Kits and Illustrations Page Conditions and Exceptions Limited Residential GAS WarrantyInstallation Information Claim ProcedureLimitation on Implied Warranties Disclaimers

Water Heater specifications

A.O. Smith is a renowned name in the water heating industry, celebrated for its commitment to innovation, quality, and efficiency. Their water heaters are designed to cater to a wide variety of needs, making them suitable for both residential and commercial applications. The main features of A.O. Smith water heaters are tailored to ensure optimal performance, convenience, and reliability.

One of the standout characteristics of A.O. Smith water heaters is their impressive energy efficiency. Many models are equipped with advanced insulation technologies that minimize heat loss, allowing users to save on energy bills while ensuring a consistent supply of hot water. The introduction of high-efficiency gas burners and electric heating elements enhances their energy utilization, which is reflected in their excellent Energy Factor ratings.

A.O. Smith also incorporates smart technology in its water heaters. Many models feature integrated Wi-Fi connectivity, allowing homeowners to monitor and control their water heating system remotely via a smartphone app. This capability enables users to adjust temperature settings, receive maintenance alerts, and track energy usage, providing a new level of convenience and control.

Durability is another hallmark of A.O. Smith water heaters. Constructed with high-quality materials, these units often feature a glass-lined tank that enhances corrosion resistance. Additionally, many models are designed with a robust anode rod that helps prevent rusting, extending the lifespan of the heater and ensuring dependable service for years to come.

Safety features are also a priority for A.O. Smith. Many water heaters come equipped with advanced safety mechanisms, such as automatic shut-off valves, temperature controls, and flame failure detection systems, ensuring safe operation and reducing the risk of accidents.

Different models are available to suit varying space requirements and preferences. A.O. Smith produces traditional tank water heaters as well as modern tankless options, which provide endless hot water on demand, making them ideal for homes needing high hot water consumption. Their versatility guarantees that customers can find the perfect solution tailored to their specific needs.

In conclusion, A.O. Smith water heaters represent a blend of innovation, efficiency, durability, and safety. With various models available that cater to different heating needs and preferences, A.O. Smith continues to remain a trusted choice for consumers seeking reliable hot water solutions.