Genie M-4500, M-4700 Control Panel, SET the Adjustments, To Make or Change ANY Adjustment

Page 18

8-17. CONTROL PANEL

The control panel is located under the control panel cover.

Open the control panel by slightly pulling on the cover cutout, then allowing the cover to drop open. The hinges enable the cover to remain in place while you set

the adjustments.

On control panel you will find 3 buttons labeled “P”, “+”, and “–” which allows you to set all the adjustments of your opener and a circular LED display with 8 numbered icons which shows useful status information regarding the opener and its function. See Fig. 38, 38A.

LEDs #1, #3, and #5 are used when setting the adjustments or for troubleshooting, should a problem ever occur with your opener. See section “8-18. Setting The Adjustments” on p. 18, and section 18. Troubleshooting” on p. 29 for more information.

NOTE: When viewing control panel and setting the adjust- ments, stand below the opener and face the garage door. Then look up at the display. This way you will easily be able to see both the display and the door.

8-18. SET THE ADJUSTMENTS

Any adjustment can be made at any time using these 3 buttons: “+“, “–”, and “P”. However, it is easiest during initial installation to follow the order shown below. Before beginning, install battery in your transmitter.

See Fig. 47, p. 22.

Fig. 37

Rail

Cutout

Control Panel

Hinges

Control Panel

Cover

 

 

Opener Power

 

 

Head

Fig. 38

LED Display

Adjustment Buttons

The adjustments that can be made are: Open Travel Limit, Close Travel Limit, Maximum Opening Force, Maximum Closing Force, and Transmitter Programming.

HANDY NOTE: If you follow the following steps, you will notice that when making the adjustments, and if no changes are needed at any particular stage, you can keep the current information and ”skip“ over a specific adjustment by pressing the “P” button once. This is useful to know if you want to change only one setting, without changing any of the other adjustments. Simply enter the adjustment mode by pressing and holding the “P” button for approximately

2 seconds, then press and release “P” repeatedly until your particular adjustment is reached. This bypasses the unneeded adjustments, and takes you right to the adjustment you want. When your adjustment or setting is complete, simply press “P” as many times as needed to bypass the remaining steps and exit out of the program, returning the opener to normal mode.

TO MAKE OR CHANGE ANY ADJUSTMENT:

Press and hold the “P” button for approximately 2 seconds. When all LEDs illuminate and LED #2 begins to blink, release the button. You are now ready to set or change the desired adjustment.

Fig. 38A

Key to Icons and

Corresponding LEDs:

LED #2 ■ Lights up when door is in fully opened position.

LED #4 ■ Lights up when door is in fully closed position.

LED #6 ■ Flashes when obstruction is detected, door reverses, or other problem occurs. See section “18. Troubleshooting” on p. 30 for more information.

LED #7 ■ Lights up when opener is receiving a signal from wall control or pushbutton.

■Flashes rapidly when opener is receiving a signal from remote transmitter or keyless entry system.

■Flashes slowly when vacation/ lock mode is active.

LED #8 ■ Lights up when power is on.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Digital Intelligence for the Garage M-4500 Tools Advanced Features Important Safety InformationIntroduction Tools Garage and DoorSectional Door One-Piece DoorOpener Package Contents Important Installation Instructions Read and Follow ALL Installation InstructionsInstallation Steps Install Header BracketMeasure and Mark Door Area Install Door Bracket to Door For Sectional DoorsFor ONE-PIECE Doors Attach Rail to Opener Head Additional Step for ONE-PIECE Doors onlySectional Doors and ONE-PIECE Doors with Track Attach Rail to Header BracketPosition Opener for Mounting ONE-PIECE Doors Without TrackMount Opener to Ceiling Sectional Doors Connect ARM to Door and TrolleyCheck Emergency Release ALL ONE-PIECE DoorsMounting Photo EYE Directly to Wall Install Photo EYE Safety SystemInstall Wall Control Panel Mounting Photo EYE to BracketConnecting Wires to Powerhead Doorbell-Type Pushbutton4700 Install Light Bulbs and LensesAntenna Wire Installation 40MHZ 4500Connect to Power Permanent Wiring ConnectionModular Receiver Control Panel SET the AdjustmentsTo Make or Change ANY Adjustment Key to Icons Corresponding LEDsUP Force Fig Open Travel Limit FigClose Travel Limit Fig Down Force FigAlign and Test Photo Eyes Test Safety ReversalSafety Test AlignmentImportant Safety Instructions Apply Labels to Inside of GarageMultiple Transmitters TransmittersTransmitter Mounting Code ChangeOperation of Your Opener Homelink TransceiverTension Adjustment Rail Length AdjustmentBelt Rail Assembly Chain Rail AssemblySystem Parts Lamp Lens Power Head Assembly System Parts cont‘dAccessories Midi & Mini TransmittersHaving a PROBLEM? Situation Likely Cause and SolutionTroubleshooting -FOR Professional Installer only LED Display After Code Problem Solution Pressing PMaintenance and Adjustments Maintenance RecordMaintenance Steps Date Performed By Comments Warranty Service Warranty InformationNeed Help or SERVICE? Opener Model Part Number Part Name

M-4700, M-4500 specifications

The Genie M-4500 and M-4700 are advanced aerial work platforms designed to enhance productivity and safety in various industrial and construction applications. Both models are well-known for their reliability and user-friendly features, making them popular choices for operators seeking efficient solutions for elevated work tasks.

The Genie M-4500 is a compact lift designed to elevate workers and materials up to 45 feet. One of its standout features is its impressive lifting capacity of up to 1,000 pounds, enabling it to safely handle heavy loads and multiple workers at once. The M-4500 is equipped with a unique four-wheel drive system, providing excellent traction on uneven surfaces, which is particularly beneficial for outdoor applications. The hydraulic scissor lift technology utilized in the M-4500 allows for stable and smooth vertical movements, minimizing the risk of accidents and enhancing overall safety.

On the other hand, the Genie M-4700 offers even greater lifting capabilities, reaching up to 47 feet with a comparable weight capacity of up to 1,000 pounds. With its extended platform size, the M-4700 is designed for bigger work areas, accommodating more tools and equipment. This model incorporates Genie’s advanced automatic leveling system, which ensures that the platform remains stable during operation, an essential feature when working on sloped or uneven terrain. The M-4700’s power options, including electric and diesel variants, provide operators with flexibility based on the specific site requirements.

Both models feature Genie’s patented Quick Positioning System, allowing for rapid setups and adjustments, further enhancing their operational efficiency. The control systems are intuitive, designed for ease of use, ensuring that operators can navigate the platforms effortlessly. Safety is also a primary concern, with integrated fall protection features, non-slip surfaces, and emergency descent systems.

In summary, the Genie M-4500 and M-4700 are top-tier aerial work platforms that combine lifting power, stability, and user-centric design to meet the demands of modern job sites. Their robust technology, combined with advanced safety features, ensures that users can complete tasks efficiently while minimizing risks. These models cater to various applications in construction, maintenance, and more, solidifying their position as essential tools in the aerial work equipment market.
Top Page Image Contents