Audi AUD-S owner manual Electrical Wiring Instructions

Page 10

10

ELECTRICAL WIRING INSTRUCTIONS

WARNING

WARNING

TO PREVENT THE RISK OF PERSONAL INJURY OR DEATH :

•DISCONNECT POWER AT THE FUSE BOX BEFORE PROCEEDING.

•ELECTRICAL CONNECTIONS MUST BE MADE BY A QUALIFIED INDIVIDUAL.

•OBSERVE LOCAL ELECTRICAL CODES WHEN WIRING THE OPERATOR.

WARNING: The AUD-S Series operators have been designed and constructed for use with voltages from 115 Volts AC to 480 Volts AC, in single or three phase. Check the operator nameplate label on the control box cover for the proper voltage and phase. The application of an improper input voltage or phase will result in catastrophic failure to the internal electrical components.

Observe local electrical codes when wiring the operator.

When hard wiring, observe state and local electrical codes. A wiring diagram is attached to the inside of the control box cover. Connect the appropriate voltage and phase power leads to the appropriate terminals as per the wiring diagram and connect a ground wire to the grounding screw. On three phase units, incorrect phasing of the power supply will cause the motor to rotate in the wrong direction (open when CLOSE button is pushed and vice versa). To correct this, interchange any two of the incoming three phase conductors.

The wiring diagram attached inside the cover of the control box details all of the field wiring terminal connections for the operator. Always connect the wires to the push-button controls and auxiliary devices exactly as shown.

Warning: Control voltage of the opener is 5 volts DC, Class 2. Do not run the power leads and control circuit wiring in the same electrical conduit.

RISK OF ENTRAPMENT THAT MAY

RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE OPENER BEFORE AND DURING INSTALLATION OF AN ACCESSORY REVERSING DOOR EDGE OR PHOTOELECTRIC DEVICE. DO NOT RECONNECT POWER TO OPENER UNTIL INSTRUCTED TO DO SO. ENSURE DOORWAY IS CLEAR BEFORE STARTING TESTING OF UNIT.

Note: AUD-S Series model openers are pre-wired for door reversing edge components. To comply with code requirements, the door reversing edge components must be installed and wired to the opener. Refer to Figure 15 Door Edge component installation and Figure 16 for Door Edge and photoelectric device wiring.

If a Safe-Finish™ or Access Alliance Safe-Finish II™ photo- beam is connected and the photo-beam detects an obstruction or becomes inactive, an opening door continues to open and a closing door stops, pauses and starts open. While in this mode, if a problem is detected while the opener is stopped, a close action will require constant activation of the push button. If the photo-beam is attached and is properly working for 1 second, it will be auto detected and the monitored function will be turned on. Once the monitoring function is active, it will remain active even if the power is removed and the photo-beam is disconnected and power is restored. While in this mode, if a problem is detected while the opener is stopped, a close will require constant activation.

Openers which are equipped with a reversing edge circuit may have one or more additional means of control which should be wired in accordance with the diagram supplied in the opener and also illustrated on Pages 20 & 21. To add a second three button station, refer to Figure 18.

WARNING

TO PREVENT THE RISK OF PERSONAL INJURY AND/OR DAMAGE TO DOOR OR PROPERTY, ONLY OPERATE DOOR CONTROL WHEN DOOR IS IN CLEAR VIEW. IF CONTROL STATION CANNOT BE LOCATED WHERE THE DOOR IS VISIBLE OR IF ANY OTHER DEVICE IS USED TO CONTROL THE DOOR AN AUXILIARY ENTRAPMENT DEVISE (DOOR EDGE OR PHOTOELECTRIC) MUST BE CONNECTED.

Number 22 gauge wire or heavier must be used for wiring the control stations and auxiliary control devices to the operator. Smaller gauge wire will cause operational problems, especially when multiple push-button stations are used or during summer months.

CAUTION

TO AVOID DAMAGE TO DOOR AND OPERATOR ENSURE ALL DOOR LOCKS ARE DISABLED.

USE AN INTERLOCK SWITCH IF A LOCK IS REQUIRED TO RETAIN FUNCTIONALITY.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents AUD-S Table of Contents Product Features Standard Features4PREPARATION Component Identification PictorialComponent Identification Listing Item # PART# Description QuanRAIL/CHAIN Assembly Instructions RAIL/CHAIN Assembly107096 107094 SPRINGS, PULLEYS, Cables and Mounting Hardware Used to Details a typical method of hanging the operator Electrical Wiring Instructions Pneumatic Door Edge Installation Field Wiring Door Edge and Photoelectric Wiring12 3/SINGLE Button Station / Interlock Field Wiring Turning on the Power to the OperatorDeath Read and Follow ALL Instructions Settable Switches Location Operation and Adjustment Instructions Setup ModesBrake Adjustment Mid-Stop Limit SetupLimit Assembly Operation and Adjustment Instructions Clutch Adjustment Operation and Adjustment Instructions Testing MaintenanceWiring DIAGRAM/SCHEMATIC Single Phase LoadWiring DIAGRAM/SCHEMATIC Three Phase LoadOperator Dimensions / Notes Operator DimensionsParts Identification DescriptionManufacturer’s Limited Warranty

AUD-S specifications

The Audi AUD-S is a striking representation of the brand's commitment to performance, luxury, and cutting-edge technology. Tailored for enthusiast drivers who crave a high-performance vehicle without sacrificing daily usability, the AUD-S harmonizes style and function in a captivating package.

One of the standout features of the AUD-S is its robust powertrain. Typically powered by a turbocharged V6 or V8 engine, the AUD-S is engineered to deliver exhilarating performance that pushes the boundaries of what drivers expect from a luxury sedan. With power output often exceeding 400 horsepower, the AUD-S can accelerate from 0 to 60 mph in a matter of seconds, offering a thrilling driving experience both on the track and the open road.

The AUD-S employs Audi's renowned quattro all-wheel-drive system, which enhances traction and stability in various driving conditions. This advanced system ensures that power is efficiently distributed to all four wheels, providing superior grip during acceleration and cornering, making the AUD-S a driver-focused vehicle that inspires confidence behind the wheel.

In terms of design, the AUD-S boasts an aggressive stance complemented by sleek lines and distinctive aerodynamic enhancements. Its bold front grille and sharp LED headlights not only contribute to its eye-catching appearance but also improve airflow and overall performance. The spacious interior is adorned with high-quality materials, including leather upholstery and aluminum or carbon fiber accents, providing an atmosphere of sophistication and luxury.

Technology in the AUD-S is state-of-the-art, featuring the latest version of Audi’s MMI infotainment system. The system provides intuitive controls for navigation, audio settings, and vehicle monitoring, ensuring that drivers stay connected while remaining focused on the road. A fully digital instrument cluster, known as the Virtual Cockpit, presents vital information in a crisp and customizable format.

Safety and driver assistance features are also a priority in the AUD-S. Equipped with various sensors and cutting-edge camera technology, the vehicle offers features such as adaptive cruise control, lane-keeping assist, and parking assistance, all designed to enhance safety and convenience behind the wheel.

In summary, the Audi AUD-S embodies the perfect blend of power, luxury, and technology. With its impressive performance capabilities, sophisticated design, and advanced features, the AUD-S stands out as a top contender in the high-performance luxury sedan market, offering an unparalleled driving experience for those who seek both excitement and elegance.
Top Page Image Contents