Audi AUD-S owner manual Settable Switches Location

14OPERATION AND ADJUSTMENT INSTRUCTIONS SETTING THE SWITCH SELECTABLE OPERATING MODES

Changing the Switch Selectable Operation Modes

The following modes are selected by setting the on-board dip switches, Figure 20 at right shows where the switches are located on the operator control board. For each Operational Mode, the switches are set to either ON or OFF according to the table at right below. For all the modes, if a reversing device is attached, it will function as noted. If a monitored reversing device has been recognized and becomes inactive then the mode will default to constant pressure activation for close regardless of the dip switch setting. The switches must be set to one of the six Operational Mode combinations for the operator to function.

C2 Operation (Factory default)

Open Button: Momentary activation; open override of closing door.

Close Button: Constant activation, door will stop when butto full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position;

Settable

Switches

Location

US		SW1
	S4
3 LD4	S3
	S2	OFF
	S1
	R27	R83
	R28	R61
		R60
		R5

Figure 20

P4

HIGH VOLTAGE

K6

K5

K3

K4

K2

P1

TR3

COM

CLS

OLS COM

STATUS

MO4

POWER

MO3

S4

MO2

P2

P3

LD2

S3

MO1

R89

R49

R10

R34 LD3

S2

ILK

TR1

R62

R22

R33

S1

OFF

24V

R47

C16

R23

R27

R83

R53

COM

R51

C6

R9

R61

R46

R48

R19

R20

R82

R60

R45

C13

TR2

R17

R18

D3

C3

R57

R13

R14

R65

R25

RADIO

R1

R21

C10

C24

C11

24V

D2

D8

C14

R52

RO1

COM

TR4

C9

R31

U1

RM3

EDGE

RM2

RM1

FRA

VCC

VCC

C30

P7

COM

S1

R85

C2

R38

R54

24V

R11

R12

R87

U4

R26

R29

R30

R55

P6

R58

C12

R15

R16

R94

C8

R56

Q1

R6

R7

R95

c.p. ALLSTAR CORP.

C7

R90

R84

R2

CDOMCB 2005

D1

R93

U5

R3

PCB 112695 REV B TSLK

R8

R4

C25

R24

C21

PB1

PB2

PB3

C1

D12

P5

OPEN

CLOSE

STOP

TB1

COM

24 VAC

ILOCK

SINGLE

COM

PHOTO

NC REV

NO REV

COM

STOP

CLOSE

OPEN

MOTOR CONTROL BOARD

if door is moving open, constant pressure on open button will bypass mid-stop.n is released.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door.

Reverse: Momentary activation will reverse a closing door, reverse to

Auto Close Timer: N/A.

B2 Operation

Open Button: Momentary activation; open override of closing door.

Close Button: Momentary activation.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door, closes door from mid-stop or open limit. Reverse: Momentary activation will reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: N/A.

D1 Operation

Open Button: Constant activation; open override of closing door.

Close Button: Constant activation, door will stop when button is released.

Stop Button: Momentary activation; stops open, close or reverse action (not required).

Single Button: N/A.

Reverse: Momentary activation will stop a closing door.

Operating	Switch	Switch	Switch	Switch
Mode	1	2	3	4
C2 Operation	OFF	OFF	OFF	OFF
B2 Operation	ON	OFF	OFF	OFF
D1 Operation	OFF	ON	OFF	OFF
E2 Operation	ON	ON	OFF	OFF
TS Operation	OFF	OFF	ON	OFF
T Operation	ON	OFF	ON	OFF

Mid-Stop: Activation stops an opening door; after the door stops at the mid stop, constant contact of open button at mid stop will restart door to full open position.

Auto Close Timer: N/A.

E2 Operation (roll-back)

Open Button: Momentary activation; open override of closing door.

Close Button: Constant activation, door will reverse to full open (ignores mid-stop) when button is released.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: N/A.

Reverse: Momentary activation to reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: N/A