Audi AUD-S owner manual Operation and Adjustment Instructions, Setup Modes

OPERATION AND ADJUSTMENT INSTRUCTIONS 15

TS Operation

Open Button: Momentary activation; open override of closing door.

Close Button: Momentary activation.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door, closes door from mid-stop or open limit. Reverse: Momentary activation will reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: Closes door from mid-stop or open limit after pre-set time. Stop will deactivate the auto close timer. Open will reactivate the auto close timer or reset the auto close timer when the door is at the mid-stop or open limit. Single button will reset the auto close timer from the mid-stop or open limit. Reverse will reactivate the auto close timer or reset the auto close timer when the door is at the mid-stop or open limit.

T Operation, Dip-Switch Setting

Open Button: Momentary activation; open override of closing door.

Close Button: Momentary activation.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door, closes door from mid-stop or open limit. Reverse: Momentary activation will reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: Closes door from mid-stop or open limit after pre-set time. Stop will deactivate the auto close timer. Open will reactivate the auto close timer or reset the auto close timer when the door is at the open limit. Single button will reset the auto close timer from the mid-stop or open limit. Reverse deactivates the auto close timer if the door is closing. Reverse will reset the auto close timer at the mid-stop or open limit if the auto close timer has not been previously deactivated.

SETUP MODES

Setup Modes	Setup Mode	Switch	Switch	Switch	Switch
Various operating characteristics can be modified via the setup		1	2	3	4
modes. The operator is moved to the close limit position and
	Delay on Reverse	ON	ON	ON	ON
the on-board dip switches (see Figure 20, page 14) are
TEMPORARILY set according to the table at right to enter a
	Close Limit Delay	OFF	ON	ON	ON
Setup Mode. The on board OPEN and STOP buttons are used
to modify the characteristic. Once set, the values are stored in	Mid-Stop Limit	ON	OFF	ON	ON
non-volatile memory.
	Auto Close Timer	OFF	OFF	ON	ON
These values are set to factory defaults that should be
satisfactory for many applications. All values as described here
	Maximum Run	OFF	ON	OFF	ON
can be reset to the factory defaults as follows:
	Time
Remove 24 VAC power from the control board.
Press and hold the on-board stop button.
Re-apply 24 VAC while holding the on-board stop button.	Operating Mode setting (see section previous).
After completing the procedure to modify the operating
characteristic the switches must be returned to the originally set	Close Limit Delay Setup
Operating Mode setting (see section previous).	To provide for irregularities in the floor, this feature allows for
Delay on Reverse Setup	the door to continue to travel down after the Reverse Cutout
	Limit is activated. The factory default time is 0.32 seconds; the
To help prevent stress on the door components, this feature	minimum time is 0.12 seconds; the maximum time is 0.66
allows for a delay time between the door stopping and reversing	seconds.
when a command to reverse is received as the door is closing.	After moving the door to the close position and temporarily
The factory default time is 0.75 seconds; the minimum time is	setting the switches to the appropriate settings in the table,
0.4 seconds; the maximum time is 2 seconds.	pressing STOP will reset the time to the minimum setting.
After moving the door to the close position and temporarily	Every time OPEN is pressed, 0.02 seconds are added to the time
setting the switches to the appropriate settings in the table,	(up to the maximum).
pressing STOP will reset the time to the minimum setting.	Changing the dip-switch setting to any other setting will save
Every time OPEN is pressed, 200 mS is added to the time (up to	the new time. Return the dip switches to the originally set
the maximum).	Operating Mode setting (see section previous).
Changing the dip-switch setting to any other setting will save
the new time. Return the dip switches to the originally set