Harman-Kardon DPR 1005 Additional Input Adjustments, To return to normal operation of the DPR

Page 29

SYSTEM CONFIGURATION

3.Press the Set Button q within five seconds to activate the remote’s manual mode, so that it func- tions as an SPL meter. The right corner of the bot- tom line of the remote’s display will show the output level of the speakers as the test tone circulates. The level will show as a direct SPL indication between 66dB and 79dB. Below 66dB the remote will read LOW and above 79dB it will read HIGH.

4.When you are finished with all adjustments, press the Clear Button 9 to return the remote to nor- mal operation.

NOTE: The subwoofer level is not adjustable when the normal test tone is in use. The subwoofer output level may also be adjusted when the channel levels are being trimmed to a program source rather than the test tone, as shown on page 36.

When all channels have an equal volume level, the adjustment is complete. To exit this menu, press the ⁄/¤ Navigation Button o until the on-screen

➔cursor is next to the BACK TO MASTER MENU line, and then press the Set Button q to return to the MASTER MENU.

To adjust the output levels at any time using the remote control and semi-OSD messages, first press the Test Button f. As soon as the button is pressed, the test tone will begin to circulate as indicated earlier. The correct channel from which the test noise should be heard will be shown on the video screen and the Lower Display Line &. While the test noise is circulating, the proper channel position will also be indicated in the Speaker/ Channel Input Indicators % by a blinking letter within the correct channel.

To adjust the output level, press the ⁄/¤ Navigation Button o until the desired level is heard. Once the buttons are released, the test noise will begin to circulate again in five seconds.

When all channels have the same output level, press the Test Button f again to complete the process.

NOTE: Output level adjustment is not available for the VMAx or Surround Off modes.

Additional Input Adjustments

After one input has been adjusted for Surround mode, digital input (if any), speaker type, and output levels, go back to the IN/OUT SETUP line on the MASTER MENU (Figure 1) and enter the set- tings for each input you will use. In most cases, only the digital input and surround mode will be different from one input to the next, while the other settings will usually be the same.

If you wish to have different speaker “size” and crossover settings for an input, remember to change the BASS MGR setting to INDEPENDENT, as shown on page 26. When all settings and adjust- ments have been made, press the OSD Button

to return to normal operation of the DPR.

Once the settings outlined on the previous pages have been made, the DPR 1005 is ready for operation. While there are some additional settings to be made, these are best done after you have had an opportunity to listen to a variety of sources and different kinds of program material. These advanced settings are described on pages 37 and 38 of this manual. In addition, any of the settings made in the initial configu- ration of the unit may be changed at any time. As you add new or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown in this section.

Having completed the setup and configuration process for your DPR 1005, you are about to experience the finest in music and home theater listening. Enjoy!

SYSTEM CONFIGURATION 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Digital Path Receiver DPRSee trademark acknowledgements on DPR 1005 Digital Path ReceiverIntroduction Description and FeaturesThank You for Choosing Harman Kardon Modèle pour les CanadienImportant Safety Information Safety InformationSurround Mode Indicators To choose from the various mode optionsStandby/On Indicator This indicator is amber Modes, and then press the Surround Mode SelectorFRONT-PANEL Controls AB C D E F G H J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections Volume Up/Down Buttons Main Remote Control FunctionsProgram Button SPL Select Button EzSet Microphone Sensor LensHave been pressed Channel Up/Down Selector . To raiseSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions System Installation Installation and ConnectionsSystem and Power Connections RS-232 Connections BUSInstallation ConnectionsAC Power Connections Speaker Placement System ConfigurationSystem Setup Speaker Selection and PlacementMaking Configuration Adjustments Input SetupSetting the System Configuration Memory For DVD and the Optical Digital Input 1 ‡Cursor is next to the REC OUT line, press › Navigation Button oSurround Setup Audio SetupFor added resolution Speaker OptimizerTo return to the Master Menu DTS-ES Discrete. Press the ‹/› Navigation Button Speaker SetupSet the unit for either 5.1 or 6.1/7.1 operation Measurement units is made, press the ⁄/¤ Delay SettingsTo bring up the Master Menu and press Using EzSet Output Level AdjustmentNavigation Button o to return the cursor to the FL position To change one of the individual speaker positionsUsing the EzSet remote Manual Output Level AdjustmentMENU, press the OSD Button to bring up Play shown in FigureTo return to normal operation of the DPR Additional Input AdjustmentsOperation Volume and Tone ControlBasic Operation Source SelectionDolby Mode Select Button or Surround Mode SelectionDigital Audio Playback Digital DTS Neo6Surround Mode Chart Hdcd Playback Selecting a Digital SourcePCM Playback MP3 Audio Playback Speaker/Channel IndicatorsNight Mode Front-Panel Connections Tuner OperationTape Recording Memory Backup Output Level Trim AdjustmentMenu system Dim Function Ments to make, press the OSD ButtonMenu system Turn-On Volume Level Advanced FeaturesMenu system Semi-OSD Settings Button is pressed is shownMenu system Installation Multiroom SetupMultiroom Operation RS-232 ControlButtons ç∂d Multiroom OperationSpecific source OutputRemote’s Main Menu message Configuring the RemoteProgramming Remote Codes Bottom line Learning CommandsBe used Input Selector Button d that was justChanging Devices Commands from another device’s remote into the DPR remoteRemember that when you want to change devices Macro. The choices are the Power On ButtonMacro Programming Lower line of the display and then press the Set Button qProgrammed e.g., the Power On Button 1 or Power On VID 2/TV VID 3/Cable DPR Logic 7 hErasing a Macro Read a MacroChannel Punch-Through Punch-Through ConfigurationVolume Punch-Through When the red light under the Set Button q appears EzSet ConfigurationPages 27 RenamingRenaming a Device Numeric KeysAt this point you have two options Resetting the RemoteRenaming Individual Keys Additional Notes on Configuring and Operating the Remote Processor Reset Troubleshooting GuideDPR 1005 Technical Specifications

DPR 1005 specifications

The Harman-Kardon DPR 1005 is a remarkable piece of audio technology that has gained a loyal following among home theater enthusiasts. Launched as part of Harman-Kardon's digital receiver line, it combines sophisticated features with outstanding sound quality, making it an ideal choice for both music lovers and cinephiles.

One of the standout characteristics of the DPR 1005 is its powerful 7.1-channel amplifier, delivering an impressive 75 watts per channel. This configuration enables robust sound for both stereo and surround sound applications, ensuring that users can enjoy their favorite media with rich detail and clarity. The receiver is capable of decoding a variety of surround sound formats, including Dolby Digital, DTS, and more, allowing for an immersive auditory experience that enhances movie nights and music sessions alike.

The DPR 1005 integrates advanced digital processing technologies, including Harman-Kardon’s proprietary Logic 7 processing. This technology is crucial for creating a wide soundstage and providing a genuine multichannel experience from stereo sources. Furthermore, the receiver features a built-in AM/FM tuner, allowing users to easily access their favorite radio stations.

Connectivity is another strong suit of the DPR 1005. It comes equipped with multiple inputs and outputs, including HDMI ports, composite video, and S-Video connections, which facilitate seamless connection to a variety of devices such as Blu-ray players, gaming consoles, and set-top boxes. Additionally, it features an audio return channel via HDMI, which simplifies the connection to televisions, enabling an easy setup for both audio and video.

For those who appreciate fine-tuning their audio experience, the DPR 1005 offers an array of customizable sound settings. The receiver provides various equalization options and allows users to tailor the audio output to suit their preference and room acoustics. The on-screen menu is user-friendly, making adjustments straightforward even for those who may not be tech-savvy.

A noteworthy design element of the DPR 1005 is its sleek and modern aesthetic, fitting effortlessly within any home entertainment center. The display is clear and informative, ensuring easy navigation and control.

In summary, the Harman-Kardon DPR 1005 is a versatile and high-performance digital receiver that combines cutting-edge technologies with excellent sound quality. With its powerful amplification, advanced processing capabilities, and connectivity options, it stands as a formidable choice for those seeking an enhanced audio and visual experience. Its design and user-friendly features further solidify its position as a valuable addition to any home entertainment system.
Top Page Image Contents