Harman-Kardon DPR 1005 Multiroom Operation, Multiroom Setup, Installation, RS-232 Control

Page 39

MULTIROOM OPERATION

The DPR 1005 is fully equipped to operate as the control center for a complete multiroom system that is capable of sending one source to a second zone in the house while a separate source is listened to in the main room. In addition to providing for control over the selection of the remote source and its volume, the DPR 1005 offers a comprehensive range of options for powering the speakers in the second zone.

■Using the line-level Multiroom Audio Outputs ª, the selected source may be fed to optional, external power amplifiers that may be matched to the specifics of the installation.

■When the main room system is configured for 5.1 operation, the Surround Back Left/Right amplifier channels may be used to power the remote zone so that no additional amplifiers are required.

■Using built-in A-BUS Ready technology, optional A-BUS modules may be connected to the DPR 1005 via a single Category 5/5e or higher wire, so that remote zone speakers may be pow- ered directly from the A-BUS module without the need for additional power, IR sensor or volume con- trol wires to be run to the second zone.

In addition, the DPR 1005 includes a remote IR sen- sor input so that remote control commands from the Zone II remote included with the unit may be transmitted to the unit, while standard IR input/output jacks allow the remote zone’s commands to be sent to compatible IR-controlled source devices.

Installation

For installations where A-BUS modules are used, fol- low the instructions provided with the A-BUS remote modules or keypads.

RS-232 Control

The DPR 1005 is rare among A/V receivers in that it provides the capability for full bidirectional remote con- trol with confirmation control acknowledgement from compatible computers or specialized remote control systems. RS-232 programming requires specialized programming knowledge and for that reason we rec- ommend that it only be done by qualified installers. For more information on using the RS-232 port for remote control, visit the Harman Kardon Web site at www.harmankardon.com or contact a custom installer trained in RS-232 controlled systems.

Multiroom Setup

Once the audio and IR link connections have been made, the DPR 1005 needs to be configured for multi-

room operation. Press the OSD Button to bring the MASTER MENU (Figure 1) to the screen. Press the ¤ Navigation Button o, until the on- screen ➔ cursor is next to the MULTI-ROOM line. Press the Set Button q to enter the MULTI-ROOM SETUP menu (Figure 17).

 

* M U L T I - R O O M S E T U P *

→

 

 

 

 

 

M U L T I - R O O M :

O F F

O N

 

 

 

 

 

 

 

 

M U L T I I N

:

F M P R E S E T 0 1

 

M U L T I V O L

:

 

 

 

 

 

 

 

S B A M P S

:

M A I N

M U L T I

B A C K T O M A S T E R M E N U

input must be analog. When MAIN DOWNMIX is selected as the multiroom system input you may lis- ten to an “Lt/Rt” stereo version of any digital source playing in the main room, such as Dolby Digital or DTS. You may also use this mode to listen to a source connected to the 8-Channel Direct Inputs fi in the remote zone, as long as the Dolby Pro Logic IIx mode is activated. Note, however, that when MAIN DOWNMIX is selected as the input for the multi- room system, the source sent to the remote room will change any time the main room input is changed.

When the selection has been made, press the ¤ Navigation Button o once so that the ➔ on- screen cursor is next to the MULTI VOL line.

At the MULTI VOL line, press the ‹/› Navigation Button o until the desired volume level for the multiroom system is entered. DO NOT use the regular volume control knobs for this setting. When all settings for the multiroom setup have been made, press the ⁄/¤ Navigation Button o until the on-screen ➔ cursor is next to the BACK TO MASTER MENU line.

However, if you have connected both the digital and analog outputs of a source such as a DVD player to the DPR, you may select that source for the remote room. The DPR will automatically switch to the analog connection for playback in the remote room without affecting multichannel playback from the digital link in the main room.

Although simple remote room systems may be installed by the average do-it-yourself hobbyist,

the complexity of many multizone/multiroom systems involves running wires inside walls where the services of a specially trained installer may be required. Regard- less of who does the work, please remember that local building codes govern in-wall electrical work, including proper specification of any wiring used and the way in which it is connected. You are responsible for making certain that all multiroom installation work is done properly and in compliance with all applicable codes and regulations.

For installations using optional, external amplifiers in Option 1 or Option 2, follow the instructions shown on page 17.

For installations where the Surround Back Left/Right amplifier channels are used to power the remote zone, make certain that the system is installed and configured for that type of operation, as shown. In Option 3 on page 17 and in the MULTI-ROOM SETUP menu as shown on this page.

Figure 17

When the MULTI-ROOM SETUP menu appears, the on-screen ➔ cursor will be at the MULTI-ROOM line. Since this line is used to turn the system on and off, don’t make an adjustment here unless you wish to turn the system on at this time. To turn the system on, press the › Navigation Button

oso that ON is highlighted. If you do not wish to turn the system on at this time or to proceed to the next step, press the ¤ Navigation Button o once so that the ➔ on-screen cursor is next to the MULTI IN line.

At the MULTI IN line, press the ‹/› Navigation Button o until the desired input to the multiroom system appears in the highlighted video.

In addition to the standard inputs, a choice is available labeled MAIN DOWNMIX. In all other cases, the feed to the multiroom system may be different from the input selected for the main room, but the

Surround Amplifier Channel Assignment

The DPR 1005 is equipped with seven full-power amplifier channels to allow for complete 7.1-channel operation without the need for additional external amplifiers. However, in some installations you may wish to use the traditional 5.1-channel configuration for the main listening room, which allows the surround back left/right amplifier channels to be used to power speakers placed in a remote zone location.

If you wish to use the Surround Back amplifier chan- nels to power the remote zone, press the ⁄/¤ Navigation Button o until the ➔ cursor is pointing to the SB AMPS line on the MULTI-ROOM SETUP menu. Press the ‹/› Navigation Button

ountil MULTI is highlighted in reverse video and press the Set Button q.

Remember that once this setting is made, you will not be able to take advantage of any of the 6.1/7.1- channel decoding or processing modes, and that the speakers used for the remote zone must be connected to the Surround Back/Multiroom Speaker Outputs g. The volume for these speakers is set by the multiroom system, as explained on this page.

MULTIROOM OPERATION 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Digital Path Receiver DPRSee trademark acknowledgements on DPR 1005 Digital Path ReceiverModèle pour les Canadien Description and FeaturesIntroduction Thank You for Choosing Harman KardonImportant Safety Information Safety InformationModes, and then press the Surround Mode Selector To choose from the various mode optionsSurround Mode Indicators Standby/On Indicator This indicator is amberFRONT-PANEL Controls AB C D E F G H J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections SPL Select Button EzSet Microphone Sensor Lens Main Remote Control FunctionsVolume Up/Down Buttons Program ButtonHave been pressed Channel Up/Down Selector . To raiseSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions System Installation Installation and ConnectionsSystem and Power Connections BUSInstallation Connections AC Power ConnectionsRS-232 Connections Speaker Selection and Placement System ConfigurationSpeaker Placement System SetupFor DVD and the Optical Digital Input 1 ‡ Input SetupMaking Configuration Adjustments Setting the System Configuration MemoryCursor is next to the REC OUT line, press › Navigation Button oSpeaker Optimizer Audio SetupSurround Setup For added resolutionTo return to the Master Menu DTS-ES Discrete. Press the ‹/› Navigation Button Speaker SetupSet the unit for either 5.1 or 6.1/7.1 operation Delay Settings To bring up the Master Menu and pressMeasurement units is made, press the ⁄/¤ To change one of the individual speaker positions Output Level AdjustmentUsing EzSet Navigation Button o to return the cursor to the FL positionPlay shown in Figure Manual Output Level AdjustmentUsing the EzSet remote MENU, press the OSD Button to bring upTo return to normal operation of the DPR Additional Input AdjustmentsSource Selection Volume and Tone ControlOperation Basic OperationDigital DTS Neo6 Surround Mode SelectionDolby Mode Select Button or Digital Audio PlaybackSurround Mode Chart Selecting a Digital Source PCM PlaybackHdcd Playback Speaker/Channel Indicators Night ModeMP3 Audio Playback Tuner Operation Tape RecordingFront-Panel Connections Ments to make, press the OSD Button Output Level Trim AdjustmentMemory Backup Menu system Dim FunctionButton is pressed is shown Advanced FeaturesMenu system Turn-On Volume Level Menu system Semi-OSD SettingsMenu system RS-232 Control Multiroom SetupInstallation Multiroom OperationOutput Multiroom OperationButtons ç∂d Specific sourceConfiguring the Remote Programming Remote CodesRemote’s Main Menu message Input Selector Button d that was just Learning CommandsBottom line Be usedChanging Devices Commands from another device’s remote into the DPR remoteLower line of the display and then press the Set Button q Macro. The choices are the Power On ButtonRemember that when you want to change devices Macro ProgrammingRead a Macro Power On VID 2/TV VID 3/Cable DPR Logic 7 hProgrammed e.g., the Power On Button 1 or Erasing a MacroPunch-Through Configuration Volume Punch-ThroughChannel Punch-Through When the red light under the Set Button q appears EzSet ConfigurationNumeric Keys RenamingPages 27 Renaming a DeviceResetting the Remote Renaming Individual KeysAt this point you have two options Additional Notes on Configuring and Operating the Remote Processor Reset Troubleshooting GuideDPR 1005 Technical Specifications

DPR 1005 specifications

The Harman-Kardon DPR 1005 is a remarkable piece of audio technology that has gained a loyal following among home theater enthusiasts. Launched as part of Harman-Kardon's digital receiver line, it combines sophisticated features with outstanding sound quality, making it an ideal choice for both music lovers and cinephiles.

One of the standout characteristics of the DPR 1005 is its powerful 7.1-channel amplifier, delivering an impressive 75 watts per channel. This configuration enables robust sound for both stereo and surround sound applications, ensuring that users can enjoy their favorite media with rich detail and clarity. The receiver is capable of decoding a variety of surround sound formats, including Dolby Digital, DTS, and more, allowing for an immersive auditory experience that enhances movie nights and music sessions alike.

The DPR 1005 integrates advanced digital processing technologies, including Harman-Kardon’s proprietary Logic 7 processing. This technology is crucial for creating a wide soundstage and providing a genuine multichannel experience from stereo sources. Furthermore, the receiver features a built-in AM/FM tuner, allowing users to easily access their favorite radio stations.

Connectivity is another strong suit of the DPR 1005. It comes equipped with multiple inputs and outputs, including HDMI ports, composite video, and S-Video connections, which facilitate seamless connection to a variety of devices such as Blu-ray players, gaming consoles, and set-top boxes. Additionally, it features an audio return channel via HDMI, which simplifies the connection to televisions, enabling an easy setup for both audio and video.

For those who appreciate fine-tuning their audio experience, the DPR 1005 offers an array of customizable sound settings. The receiver provides various equalization options and allows users to tailor the audio output to suit their preference and room acoustics. The on-screen menu is user-friendly, making adjustments straightforward even for those who may not be tech-savvy.

A noteworthy design element of the DPR 1005 is its sleek and modern aesthetic, fitting effortlessly within any home entertainment center. The display is clear and informative, ensuring easy navigation and control.

In summary, the Harman-Kardon DPR 1005 is a versatile and high-performance digital receiver that combines cutting-edge technologies with excellent sound quality. With its powerful amplification, advanced processing capabilities, and connectivity options, it stands as a formidable choice for those seeking an enhanced audio and visual experience. Its design and user-friendly features further solidify its position as a valuable addition to any home entertainment system.
Top Page Image Contents