Harman-Kardon DPR 1005 owner manual FRONT-PANEL Controls

Page 6

FRONT-PANEL CONTROLS

to select a category such as Dolby or Logic 7, and then press this button to see the specific mode choices that are available. For more information on mode selection, see page 32.

5Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When the tuner is in the MANUAL/MONO mode, each tap of the Selector will increase or decrease the frequency by one increment. When the tuner receives a strong-enough signal for adequate reception, MANUAL TUNED will appear in the Lower Display Line & and in the on-screen display. When the tuner is in the AUTO/STEREO mode, press the button once, and the tuner will scan for a station with acceptable signal strength. When the next higher or lower frequency station with a strong-enough signal is tuned, the frequency scan will stop and the Lower Display Line & and the on-screen display will indicate AUTO TUNED. When an FM Stereo station is tuned, the display will read AUTO ST TUNED. See page 35 for more information on using the tuner.

6Tuner Band Selector: Pressing this button will automatically switch the DPR 1005 to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands. (See page 35 for more information on the tuner.)

7Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 35 for more information on tuner programming.)

8Input Source Selector: Press this button to change the input by scrolling up or down through the list of input sources.

9Tuning Mode Selector: Press this button to select Auto or Manual tuning. When the button is pressed so that AUTO/STEREO appears in the Upper Display Line ^, the tuner will search for the next sta- tion with an acceptable signal when the Tuning Selector 5wé is pressed. When the button is pressed so that MANUAL/MONO appears in the Upper Display Line ^, each press of the Tuning Selector 5wé will increase the frequency. (See page 35 for more information on using the tuner.) This button may also be used to switch between Stereo and Mono modes for FM radio reception. When weak reception is encountered, select the Manual/Mono tuning mode. Press and hold again to switch back to Stereo mode. (See page 35 for more information on using the tuner.)

)Set Button: When making system configuration changes using the front-panel controls, press this but- ton to enter a setting into the unit’s memory.

!¤/⁄ Buttons: When making system configura- tion changes using the front-panel controls, press these buttons to scroll through the available choices for the option being adjusted.

@Front-Panel Control Door: To open the door so that the front-panel jacks and controls behind this door may be accessed, press the center of the door and gently swing it down towards you.

#Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the DPR 1005 is muted, adjusting the vol- ume control will automatically release the unit from the silenced condition.

$Input Indicators: One of these indicators will light to identify the currently selected input. Note that the entire list will light briefly each time the unit is turned on as a test.

%Speaker/Channel Input Indicators: These indi- cators are multipurpose, indicating both the speaker type selected for each channel and the incoming data- signal configuration. The left, center, right, right surround and left surround speaker indicators light as a single outline around the speaker position indicator when a “small” speaker is selected and as a larger icon with three connected boxes when “large” speakers are selected. When only the speaker position letters appear, no speaker has been assigned that position. (See page 24 for more information on configuring speakers.) The letters inside each box also indicate the active input channels. For standard analog inputs, only the L and R will light, indicating a stereo input. For a digital source, the indicators will light to display the channels being received at the digital input. When the letters flash, the digital input has been interrupted and an UNLOCK message may appear in the Lower Display Line &. (See page 34 for more information on the Channel Indicators.)

^Upper Display Line: Depending on the unit’s status, a variety of messages will appear here. In normal operation, this line will show the current input source and identify whether an analog or digital input is in use. When the tuner is selected as the input, this line will identify the station as AM or FM and show the frequency and preset number, if any.

&Lower Display Line: Depending on the unit’s status, a variety of messages will appear here. In nor- mal operation, the current surround mode will appear on this line.

*Surround Mode Indicators: One of these indicators will light to show the surround mode in use. Depending on the specific combination of input sources and surround mode selected, more than one indicator may light. (See page 33 for more information.)

(Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.

6 FRONT-PANEL CONTROLS

Page 5 Page 7
Image 6
Page 5 Page 7
Contents DPR Digital Path ReceiverDPR 1005 Digital Path Receiver See trademark acknowledgements onThank You for Choosing Harman Kardon Description and FeaturesIntroduction Modèle pour les CanadienSafety Information Important Safety InformationStandby/On Indicator This indicator is amber To choose from the various mode optionsSurround Mode Indicators Modes, and then press the Surround Mode SelectorFRONT-PANEL Controls AB C D E F G H J I K REAR-PANEL Connections ‚ CD Audio Inputs Connect these jacks to REAR-PANEL Connections Program Button Main Remote Control FunctionsVolume Up/Down Buttons SPL Select Button EzSet Microphone Sensor LensChannel Up/Down Selector . To raise Have been pressedSpeaker Select Button Press this button Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System InstallationSystem and Power Connections BUSInstallation Connections AC Power ConnectionsRS-232 Connections System Setup System ConfigurationSpeaker Placement Speaker Selection and PlacementSetting the System Configuration Memory Input SetupMaking Configuration Adjustments For DVD and the Optical Digital Input 1 ‡› Navigation Button o Cursor is next to the REC OUT line, pressFor added resolution Audio SetupSurround Setup Speaker OptimizerTo return to the Master Menu Speaker Setup DTS-ES Discrete. Press the ‹/› Navigation ButtonSet the unit for either 5.1 or 6.1/7.1 operation Delay Settings To bring up the Master Menu and pressMeasurement units is made, press the ⁄/¤ Navigation Button o to return the cursor to the FL position Output Level AdjustmentUsing EzSet To change one of the individual speaker positionsMENU, press the OSD Button to bring up Manual Output Level AdjustmentUsing the EzSet remote Play shown in FigureAdditional Input Adjustments To return to normal operation of the DPRBasic Operation Volume and Tone ControlOperation Source SelectionDigital Audio Playback Surround Mode SelectionDolby Mode Select Button or Digital DTS Neo6Surround Mode Chart Selecting a Digital Source PCM PlaybackHdcd Playback Speaker/Channel Indicators Night ModeMP3 Audio Playback Tuner Operation Tape RecordingFront-Panel Connections Menu system Dim Function Output Level Trim AdjustmentMemory Backup Ments to make, press the OSD ButtonMenu system Semi-OSD Settings Advanced FeaturesMenu system Turn-On Volume Level Button is pressed is shownMenu system Multiroom Operation Multiroom SetupInstallation RS-232 ControlSpecific source Multiroom OperationButtons ç∂d OutputConfiguring the Remote Programming Remote CodesRemote’s Main Menu message Be used Learning CommandsBottom line Input Selector Button d that was justCommands from another device’s remote into the DPR remote Changing DevicesMacro Programming Macro. The choices are the Power On ButtonRemember that when you want to change devices Lower line of the display and then press the Set Button qErasing a Macro Power On VID 2/TV VID 3/Cable DPR Logic 7 hProgrammed e.g., the Power On Button 1 or Read a MacroPunch-Through Configuration Volume Punch-ThroughChannel Punch-Through EzSet Configuration When the red light under the Set Button q appearsRenaming a Device RenamingPages 27 Numeric KeysResetting the Remote Renaming Individual KeysAt this point you have two options Additional Notes on Configuring and Operating the Remote Troubleshooting Guide Processor ResetDPR 1005 Technical Specifications

DPR 1005 specifications

The Harman-Kardon DPR 1005 is a remarkable piece of audio technology that has gained a loyal following among home theater enthusiasts. Launched as part of Harman-Kardon's digital receiver line, it combines sophisticated features with outstanding sound quality, making it an ideal choice for both music lovers and cinephiles.

One of the standout characteristics of the DPR 1005 is its powerful 7.1-channel amplifier, delivering an impressive 75 watts per channel. This configuration enables robust sound for both stereo and surround sound applications, ensuring that users can enjoy their favorite media with rich detail and clarity. The receiver is capable of decoding a variety of surround sound formats, including Dolby Digital, DTS, and more, allowing for an immersive auditory experience that enhances movie nights and music sessions alike.

The DPR 1005 integrates advanced digital processing technologies, including Harman-Kardon’s proprietary Logic 7 processing. This technology is crucial for creating a wide soundstage and providing a genuine multichannel experience from stereo sources. Furthermore, the receiver features a built-in AM/FM tuner, allowing users to easily access their favorite radio stations.

Connectivity is another strong suit of the DPR 1005. It comes equipped with multiple inputs and outputs, including HDMI ports, composite video, and S-Video connections, which facilitate seamless connection to a variety of devices such as Blu-ray players, gaming consoles, and set-top boxes. Additionally, it features an audio return channel via HDMI, which simplifies the connection to televisions, enabling an easy setup for both audio and video.

For those who appreciate fine-tuning their audio experience, the DPR 1005 offers an array of customizable sound settings. The receiver provides various equalization options and allows users to tailor the audio output to suit their preference and room acoustics. The on-screen menu is user-friendly, making adjustments straightforward even for those who may not be tech-savvy.

A noteworthy design element of the DPR 1005 is its sleek and modern aesthetic, fitting effortlessly within any home entertainment center. The display is clear and informative, ensuring easy navigation and control.

In summary, the Harman-Kardon DPR 1005 is a versatile and high-performance digital receiver that combines cutting-edge technologies with excellent sound quality. With its powerful amplification, advanced processing capabilities, and connectivity options, it stands as a formidable choice for those seeking an enhanced audio and visual experience. Its design and user-friendly features further solidify its position as a valuable addition to any home entertainment system.
Top Page Image Contents