Harman-Kardon AVR 520 System Setup, Plug the AC Power Cord · into an unswitched AC outlet

Page 19

System Configuration

System Setup

Once the speakers have been placed in the room and connected, the remaining steps in the setup process are to program the AVR 520’s bass management system for the type of speakers used in your system, calibrate the output levels, and set the delay times used by the surround-sound processor.

You are now ready to power up the AVR 520 to begin these final adjustments.

1.Plug the AC Power Cord · into an unswitched AC outlet.

2.Press the Main Power Switch 1 in until it latches and the word “OFF” on the top of the switch disappears inside the front panel. Note that the Power Indicator 3 will turn amber, indicating that the unit is in the Standby mode.

3.Remove the protective plastic film from the front-panel lens. If left in place, the film may affect the performance of your remote control.

4.Install the three supplied AAA batteries in the remote as shown. Be certain to follow the (+) and (–) polarity indicators that are on the top of the battery compartment.

5.Turn the AVR 520 on either by pressing the System Power Control 2 on the front panel, or via the remote by pressing the Power On Button d, the AVR Selector for any of the Input Selectors egon the remote. The Power Indicator 3 will turn green to confirm that the unit is on, and the Main Information Display ˜ will also light.

Using the On-Screen Display

When making the following adjustments, you may find it easier to use the AVR 520’s on- screen display system. These easy-to-read dis- plays give you a clear picture of the current status of the unit and make it easy to see which speaker, delay, input or digital selection you are making.

To view the on-screen menus, make certain you have made a connection from the Video Monitor Out Jack ¤ on the rear panel to the composite or S-Video input of your TV or projector. In order to view the AVR 520’s dis- plays, the correct video source must be selected

on the video display. Note that the on-screen menus are not available when a component video display is in use.

IMPORTANT NOTE: When viewing the on- screen menus using a CRT-based projector, plasma display or any direct-view CRT monitor or television, it is important that they not be left on the screen for an extended period of time. The constant display of a static image such as these menus or video game images may cause the image to be permanently “burned into” the pro- jection tubes, plasma screen or CRT. This type of damage is not covered by the AVR 520 warranty and may not be covered by the projector/TV set’s warranty.

The AVR 520 has two on-screen display modes, “Semi-OSD” and “Full-OSD.” When making configuration adjustments, it is recommended that the Full-OSD mode be used. This will place an option listing on the screen, making it easier to view the available options.

Making Configuration Adjustments

The full-OSD system is available by pressing the OSD Button v. When this button is pressed, the MASTER menu (Figure 1) will appear, and adjustments are made from the individual menus.

* M A S T E R M E N U *

I N / O U T S E T U P

S U R R O U N D S E T U P

S P E A K E R S E T U P

D E L A Y A D J U S T

C H A N N E L A D J U S T

M U L T I - R O O M

A D V A N C E D

E X I T

Figure 1

The semi-OSD system is also available, allowing you to make adjustments directly, by pressing the appropriate buttons on the front panel or remote control for the specific parameter to be adjusted. For example, to change the digital input for any of the sources, press the Digital Select Button Ûq on the front panel or remote.

To use the full OSD menu system, press the OSD Button v. When the menu is on the screen, press the /¤ Buttons n until the on-screen cursor is next to the item you wish to adjust, and then press the Set Button p to adjust that item. Note that the menus will remain on the screen for 20 seconds, and then they will “time-out” and disappear from the screen. The time-out may be increased to as much as 50 seconds by going to the

ADVANCED SELECT menu, and changing the item titled FULL OSD TIME OUT.

Note that when the full OSD system is in use, the menu selections are not shown in the Main Information Display ˜Y. When the full OSD menu system is used, OSD ON will appear in the Main Information Display Y and the OSD Indicator P will light to remind you that a video display must be used. When the semi-OSD system is used in conjunction with the discrete configuration buttons, the on- screen display will show a single line of text with the current menu selection. That selection will also be shown in the Main Information Display Y.

Setting the System Configuration Memory

The AVR 520 features an advanced memory system that enables you to establish different configurations for the speaker configuration, digital input, surround mode, delay times, crossover frequency and output levels for each input source. This flexibility enables you to custom-tailor the way in which you listen to each source and have the AVR 520 memorize those settings. This means, for example, that you may use different output levels or trims for different sources, or set different speaker con- figurations with the resultant changes to the bass management system. Once these settings are made, they will automatically be recalled whenever you select that input.

The factory default settings for the AVR 520 have all inputs except for DVD configured for an analog audio input except for the DVD input, where the Coaxial Digital Input 32 is the default. The default speaker settings are for “Large” speakers at the front left/right, “Small” at all other positions, and for the Subwoofer set as being on. However, once the DSP processing system is used for the first time for any input, the speaker settings will auto- matically default to “Small” at all positions with the subwoofer set to “LFE.” The default setting for the surround modes is “Surround Off,” or two-channel stereo, although Dolby Digital or DTS will automatically be selected as appropriate when a source with digital encod- ing is in use.

Before using the unit, you will probably want to change the settings for most inputs so that they are properly configured to reflect the use of digital or analog inputs, the type of speakers installed and the surround mode specifics of your home theater system. Remember that

19SYSTEM CONFIGURATION

Image 19
Contents AVR 520 Audio/ Video Receiver AVR 520 Audio/ Video Receiver On-screen menu and display system Description and FeaturesIntroduction Multiple digital inputs and outputsImportant Safety Information Safety InformationUnpacking Front Panel Controls DTS-ES 6.1 Discrete Main Information Display ˜ into the AVR 520’s memoryFront Panel Controls Front Panel Information Display Main Information Display Z Mute IndicatorDigital soundtrack has been selected Front Panel Information Display ∞ Subwoofer Output § DVD Audio Inputs · AC Power Cord ¶ CD Inputs‚ 8-Channel Direct Inputs When an Rear Panel ConnectionsRear Panel Connections See pages 42-43 for a list of these functions Main Remote Control FunctionsOFF Dialog center channel intelligibility at low volume levelsPreset Up/Down When the tuner is Zone II Remote Control Functions Video Equipment Connections System InstallationAudio Equipment Connections Connect the analog output of a CD player to the CD Inputs ¶System and Power Connections Installation and ConnectionsSpeaker Selection and Placement System ConfigurationSpeaker Placement Making Configuration Adjustments System SetupPlug the AC Power Cord · into an unswitched AC outlet Using the On-Screen DisplaySurround Setup Input SetupTo return to the Master menu Surround Button p Speaker SetupIf no subwoofer is connected to Delay SettingsUsing EzSet Output Level AdjustmentAdditional Input Adjustments AVR 520 off using the Main Power SwitchOperation Surround Mode ChartVMAx Far No delay availableIn-phase material of the left and right channels Medium sized Hall 2 concert hall VMAx NearTurning the AVR 520 On or Off Volume ControlSurround Mode Selection Basic OperationDolby Digital Digital Audio PlaybackSelecting a Digital Source Addition to the bitstream indicators, Digital Status IndicatorsNight Mode Station Selection Tuner OperationPCM Audio Playback MP3 Audio PlaybackTape Recording Output Level Trim AdjustmentPreset Tuning Recalling Preset StationsChannel/8-Channel Direct Input Memory BackupSemi-OSD Settings Advanced FeaturesTurn-On Volume Level To enter this settingFull-OSD Time-Out Adjustment Multiroom Operation Multiroom SetupInstallation Multiroom OperationLearning Codes Programming the RemoteMacro Programming Programming the RemoteAVR 520 Remote Erasing Learned CodesProgrammed Device Functions Erasing Macro CommandsMode Selector/Channel Down Button k Within ten seconds, press the SurroundChannel Control Punch-Through Volume Punch-ThroughTransport Control Punch-Through Reassigning Device Control Selectors Resetting the Remote MemoryPress the 3 Button r three times Function List Tune Down Preset UpPreset Down ClearSetup Code Table TV 031 011 030 033044 100 107 115 154 160 167 168 176Setup Code Table VCR 026 037 039 166074 078 086 125 150 167 172Setup Code Table CD 051 138 149 209 038 045 046 171 175 202 203036 056 057 064 065 089 090 091 092 096 099 104 212 075 109 119 158 183 204Setup Code Number Setup Code Table TapeSetup Code Table Audio Setup Code Table DVDSetup Code Table SAT Setup Code Table CBL 018 047 048 112 213101 207 072 186Lights, motors or other electrical appliances Troubleshooting GuideProcessor Reset Information from nonencoded programsTechnical Specifications Harman Kardon, Incorporated Part No. J90200022100