Harman-Kardon AVR 520 owner manual Input Setup, Surround Setup

Page 20

System Configuration

since the AVR 520 memorizes the settings for each input individually, you will need to make these adjustments for each input used.

However, once they are made, further adjust- ment is only required when system components are changed.

To make this process as quick and as easy as possible, we suggest that you use the full-OSD system with the on-screen menus, and step through each input. Once you have completed the settings for the first input, many settings may be duplicated for the remaining inputs. It is also a good idea to set the configuration data in the order these items are listed in the MASTER menu, as some settings require a specific entry in a prior menu item. Remember that once the settings are made for one input, they must be made for all other input sources in your system.

Input Setup

The first step in configuring the AVR 520 is to configure each input. When using the full-OSD system to make the setup adjustments, press the OSD Button v once so that the MAS- TER menu (Figure 1) appears. Note that the

cursor will be next to the IN/OUT SETUP line. Press the Set Button p to enter the menu and the IN/OUT SETUP menu (Figure 2) will appear on the screen. Press the /Buttons o 37 until the desired input name appears in the highlighted video, as well as being indicated in the front panel Input Indicators by the green LED next to the desired input name. If the input will use the standard left/right analog inputs, no further adjustment is needed.

* I N / O U T S E T U P *

I N P U T

 

:

V I D E O 1

 

 

 

 

 

D I G I T A L

I N :

A N A L O G

 

C O A X I A L

3

:

I N

O U T

 

 

 

 

 

 

 

V I D E O 4

 

:

I N

O U T

B A C K T O

M A S T E R M E N U

Figure 2

If you wish to associate one of the digital inputs with the selected input source, press the

¤Button n on the remote while the IN/OUT SETUP menu (Figure 2) is on the screen, and note that the on-screen cursor will drop down to the DIGITAL IN line. Press the /Buttons o 37 until the name of the desired digital input appears. To return to the analog input, press the buttons

until the word ANALOG appears. When the correct input source appears, press the ¤ but- ton n once so that the cursor appears next to BACK TO MASTER MENU, and press the Set Button p.

To change the digital input at any time using the discrete function buttons and the semi-OSD system, press the Digital Input Select Button Úq on the front panel or the remote. Within five seconds, make your input selection using the Selector buttons on the front panel 5 or the /¤ n Buttons on the remote until the desired digital or analog input is shown in the Main Information Display Y and in the lower third of the video display connected to the AVR 520. Press the Set Button p to enter the new digital input assignment.

An exclusive Harman Kardon feature is the abil- ity to switch front panel coaxial digital audio and analog audio/video jacks from their normal use as inputs to output connections so that portable recording devices may easily be con- nected. On the AVR 520, the Digital Coax 3 Jack Ó is normally an input, but this may also be switched to a digital output for use with CD-R/RW decks, MD recorders or other A/V recorders. To change the jack to an output, press the /¤ Buttons n while the IN/OUT SETUP menu is on the screen until the cursor is next to COAXIAL 3. Then press the /Buttons o 37 so that

the word OUT is highlighted. Note that the Input/Output Status Indicator ( will turn red, indicating that the jack is now a record output.

NOTE: A signal will be sent to this jack only when the input selected for use by the AVR 520 is digital. Digital signals will be passed through regardless of their format, and which digital input (optical or coax) they are fed from. However, analog signals are not converted to digital, and the format of the signal (e.g., PCM, Dolby Digital or DTS) may not be changed.

Selection of the front panel jacks as an output will remain effective as long as the AVR 520 is on. Once the unit is turned off, the jacks will revert to their normal use as an input when the unit is turned on again.

The front panel analog Video 4 Inputs Ô are normally set as an input for use with cam- corders, video games and other portable audio/video products, but they may be switched to an output for connection to portable audio/video recorders. To temporarily switch

them to outputs, you must first be at the IN/OUT SETUP menu. Press the ¤ Button n until the on-screen cursor is pointing to the VIDEO 4 line. Press the Button 37 so that the word OUT is high- lighted. Note that the Input/Output Status Indicator ( between the S and Composite video jacks will turn red, indicating that the analog Video 4 jacks are now record outputs.

Surround Setup

Once the basic input setup has been completed, the next step is to set the surround mode you wish to use with an input. Since surround modes are a matter of personal taste, feel free to select any mode you wish – you may change it later. However, to make it easier to establish the initial parameters for the AVR 520, it is best to select Dolby Pro Logic II or Logic 7 for most analog inputs and Dolby Digital for inputs con- nected to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo (“Surround off”) as they are not typically used with multi- channel program material, where it is unlikely that surround-encoded material will be used. Alternatively, the Logic 7 Music mode is a good choice for stereo-only source material.

It is easiest to complete the surround setup using the full-OSD on-screen menus. From the MASTER menu (Figure 1), press the /¤ Buttons n until the cursor is next to the SURROUND SELECT menu. Press the Set Button p so that the SURROUND SELECT menu (Figure 3) is on the screen.

* S U R R O U N D

S E L E C T *

 

 

S U R R M O D E :

5 . 1

6 . 1 / 7 . 1

D O L B Y

 

 

 

D T S

 

 

 

L O G I C

7

 

 

D S P (

S U R R )

 

 

S T E R E

O

 

 

B A C K T O M A S T E R M E N U

Figure 3

The first line on the SURROUND SELECT menu allows you to configure the AVR for either standard 5.1 or advanced 6.1/7.1 operation. With the on-screen cursor at the SURR MODE line, press the Set Button p and then press the or Buttons o 37 so that 5.1 is highlighted if you have five surround speakers installed, or 6.1/7.1 if you have one or two speakers connected to the Surround Back Preamp Outputs 38 through optional, external power amplifiers.

20SYSTEM CONFIGURATION

Image 20
Contents AVR 520 Audio/ Video Receiver AVR 520 Audio/ Video Receiver Description and Features IntroductionMultiple digital inputs and outputs On-screen menu and display systemUnpacking Safety InformationImportant Safety Information Front Panel Controls Main Information Display ˜ into the AVR 520’s memory DTS-ES 6.1 DiscreteFront Panel Controls Digital soundtrack has been selected Main Information Display Z Mute IndicatorFront Panel Information Display Front Panel Information Display § DVD Audio Inputs · AC Power Cord ¶ CD Inputs ‚ 8-Channel Direct Inputs When anRear Panel Connections ∞ Subwoofer OutputRear Panel Connections Main Remote Control Functions See pages 42-43 for a list of these functionsDialog center channel intelligibility at low volume levels OFFPreset Up/Down When the tuner is Zone II Remote Control Functions System Installation Audio Equipment ConnectionsConnect the analog output of a CD player to the CD Inputs ¶ Video Equipment ConnectionsInstallation and Connections System and Power ConnectionsSpeaker Placement System ConfigurationSpeaker Selection and Placement System Setup Plug the AC Power Cord · into an unswitched AC outletUsing the On-Screen Display Making Configuration AdjustmentsInput Setup Surround SetupTo return to the Master menu Button p Speaker Setup SurroundDelay Settings If no subwoofer is connected toOutput Level Adjustment Using EzSetAVR 520 off using the Main Power Switch Additional Input AdjustmentsSurround Mode Chart OperationNo delay available In-phase material of the left and right channelsMedium sized Hall 2 concert hall VMAx Near VMAx FarVolume Control Surround Mode SelectionBasic Operation Turning the AVR 520 On or OffSelecting a Digital Source Digital Audio PlaybackDolby Digital Night Mode Digital Status IndicatorsAddition to the bitstream indicators, Tuner Operation PCM Audio PlaybackMP3 Audio Playback Station SelectionOutput Level Trim Adjustment Preset TuningRecalling Preset Stations Tape RecordingMemory Backup Channel/8-Channel Direct InputAdvanced Features Turn-On Volume LevelTo enter this setting Semi-OSD SettingsFull-OSD Time-Out Adjustment Multiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote Learning CodesProgramming the Remote AVR 520 RemoteErasing Learned Codes Macro ProgrammingErasing Macro Commands Mode Selector/Channel Down Button kWithin ten seconds, press the Surround Programmed Device FunctionsTransport Control Punch-Through Volume Punch-ThroughChannel Control Punch-Through Press the 3 Button r three times Resetting the Remote MemoryReassigning Device Control Selectors Function List Preset Up Preset DownClear Tune DownSetup Code Table TV 011 030 033 044 100 107 115 154 160 167 168176 031Setup Code Table VCR 166 074 078 086125 150 167 172 026 037 039Setup Code Table CD 038 045 046 171 175 202 203 036 056 057 064 065 089 090 091 092 096 099 104 212075 109 119 158 183 204 051 138 149 209Setup Code Table Tape Setup Code Table AudioSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 112 213 101 207072 186 018 047 048Troubleshooting Guide Processor ResetInformation from nonencoded programs Lights, motors or other electrical appliancesTechnical Specifications Harman Kardon, Incorporated Part No. J90200022100