Harman-Kardon AVR 520 owner manual Multiroom Operation, Multiroom Setup, Installation

Page 36

Multiroom Operation

The AVR 520 is fully equipped to operate

as the control center for a multiroom system with optional remote external infrared (IR) sen- sors, speakers and power amplifiers. Although some multiroom installations will require the services of a specially trained installer, it is pos- sible for the average do-it-yourself hobbyist to install a simple remote room system.

Installation

The key to remote room operation is to link the remote room to the AVR 520’s location with wire for an infrared link and speakers or an amplifier. For installation instructions for Multiroom use, see page 16.

Multiroom Setup

Once the audio and IR link connections have been made, the AVR 520 needs to be configured for multiroom operation using the steps below. Press the OSD Button v to bring the MASTER menu (Figure 1) to the screen. Press the ¤ Button n five times, until the on-screen cursor is next to the MULTI- ROOM line. Press the Set Button p to enter the MULTI-ROOM menu (Figure 10).

*

M U L T I - R O O M *

 

 

M U L T I - R O O M :

O F F

O N

M U L T I I N

: F M P R E S E T 0 1

M U L T I

V O L

:

 

 

B A C K

T O M A S T E R

M E N U

Figure 10

When the MULTI-ROOM menu appears, the on-screen cursor will be at the MULTI-ROOM line. Since this line is used to turn the system on and off, do not make an adjustment here unless you wish to turn the system on at this time. To turn the system on, press the Button 37 so that ON is high- lighted. If you do not wish to turn the system on at this time or to proceed to the next step, press the ¤ Button n once so that the on-screen cursor is next to the MULTI IN line.

At the MULTI IN line, press the /Buttons o31 until the desired input to the multiroom system appears in the highlighted video. When the selection has been made, press the ¤ Button n once so that the

on-screen cursor is next to the MULTI VOL line.

At the MULTI VOL line, press the /Buttons o 37 until the desired volume level for the multiroom system is entered. DO NOT use the regular volume control knobs for this setting. When all settings for the multiroom setup have been made, press the /¤ Buttons n until the on-screen cursor is next to the RETURN TO MASTER MENU line. If you have no other adjustments to make, press the OSD Button v to exit the menu system.

Multiroom Operation

When operating the AVR 520 from a remote room location where an IR sensor link has been connected to the AVR 520’s rear panel Multiroom IR Input f, you may use either the main remote control or the Zone II remote. To turn on the multiroom feed, press any of the Input Selector buttons on the Zone II remote ∫ç∂ or the main remote efg. Press the AVR Selector f∫ to turn the unit on to the last source, or any of the other Selector buttons to turn on to a specific source.

As long as an IR feed to the AVR 520 has been established from the remote room, using any of the buttons on either remote will control the remote location volume 40 î, change the

tuner frequency , change the tuner preset 33 © or mute the output 43 ˚.

If the Remote IR Output Jack d on the AVR 520 is connected to an IR Input jack on compatible Harman Kardon audio components such as CD, DVD or cassette players, the trans- port functions of those machines may also be controlled using the Transport Controls

z28 Ƀ©˙∆ on either remote control.

To turn the system off from the remote room, press the Power Off Button . Remember that the AVR 520 may be turned on or off from the remote room, regardless of the system’s operation or status in the main room.

NOTE: When the tuner is selected as the source for the remote zone, any change to the fre- quency or preset will also change the station being listened to in the main room, if the tuner is in use there. Similarly, if someone in the main room changes the station, the change will also impact the remote room.

To activate the feed to the remote room, while you are in the main listening room where the AVR 520 is located, press the Multiroom

Button 39 on the remote. Next, press the Set Button p. Press the / ¤ Buttons

nto turn the multiroom feed on or off. When the multiroom system is on, the Multi Indicator O will light in the Main Information Display ˜, and the Main Information Display Y or OSD will display MULTI ON. Press the Set Button p to enter the setting.

When the multiroom system is turned on, the input selected using the multiroom menu will be fed to the Multiroom Output Jacks • on the rear panel. The volume will be as set in the previous selection, although it may also be adjusted using an optional IR sensor and the Zone II remote in the remote location or on the optional audio power amplifier connected to the Multiroom Output Jacks •.

Once the multiroom system is turned on, it will remain on even if the AVR 520 is placed in the Standby mode in the main room by pressing the Power Off Button åor the System Power Control 2on the front panel. To turn off the multiroom system, even when the AVR is in Standby mode in the main listening room, press the Multiroom Button 39 and then the Set Button p. Press the / ¤ Buttons

nso that the Multi Indicator O in the Main Information Display ˜goes out, and the Main Information Display Y or OSD will display MULTI OFF. Press the Set Button p to enter the setting and turn the unit off.

Even when the AVR 520 is turned off in the main room, the multiroom system may be turned on at any time by pressing the Multiroom Button 39 , or any of the Selector Buttons ∫ç∂ in the remote room.

36MULTIROOM OPERATIONS

Image 36
Contents AVR 520 Audio/ Video Receiver AVR 520 Audio/ Video Receiver Description and Features IntroductionMultiple digital inputs and outputs On-screen menu and display systemSafety Information Important Safety InformationUnpacking Front Panel Controls Main Information Display ˜ into the AVR 520’s memory DTS-ES 6.1 DiscreteFront Panel Controls Main Information Display Z Mute Indicator Front Panel Information DisplayDigital soundtrack has been selected Front Panel Information Display § DVD Audio Inputs · AC Power Cord ¶ CD Inputs ‚ 8-Channel Direct Inputs When anRear Panel Connections ∞ Subwoofer OutputRear Panel Connections Main Remote Control Functions See pages 42-43 for a list of these functionsDialog center channel intelligibility at low volume levels OFFPreset Up/Down When the tuner is Zone II Remote Control Functions System Installation Audio Equipment ConnectionsConnect the analog output of a CD player to the CD Inputs ¶ Video Equipment ConnectionsInstallation and Connections System and Power ConnectionsSystem Configuration Speaker Selection and PlacementSpeaker Placement System Setup Plug the AC Power Cord · into an unswitched AC outletUsing the On-Screen Display Making Configuration AdjustmentsInput Setup Surround SetupTo return to the Master menu Button p Speaker Setup SurroundDelay Settings If no subwoofer is connected toOutput Level Adjustment Using EzSetAVR 520 off using the Main Power Switch Additional Input AdjustmentsSurround Mode Chart OperationNo delay available In-phase material of the left and right channelsMedium sized Hall 2 concert hall VMAx Near VMAx FarVolume Control Surround Mode SelectionBasic Operation Turning the AVR 520 On or OffDigital Audio Playback Dolby DigitalSelecting a Digital Source Digital Status Indicators Addition to the bitstream indicators,Night Mode Tuner Operation PCM Audio PlaybackMP3 Audio Playback Station SelectionOutput Level Trim Adjustment Preset TuningRecalling Preset Stations Tape RecordingMemory Backup Channel/8-Channel Direct InputAdvanced Features Turn-On Volume LevelTo enter this setting Semi-OSD SettingsFull-OSD Time-Out Adjustment Multiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote Learning CodesProgramming the Remote AVR 520 RemoteErasing Learned Codes Macro ProgrammingErasing Macro Commands Mode Selector/Channel Down Button kWithin ten seconds, press the Surround Programmed Device FunctionsVolume Punch-Through Channel Control Punch-ThroughTransport Control Punch-Through Resetting the Remote Memory Reassigning Device Control SelectorsPress the 3 Button r three times Function List Preset Up Preset DownClear Tune DownSetup Code Table TV 011 030 033 044 100 107 115 154 160 167 168176 031Setup Code Table VCR 166 074 078 086125 150 167 172 026 037 039Setup Code Table CD 038 045 046 171 175 202 203 036 056 057 064 065 089 090 091 092 096 099 104 212075 109 119 158 183 204 051 138 149 209Setup Code Table Tape Setup Code Table AudioSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 112 213 101 207072 186 018 047 048Troubleshooting Guide Processor ResetInformation from nonencoded programs Lights, motors or other electrical appliancesTechnical Specifications Harman Kardon, Incorporated Part No. J90200022100