Harman-Kardon AVR 520 owner manual Output Level Adjustment, Using EzSet

Page 24

System Configuration

* * D E L A Y A D J U S T * *

C E N T E R D E L A Y : 5 M S

S U R R

D E L A Y :

1 0 M S

B A C K

T O M A S T E R M E N U

Figure 6

If the Dolby Digital mode is selected, the CENTER DELAY line is where the first adjustment is made. In that case, press the ‹/›

Buttons o 37 until the number calculated using the formula shown above appears in the display. When the CENTER DELAY is entered, press the ¤ Button n once to move to the next line.

When the CENTER DELAY is set, or if the Dolby Pro Logic II mode is selected, the › cursor will be at the SURR DELAY line so that the delay for the surround speakers may be set. Press the ‹/› Buttons o 37 until the number calculated using the formula shown above appears in the display. When the delay settings are complete, press the ¤ Button n once so that the cursor is next to the BACK TO MASTER MENU line and press the Set Button p to return to the MASTER menu.

Output Level Adjustment

Output level adjustment is a key part of the configuration of any surround-sound product. It is particularly important for a digital receiver such as the AVR 520, as correct outputs ensure that you hear sound tracks with the proper directionality and intensity.

IMPORTANT NOTE: Listeners are often con- fused about the operation of the surround channels. While some assume that sound should always be coming from each speaker, most of the time there will be little or no sound in the surround channels. This is because they are only used when a movie director or sound mixer specifically places sound there to create ambience, a special effect or to continue action from the front of the room to the rear. When the output levels are properly set, it is normal for surround speakers to operate only occasionally. Artificially increasing the volume to the rear speakers may destroy the illusion of an enveloping sound field that duplicates the way you hear sound in a movie theater or concert hall.

Before beginning the output level adjustment process, make certain that all speaker connec- tions have been properly made. The system volume should be set to the level that you will use during a typical listening session. Finally, make certain that the Balance Control Ò is set to the center “12 o’clock” position.

Using EzSet

Harman Kardon’s exclusive EzSet remote makes it possible to quickly and accurately set the AVR 520’s output levels without the use of a sound pressure meter, although manual adjust- ment is also available. However, for the easiest set-up, follow these steps while seated in the listening position that will be used most often:

1.Make certain that all speaker positions have been properly configured for their “large” or “small” settings (as outlined above) and turn off the OSD system if it is in use.

2.Adjust the volume so that it is at -15, as shown in the on-screen display or Main Information Display Y.

3.Hold the remote in front of you at arm’s length, being sure not to cover the EzSet Sensor Microphone 44 at the top of the remote.

4.Press and hold the SPL Indicator Select Button 41 for three seconds. Release it when the Program/SPL Indicator c stops flashing and and remains lit. Within five seconds, press the 5 Button r on the remote if your system is configured for 5.1 operation with standard speakers or the 7 Button r on the remote if your system is configured for 6.1/7.1 operation with a full speaker complement including rear surround speakers. Once the correct channel configuration button has been pressed the test noise will be heard from the front left speaker.

5.At this point, EzSet will take over, adjusting the output level of each channel so that when the process is complete all levels will be equal and at the set reference point. This process may take a few minutes, depending on the extent of adjustment required.

6.During the adjustment, you will see the location of the channel position being adjusted appear in the on-screen display (if connected) in the Main Information Display Y, alternating with a readout of the output setting, rela-

tive to the reference volume level, and in the Speaker/Channel Input Indicators

Q where the letters for the channel being adjusted will flash to indicate from which channel the test tone should be heard. As the adjustment proceeds, a few things will happen simultaneously:

•The channel position being adjusted will flash in the Speaker/Channel Input Indicators Q. If the test noise is heard from a channel other than the one shown in the Indicator, there is an error in the speaker connections. If this is the case, press the Test Button iTWICE to stop the adjustment. Then, turn the unit off and verify that all speakers are con- nected to the proper Outputs nop and that any connections made to rear surround speakers powered by optional amplifiers through the Preamp Outputs 38 are correct.

•As the individual channels are set, the channel name and the adjustment offset will appear in the on-screen display (if connected) and the Main Information Display Y. While the level is changing, the Program/SPL Indicator c will change colors to reflect the output level in relation to the reference. A red indica- tion shows that the level is too high, while an amber indication shows that the level is too low. When the indicator is green, the level is correct, and the test noise will move to the next channel.

•While adjustments are being made, the red LED under the AVR Selector f will flash. This is normal, and indicates that EzSet is operating.

7.After the test noise has circulated once through each channel, it will send the tone to each channel once again, to verify the settings.

8.After two complete circulations of the tone, the levels are set. The Program/SPL Indicator c will remain green at each channel. Upon completion of the second circulation, the Program/SPL Indicator c will flash green twice and then go out. The tone will stop and the AVR 520 will return to normal operation.

If you find that the output levels chosen by EzSet are either uncomfortably low or high, you may repeat the procedure. Return to Step 2 and adjust the master volume either slightly higher or lower to accommodate your particular room layout and your tastes. You may repeat this pro-

24SYSTEM CONFIGURATION

Page 23 Page 25
Image 24
Page 23 Page 25
Contents AVR 520 Audio/ Video Receiver AVR 520 Audio/ Video Receiver Description and Features IntroductionMultiple digital inputs and outputs On-screen menu and display systemSafety Information Important Safety InformationUnpacking Front Panel Controls Main Information Display ˜ into the AVR 520’s memory DTS-ES 6.1 DiscreteFront Panel Controls Main Information Display Z Mute Indicator Front Panel Information DisplayDigital soundtrack has been selected Front Panel Information Display § DVD Audio Inputs · AC Power Cord ¶ CD Inputs ‚ 8-Channel Direct Inputs When anRear Panel Connections ∞ Subwoofer OutputRear Panel Connections Main Remote Control Functions See pages 42-43 for a list of these functionsDialog center channel intelligibility at low volume levels OFFPreset Up/Down When the tuner is Zone II Remote Control Functions System Installation Audio Equipment ConnectionsConnect the analog output of a CD player to the CD Inputs ¶ Video Equipment ConnectionsInstallation and Connections System and Power ConnectionsSystem Configuration Speaker Selection and PlacementSpeaker Placement System Setup Plug the AC Power Cord · into an unswitched AC outletUsing the On-Screen Display Making Configuration AdjustmentsInput Setup Surround SetupTo return to the Master menu Button p Speaker Setup SurroundDelay Settings If no subwoofer is connected toOutput Level Adjustment Using EzSetAVR 520 off using the Main Power Switch Additional Input AdjustmentsSurround Mode Chart OperationNo delay available In-phase material of the left and right channelsMedium sized Hall 2 concert hall VMAx Near VMAx FarVolume Control Surround Mode SelectionBasic Operation Turning the AVR 520 On or OffDigital Audio Playback Dolby DigitalSelecting a Digital Source Digital Status Indicators Addition to the bitstream indicators,Night Mode Tuner Operation PCM Audio PlaybackMP3 Audio Playback Station SelectionOutput Level Trim Adjustment Preset TuningRecalling Preset Stations Tape RecordingMemory Backup Channel/8-Channel Direct InputAdvanced Features Turn-On Volume LevelTo enter this setting Semi-OSD SettingsFull-OSD Time-Out Adjustment Multiroom Setup InstallationMultiroom Operation Multiroom OperationProgramming the Remote Learning CodesProgramming the Remote AVR 520 RemoteErasing Learned Codes Macro ProgrammingErasing Macro Commands Mode Selector/Channel Down Button kWithin ten seconds, press the Surround Programmed Device FunctionsVolume Punch-Through Channel Control Punch-ThroughTransport Control Punch-Through Resetting the Remote Memory Reassigning Device Control SelectorsPress the 3 Button r three times Function List Preset Up Preset DownClear Tune DownSetup Code Table TV 011 030 033 044 100 107 115 154 160 167 168176 031Setup Code Table VCR 166 074 078 086125 150 167 172 026 037 039Setup Code Table CD 038 045 046 171 175 202 203 036 056 057 064 065 089 090 091 092 096 099 104 212075 109 119 158 183 204 051 138 149 209Setup Code Table Tape Setup Code Table AudioSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 112 213 101 207072 186 018 047 048Troubleshooting Guide Processor ResetInformation from nonencoded programs Lights, motors or other electrical appliancesTechnical Specifications Harman Kardon, Incorporated Part No. J90200022100
Top Page Image Contents