Harman-Kardon AVR 520 Reassigning Device Control Selectors, Resetting the Remote Memory

Page 41

Programming the Remote

Reassigning Device Control Selectors

Although each Input Selector e is normally assigned to the category of product shown on the remote, it is possible to reassign one of these buttons to operate a second device of another type. For example, if you have two VCRs but no satellite receiver, you may program the “SAT” button to operate a second VCR. Before following the normal programming steps for either Three-Digit entry or Auto Search code entry, you must first reassign the button with the following steps:

1.Press the Input Selector e you wish to reassign and the Mute Button 43 at the same time until the red light appears under the Input Selector e and the Program/ SPL Indicator c flashes amber.

2.Press the Input Selector e for the device you wish to program into the reassigned button.

3.Enter the three-digit code for the specific model you wish the reassigned button to operate.

4.Press the same Input Selector e pressed in Step 1 once again to store the selection. The red LED under the re-assigned Input Selector will flash three times and then go out.

Example: To use the CBL/SAT button to operate a second VCR, first press the CBL/SAT Input Selector e and the Mute Button 43 at the same time until the red light glows under the CBL/SAT e button. Press the VCR e Button, followed by the three-digit code for the specific model you wish to control. Finally, press the CBL/SAT Button e again.

Resetting the Remote Memory

As you add components to your home-theater system, occasionally you may wish to totally reprogram the remote control without the confu- sion of any commands, macros or ”Punch- Through“ programming that you may have done. To do this, it is possible to reset the remote to the original factory defaults and com- mand codes by following these steps. Note, however, that once the remote is reset, all com- mands or codes that you have entered will be erased and will need to be re-entered:

1.Press any of the Input Selector Buttons e and the ”O“ Button r at the same time until the Program/SPL Indicator c begins to flash amber.

2.Press the ”3“ Button r three times.

3.The red LED under the Input Selector e will go out and the Program/SPL Indicator c will stop flashing and turn green.

4.The Program/SPL Indicator c will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased.

5.When the Program/SPL Indicator c goes out, the remote has been reset to the factory settings.

41PROGRAMMING THE REMOTE

Page 40 Page 42
Image 41
Page 40 Page 42
Contents AVR 520 Audio/ Video Receiver AVR 520 Audio/ Video Receiver Introduction Description and FeaturesMultiple digital inputs and outputs On-screen menu and display systemUnpacking Safety InformationImportant Safety Information Front Panel Controls DTS-ES 6.1 Discrete Main Information Display ˜ into the AVR 520’s memoryFront Panel Controls Digital soundtrack has been selected Main Information Display Z Mute IndicatorFront Panel Information Display Front Panel Information Display ‚ 8-Channel Direct Inputs When an § DVD Audio Inputs · AC Power Cord ¶ CD InputsRear Panel Connections ∞ Subwoofer OutputRear Panel Connections See pages 42-43 for a list of these functions Main Remote Control FunctionsOFF Dialog center channel intelligibility at low volume levelsPreset Up/Down When the tuner is Zone II Remote Control Functions Audio Equipment Connections System InstallationConnect the analog output of a CD player to the CD Inputs ¶ Video Equipment ConnectionsSystem and Power Connections Installation and ConnectionsSpeaker Placement System ConfigurationSpeaker Selection and Placement Plug the AC Power Cord · into an unswitched AC outlet System SetupUsing the On-Screen Display Making Configuration AdjustmentsSurround Setup Input SetupTo return to the Master menu Surround Button p Speaker SetupIf no subwoofer is connected to Delay SettingsUsing EzSet Output Level AdjustmentAdditional Input Adjustments AVR 520 off using the Main Power SwitchOperation Surround Mode ChartIn-phase material of the left and right channels No delay availableMedium sized Hall 2 concert hall VMAx Near VMAx FarSurround Mode Selection Volume ControlBasic Operation Turning the AVR 520 On or OffSelecting a Digital Source Digital Audio PlaybackDolby Digital Night Mode Digital Status IndicatorsAddition to the bitstream indicators, PCM Audio Playback Tuner OperationMP3 Audio Playback Station SelectionPreset Tuning Output Level Trim AdjustmentRecalling Preset Stations Tape RecordingChannel/8-Channel Direct Input Memory BackupTurn-On Volume Level Advanced FeaturesTo enter this setting Semi-OSD SettingsFull-OSD Time-Out Adjustment Installation Multiroom SetupMultiroom Operation Multiroom OperationLearning Codes Programming the RemoteAVR 520 Remote Programming the RemoteErasing Learned Codes Macro ProgrammingMode Selector/Channel Down Button k Erasing Macro CommandsWithin ten seconds, press the Surround Programmed Device FunctionsTransport Control Punch-Through Volume Punch-ThroughChannel Control Punch-Through Press the 3 Button r three times Resetting the Remote MemoryReassigning Device Control Selectors Function List Preset Down Preset UpClear Tune DownSetup Code Table TV 044 100 107 115 154 160 167 168 011 030 033176 031Setup Code Table VCR 074 078 086 166125 150 167 172 026 037 039Setup Code Table CD 036 056 057 064 065 089 090 091 092 096 099 104 212 038 045 046 171 175 202 203075 109 119 158 183 204 051 138 149 209Setup Code Table Audio Setup Code Table TapeSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 101 207 112 213072 186 018 047 048Processor Reset Troubleshooting GuideInformation from nonencoded programs Lights, motors or other electrical appliancesTechnical Specifications Harman Kardon, Incorporated Part No. J90200022100
Top Page Image Contents