Harman-Kardon AVR 445 owner manual Additional Input Adjustments

Page 33

To enter individual settings for a specific channel, first make sure that you have either run EzSet/EQ and/or made any desired manual trim adjustments to set a baseline for all channels. After that is done, press the OSD Button Uto exit the menu system and then select the input for which you wish to enter differ- ent level settings by using either the Input Source Selector 7 on the front panel or the buttons on the remote that are used to select an input source deXhç∂≠ƒ®. Next, return to the CHANNEL ADJUST submenu using the steps outlined above.

At the CHANNEL ADJUST menu, press the /¤ Navigation Button until the cursor is pointing to the CH ADJUST line and then press the /Navigation Button once so that INDEPENDENT appears in highlighted video. When this setting is active you may change the channel output levels for any input without changing the settings previously established for another.

NOTE: With the default GLOBAL setting, output levels are associated with the various surround modes. As you spend time listening to various materials and selecting a variety of surround modes, you may wish to revisit the CHANNEL ADJUST menu to set the output levels.

When all changes to the Channel Output levels and the associated level trim settings have been made, press the /¤ Navigation Button until the cursor is on the BACK TO MANUAL SETUP menu and then pressing the Set Button so that you may make any other adjust- ments to the system parameters. If the changes just made complete the manual adjustments needed, press the OSD Button Uto exit the menu system and resume normal system operation.

Additional Input Adjustments

After one input has been adjusted for Surround mode, digital input (if any), speaker type, and output levels, go back to the IN/OUT SETUP line on the MASTER MENU (Figure 1) and enter the set- tings for each input that you will use. In most cases, only the digital input and surround mode will be differ- ent from one input to the next, while the speaker type, crossover frequency, Night mode and output level settings will usually be the same and may be quickly entered by entering the same data used for the original input.

Once the settings outlined on the previous pages have been made, the AVR 445 is ready for operation. While there are some additional settings to be made, these are best done after you have had an opportunity to lis- ten to a variety of sources and different kinds of pro-

SYSTEM CONFIGURATION

gram material. These advanced settings are described on pages 42 and 43 of this manual. In addition, any of the settings made in the initial configuration of the unit may be changed at any time. As you add new or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown in this section.

Having completed the setup and configuration process for your AVR 445, you are about to experience the finest in music and home theater listening. Enjoy!

SYSTEM CONFIGURATION 33

Image 33
Contents AUDIO/VIDEO Receiver AVRModèle pour les Canadien AVR 445 AUDIO/VIDEO ReceiverIntroduction Description and FeaturesImportant Safety Information Safety InformationFRONT-PANEL Controls 4Tuning Selector Volume ControlFRONT-PANEL Controls Is installedFRONT-PANEL Controls REAR-PANEL Connections CD Audio Inputs Connect these jacks to You wish to controlDVD Video Inputs Connect the composite or Main Remote Control Functions Second press selects the device connected to the Hdmi 2 jack To program the proper codes for the products in your systemMain Remote Control Functions Main Remote Control Functions ZR 10 Remote Control Functions 16 ZR 10 Remote Control Functions System Installation Installation and ConnectionsAudio Equipment Connections Your areaSystem and Power Connections AC Power Connections BUSInstallation ConnectionsRS-232 Connections USB ConnectionsSystem Configuration Subwoofer Placement System Setup+ and polarity indicators that are Using the On-Screen DisplayMaking Configuration Adjustments In/Out SetupSetting the System Configuration Memory › Navigation Button DO U T S E T U P Surround Setup Audio SetupPœ to return to the main menu screen ‹/› Navigation Buttons D once so that 96kHz appearsThree Dolby surround settings are ‹/› Navigation Buttons D to turn the mode on or OFFThen press the Set Button pœ ScreenUsing EzSet/EQ System Configuration So that on is highlighted and then press the Set Button pœ Manual SetupSpeaker Size Speaker Size MenuTo continue with overall configuration Sub Mode Setting LFE Low-Pass-Filter SettingFollowing options are available Subwoofer SizeDelay Adjust Correct channel Setup menuAdditional Input Adjustments Operation Basic OperationSource Selection Surround Mode Selection Volume and Tone ControlDigital Audio Playback Lower Display Line $. Next, useSelecting a Digital Source Dolby DigitalPCM Playback To the AVRNight Mode Speaker/Channel IndicatorsUsing TheBridgeTM AM/FM Tuner OperationXM Radio Operation Recording Front-Panel ConnectionsFor tuner operation have different functions with XM Radio Memory Backup Output Level Trim AdjustmentEzSet/EQ On/Off Dim FunctionAdvanced Features DMP/ TheBridgeTM Auto Power If you wish to make other adjustments, pressInstallation Multiroom SetupMultiroom Operation Surround Channel Amplifier AssignmentInfrared Output Selection Multiroom OperationConfiguring the Remote Preprogrammed Code EntryBottom line Automatic Code Entry Learning CommandsLearning Keys for an Entire Device Remote Learning Codes for an Input SelectorMacro Programming Changing DevicesErasing a Macro Power On VID 2/TV VID 3/Cable AVR Logic 7 hVolume Punch-Through Punch-Through ConfigurationMacro to be erased appears, press the Set Button F Read a MacroReturning the Channel Control Settings to Default Operation Channel Punch-ThroughTransport Punch-Through Renaming a Device RenamingAs shown in Figure CharactersBy pressing a particular button Resetting the RemoteAt this point, you have two options To be reenteredDevice Priority Timing Additional Notes on Configuring and Operating the RemoteBacklight Options To change the device priority timing, follow these stepsW B a T T E R Y Processor Reset Troubleshooting GuideAppendix Surround Mode ChartVideo Default SurroundTuner TapeChannel Adjust Sub ModeVolume Default Volume Default SetFeature DVD AVR 445 Technical Specifications