CONFIGURING THE REMOTE
see whether the remote operates correctly. Although the AVR remote is preprogrammed with an extensive library of codes for many major brands, it is also possi- ble that you may have attempted to program a product that is too new or too old, and thus not all of its com- mands will be in the code library. You may fill in the codes for any button that does not operate properly by using the learning technique shown on this page.
Automatic Code Entry
In addition to manual code selection using the brand name list, it is also possible to automatically search through all the codes that are stored in the AVR remote’s library to see whether a device will respond even if it
is not listed among the brands that appear when you program the remote manually. To automatically search through the codes that are available for a specific device type (e.g., DVD, VCR), follow these steps:
1.Turn on the power to the device you wish to program into the AVR remote. This is important because in a later step you will need to see whether the device turns off to determine whether the remote has been programmed for the proper remote codes.
2.Press and hold the Program Button y for about 3 seconds while the message shown in Figure 25 appears in the remote’s LCD Information Display c. Release the button when the red light under the Set Button F appears.
3.The remote’s MAIN MENU message (Fig. 26) will appear in the LCD and the Set Button F will remain illuminated in red. Press the Set Button Fto begin the process of selecting a device and locating the proper remote codes.
4.SELECT A DEVICE will appear in the LCD (Figure 27). Press the ⁄/ ¤ Navigation Button Dto scroll through the list of device categories and press the Set Button Fwhen the device for which you wish to set the codes appears.
For this example, we will select “TV” to enter the codes needed to operate your TV.
5.At the next menu screen on the remote, press the
⁄Navigation Button Dso that the bottom line of the LCD reads AUTO (Figure 32) and then press the Set Button Fto enter the Automatic programming mode.
P R O G R A M D E V I C E
A U T O
Figure 32
6.As instructed on the next menu screen, press the ⁄ Navigation Button Dto begin the automatic code search process. Your confirmation that the remote is sending out commands is the movement of a square block across the top line
of the LCD screen while the bottom line reads PLEASE WAIT…. You will also see the transmit icon in the upper right corner of the LCD’s top line to remind you that the remote is working even though you may not see anything happening to the device being programmed.
7.It will take a few seconds for the remote to send out the first group of commands, after which you will see a new display in the LCD screen, as shown in Figure 33. Following the instructions, if the device being programmed has not turned off, press the ⁄ Navigation Button Dagain to send another group of codes. If the device being programmed has turned off, skip to Step 9.
P O W E R O F F ?
Y - > 1 ~ 0 N - >
Figure 33
8.By pressing the ⁄ Navigation Button D again, the remote will send out a new set of commands. When it pauses, follow the instructions shown in Step 7. Depending on how many codes are stored for a specific device type, you may have to repeat this process as many as 15 times. Remember, if the device turns off, skip to Step 9. When all the codes for the device being pro- grammed have been tried, the instruction shown in Figure 34 will appear. This means that the codes for the product you are trying to program are not in the AVR remote library and you will have to “learn” them into the remote following the instructions shown in the next section. Press the Set Button Fas instructed to exit the programming process.
R E A C H E N D P O I N T
E X I T - > S E T K E Y
Figure 34
9.If the device being programmed does turn off after following the instructions in Step 7, you will need to verify the code set by pressing the Numeric Keys cin sequence, as instructed in Figure 33. Point the remote at the device being programmed, and press the “1” Button cto see whether the device turns back on.
10.After pressing and releasing the “1” Button c, check to see whether the device has turned back on. If it has, skip to Step 12. If it does not turn off, press the “2” Button c, or the next button in the numeric sequence if you are repeating the procedure, as instructed by the LCD screen in Figure 35.
P O W E R O N ?
Y - > S E T N - > 1 ~ 0
Figure 35
11.When pressing the “1” button does not turn the device being programmed back on, repeat the procedure by trying the remainder of the Numeric Keys cin sequence, each time pressing and then releasing the button to see whether the new device turns back on. When it does, skip to the next step. However, if you try all 10 numeric keys and find that the unit will not turn on, you won’t be able to use this method to program the device. Press the Clear Button j to exit the programming process. You’ll need to follow the Learning Commands instructions below to enter the codes for this device into the AVR remote.
12.When pressing one of the numeric keys in Step 10 or 11 causes the device being programmed to turn back on, follow the instructions shown in Figure 33 and press the Set Button Fwithin five seconds of the device turning on. After you press the Set button, the top line of the LCD will read SAVING… and then the word SAVED will flash four times in the center of the bottom line.
13.When the codes are saved, the remote will return to normal operation, and whenever you press the Input Selector Button d that was just programmed, the codes for the new device will be used. If no further buttons are pressed, the remote will revert back to the default setting for AVR commands.
Learning Commands
On occasions when the AVR remote does not contain the codes for a particular product’s remote in its built- in library, or when you wish to program a missing or special function into one button of a device, the AVR remote’s learning capability allows you to do that. To teach commands from one product’s remote into the AVR remote:
The AVR 445’s remote not only allows you to “learn” in the commands from any compatible remote; it also allows you to learn a separate code into the Input Selector Buttons d. This unique capability allows you to configure the remote so that whenever one of these buttons is pressed, the remote will not only select the codes for that device for itself, but it will transmit a separately programmed remote code. By programming the display’s input selection remote code for the specific device, you can, for example, press the VID 3/Cable Input Selector Button d and not only have the AVR switch to a cable
Before learning codes, note that all buttons on the remote may have a command “learned” except for Clear j, Program y, Light z and the Macro Buttons R.
CONFIGURING THE REMOTE 47