Harman-Kardon AVR 445 owner manual Power On VID 2/TV VID 3/Cable AVR Logic 7 h, Erasing a Macro

Page 50

CONFIGURING THE REMOTE

Recording a Macro

To record a macro into the remote’s memory, follow these steps:

1.Press and hold the Program Button y for about three seconds while the message shown in Figure 25 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button F appears.

2.The remote’s MAIN MENU message (Figure 26), will appear in the LCD and the Set Button Fwill remain illuminated in red. Press the Navigation Button Dso that MACRO appears on the bottom line of the LCD, as shown in Figure 48. Press the Set Button Fto enter the main macro menu branch.

M A I N M E N U

M A C R O

Figure 48

3.At the next menu screen (Figure 49) press the Set Button Fto begin recording a macro.

M A C R O

R E C O R D A M A C R O

Figure 49

4.The next display screen (Figure 50) is where you select the button that will be used to recall the macro. The choices are the Power On Button 1or one of the discrete Macro Buttons R. Press the / ¤ Navigation Button Duntil the name of the button you wish to program the macro into is shown. For this example we will show how to program a series of commands that will automatically be sent out every time the Power button is pressed.

R E C O R D A M A C R O

P O W E R O N

Figure 50

5.The next screen that appears (Figure 51) is where you select the device for the first command that will be sent out as part of the macro. Press the / ¤ Navigation Button Duntil the name of the device appears on the left side of the lower line in the LCD. For this example, the first button we want to have the macro “press” is the Power On button, so the AVR device is selected. Press the Set Button Fwhen the desired device name appears to move to the next programming step.

S E L E C T A D E V I C E

A V R

Figure 51

6.The next display (Figure 52) is where you begin entering the individual commands for the macro,

in the order you wish them to be transmitted. Remember that when you want to change devices, you must first press the Input Selectors d for that button, and then press the Command or Function key. Since we want to program a series of events that occur each time the Power On button is pressed, press the AVR button. In your specific macro, this is the first command button.

S E L E C T A D E V I C E

A V R

Figure 52

7.The next display (Figure 53) and the subsequent screens are where the actual macro programming takes place. The words at the left side of the top line of the display show the button that is being programmed (e.g., the Power On Button 1or one of the Macro Buttons R) and the indica- tion at the right side of the top line shows the number of macro steps available of 20 possible steps. Following the instructions on the remote’s LCD screen, press the first key you wish to be transmitted in the macro. In our example, we first want the AVR 445 to turn on, so the Power Button 1should be pressed.

P O W E R O N

0 0 / 2 0

S E L E C T K E Y P R E S S

Figure 53

8.Once the first command button for the macro has been pressed, continue to press the buttons you wish to be part of the macro, in the order they will be used. Press each button within five seconds of the last button, remembering to press the Input Selector 3when you are changing device functions. As the buttons on the remote are pressed, the remote’s display screen will show the steps in the macro as they are programmed (Figure 54).

[ A V R ]

[ A V R ] P O W E R O N

Figure 54

9.For our example, we first want the AVR Power On button pressed, followed by the TV Power On, followed by the Cable Box On, followed by the selection of the Logic 7 mode. To do that, press the buttons in this order:

Power On 1

VID 2/TV 3

Power On 1

VID 3/Cable 3

Power On 1

AVR 4

Logic 7 h

As each button is pressed to enter it into the macro, you will see the button names appear and then scroll up on the LCD as your confirmation of the key entry (Figure 54).

10.When all commands for the macro have been entered, press the Set Button Fto save the macro. The display screen will show the button to which the macro has been programmed and the number of steps used, and the word SAVED will blink four times in the lower line of the LCD. When the display returns to normal, the macro has been entered and the remote is ready for operation.

11.If a macro has been programmed into the Power On Button 1, it will play back anytime the Power On button is pressed. As the macro plays, you will see the steps appear in the remote’s LCD. Macros programmed into one of the four discrete Macro buttons may be activated at any time by pressing the appropriate button.

Erasing a Macro

Once a macro has been created and stored in the AVR remote’s memory, you have the option of erasing it. You may do this at any time by following these steps:

1.Press and hold the Program Button Ofor about three seconds while the message shown in Figure 25 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button F appears.

2.The remote’s MAIN MENU message (Figure 26), will appear in the LCD and the Set Button Fwill remain illuminated in red. Press the

Navigation Button Dso that MACRO appears on the bottom line of the LCD screen, as shown in Figure 48. Press the Set Button Fto enter the main macro menu branch.

3.At the next menu screen (Figure 55), press the

/ ¤ Navigation Button Duntil the bottom line in the remote’s LCD reads ERASE A MACRO. Press the Set Button Fto begin the process of erasing a macro.

M A C R O

E R A S E A M A C R O

Figure 55

4.The next display screen (Figure 56) is where you select which macro will be erased. Press the / ¤ Navigation Button Duntil the number of the macro you wish to erase appears. For this example, we will erase the Power On macro created in the previous section. When the name

50 CONFIGURING THE REMOTE

Image 50
Contents AVR AUDIO/VIDEO ReceiverAVR 445 AUDIO/VIDEO Receiver Modèle pour les CanadienDescription and Features IntroductionSafety Information Important Safety Information4Tuning Selector Volume Control FRONT-PANEL ControlsIs installed FRONT-PANEL ControlsFRONT-PANEL Controls REAR-PANEL Connections You wish to control CD Audio Inputs Connect these jacks toDVD Video Inputs Connect the composite or Main Remote Control Functions To program the proper codes for the products in your system Second press selects the device connected to the Hdmi 2 jackMain Remote Control Functions Main Remote Control Functions ZR 10 Remote Control Functions 16 ZR 10 Remote Control Functions Audio Equipment Connections Installation and ConnectionsSystem Installation Your areaSystem and Power Connections RS-232 Connections BUSInstallation ConnectionsAC Power Connections USB ConnectionsSystem Configuration + and polarity indicators that are System SetupSubwoofer Placement Using the On-Screen DisplaySetting the System Configuration Memory In/Out SetupMaking Configuration Adjustments › Navigation Button DO U T S E T U P Pœ to return to the main menu screen Audio SetupSurround Setup ‹/› Navigation Buttons D once so that 96kHz appearsThen press the Set Button pœ ‹/› Navigation Buttons D to turn the mode on or OFFThree Dolby surround settings are ScreenUsing EzSet/EQ System Configuration Manual Setup So that on is highlighted and then press the Set Button pœSpeaker Size Menu Speaker SizeFollowing options are available LFE Low-Pass-Filter SettingTo continue with overall configuration Sub Mode Setting Subwoofer SizeDelay Adjust Setup menu Correct channelAdditional Input Adjustments Source Selection OperationBasic Operation Digital Audio Playback Volume and Tone ControlSurround Mode Selection Lower Display Line $. Next, useDolby Digital Selecting a Digital SourceTo the AVR PCM PlaybackSpeaker/Channel Indicators Night ModeXM Radio Operation Using TheBridgeTMAM/FM Tuner Operation For tuner operation have different functions with XM Radio RecordingFront-Panel Connections EzSet/EQ On/Off Output Level Trim AdjustmentMemory Backup Dim FunctionAdvanced Features If you wish to make other adjustments, press DMP/ TheBridgeTM Auto PowerMultiroom Operation Multiroom SetupInstallation Surround Channel Amplifier AssignmentMultiroom Operation Infrared Output SelectionBottom line Configuring the RemotePreprogrammed Code Entry Learning Commands Automatic Code EntryLearning Codes for an Input Selector Learning Keys for an Entire Device RemoteChanging Devices Macro ProgrammingPower On VID 2/TV VID 3/Cable AVR Logic 7 h Erasing a MacroMacro to be erased appears, press the Set Button F Punch-Through ConfigurationVolume Punch-Through Read a MacroTransport Punch-Through Returning the Channel Control Settings to Default OperationChannel Punch-Through As shown in Figure RenamingRenaming a Device CharactersAt this point, you have two options Resetting the RemoteBy pressing a particular button To be reenteredBacklight Options Additional Notes on Configuring and Operating the RemoteDevice Priority Timing To change the device priority timing, follow these stepsW B a T T E R Y Troubleshooting Guide Processor ResetSurround Mode Chart AppendixTuner Default SurroundVideo TapeVolume Default Sub ModeChannel Adjust Volume Default SetFeature DVD AVR 445 Technical Specifications