Harman-Kardon AVR 445 owner manual Recording, Front-Panel Connections

Page 40

OPERATION

Once you have purchased the XM module, follow the instructions accompanying it to activate the XM Service. Connect the plug on the XM module to the XM Ready Input V on the rear panel of the AVR

445.For best results, point the antenna module out a window, again, following the instructions packed with the XM product. If a window view is not available for the antenna, XM Radio operates a series of terrestrial repeater stations that may be able to provide recep- tion, though this service is not available everywhere.

IMPORTANT NOTE: XM Radio requires both the optional, external antenna module and a sub- scription to the XM Radio service. Antenna and service sold separately; XM Radio is not avail- able in Alaska or Hawaii.

If you need to view the antenna module’s number, connect it to the AVR and then follow one of the steps shown below to select XM Radio as the input source. Tune to “000” to get a readout of the number.

Once you have an activated module connected, follow one of these steps to select XM Radio as your sys- tem’s audio source:

From the front panel, press the Input Source Selector 6. If XM was the last-used tuner source, it will appear; or press the button again until XM Radio is heard. Press the Tuning Selector 3 to change stations within a frequency band. Press the Tuning Selector 3 to select a different XM channel.

From the main remote, press the Tuner/FM Select Button Xby pressing the button up towards the top of the remote as needed until XM Radio is shown as the source. To change stations, press the Tuning Up/Down Button M.

To select the tuner from the ZR 10 remote control, press the XM Radio Selector Button ƒ. Channels are selected using the Prev/Next Transport Controls π.

While using XM Radio is similar in many ways to AM/FM terrestrial radio, the wide range of program choices available, as well as the ability of the XM serv- ice to add special data and information tags into the digital audio data stream, means that some of the front-panel and remote controls traditionally used

for tuner operation have different functions with XM Radio.

When XM Radio is the AVR’s source, the channel number will appear in the Upper Display Line C, along with an indication of the Preset number, if any, and a series of bars at the far right end of the dis- play. These bars (not shown in the semi-OSD mes- sage), show the current signal strength similar to the signal strength displays on a cellular phone.

The current channel’s name will normally appear in the Lower Display Line D. For local traffic infor- mation, the name of a city will be shown in place of

the channel name. You may change this display to show the current artist and track title information by pressing the Tuning Mode Selector 7Bø. When you are listening to a channel with local traffic information in the “200” series of channel numbers, these buttons change the display to show the tem- perature and current weather for the selected city.

To tune a channel number directly, simply press the Numeric Keys cΔ. Unlike standard AM/FM tuner operation, it is not necessary to press the Direct button first.

The AVR 445 has five banks of preset memories for XM Radio, each with eight memory positions and designated by a letter (“A” through “E”). To store a channel into a memory group, first press the Set Button Fœ until PRESET SEARCH appears in the Upper Display Line

C and on the top line of the semi-OSD display. Next, press the /Navigation Buttons D

© until the desired preset memory bank letter appears in the Lower Display Line D and in the bottom line of the semi-OSD display. Next, press the Memory Button bñ and note that a dash will start to flash next to the preset memory bank letter. Within five seconds, press the Numeric Button cΔ from 1 to 8 for the memory slot you wish to use.

To tune up or down through a list of channels stored in the currently active preset memory, press the Preset Up/Down Buttons L. You may also use the Preset Station Selector 5 on the front panel, or the Prev/Next Transport Controls π on the ZR 10 remote. To change to another preset bank, press the Set Button Fand then press the /Navigation Buttons HD© until the desired preset memory bank letter appears in the Lower Display Line D and in the bottom line of the semi-OSD display.

Each XM Radio channel is assigned a category, which may be viewed by pressing the Tuning Mode Selector B7ø. You may search for an XM channel in any of the categories by first pressing the Set ButtonFand then pressing the /Navigation Buttons HD© until the desired category name appears in the Lower Display Line D and in the bottom line of the semi-OSD display. Press the Set Button Fagain to start the search for the next channel in that category.

Note that you may see a LOADING message, indicating that the XM tuner is downloading content and may not be able to operate. If the message continues to appear, check to see whether the XM antenna is properly positioned toward a south-facing window, experiment with the antenna position, or change to another input and then reselect XM Radio.

Recording

In normal operation, the audio or video source selected for listening through the AVR 445 is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for Tape Outputs £ or Video 1 Audio and Video Outputs Sg in the record mode. Remember that if your source is Dolby Digital or DTS, and you wish to make an analog recording, you must change

the REC OUT setting on the second page of the IN/OUT SETUP menu (Figure 3) to

DSP DWNMIX.

When a digital audio recorder is connected to the Digital Audio Outputs XY, you are able to record the digital signal using a CD-R, MiniDisc or other digi- tal recording system.

NOTES:

The digital outputs are active only when a digital sig- nal is present, and they do not convert an analog input to a digital signal, or change the format of the digital signal. In addition, the digital recorder must be compatible with the output signal. For example, the PCM digital input from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not.

The Front-Panel Video 4 N jacks may be config- ured for use as outputs, allowing connection to a recorder, when the steps shown in the section below are followed.

Please make certain that you are aware of any copyright restrictions on any material you copy. Unauthorized duplication of copyrighted materials is prohibited by federal law.

Front-Panel Connections

In addition to the rear-panel digital and analog outputs, the AVR 445 offers Harman Kardon’s exclusive config- urable front-panel output-jack feature. For easy con- nection of portable devices, you may switch the front- panel Video 4 Jacks N from an input to an output by changing the VIDEO 4 setting on the second page of the IN/OUT SETUP menu (Figure 3) from IN to OUT.

Once the setting is made, the Input/Output Status Indicator M will turn red, indicating that the jacks are now outputs, instead of the default setting as inputs. Once changed to an output, the setting will remain as long as the AVR 445 is turned on, unless the setting is changed in the OSD menu system. However, once the AVR 445 is turned off, the setting is canceled. When the unit is turned on again, the front-panel jacks will return to their normal default setting as inputs.

40 OPERATION

Image 40
Contents AVR AUDIO/VIDEO ReceiverAVR 445 AUDIO/VIDEO Receiver Modèle pour les CanadienDescription and Features IntroductionSafety Information Important Safety Information4Tuning Selector Volume Control FRONT-PANEL ControlsIs installed FRONT-PANEL ControlsFRONT-PANEL Controls REAR-PANEL Connections You wish to control CD Audio Inputs Connect these jacks toDVD Video Inputs Connect the composite or Main Remote Control Functions To program the proper codes for the products in your system Second press selects the device connected to the Hdmi 2 jackMain Remote Control Functions Main Remote Control Functions ZR 10 Remote Control Functions 16 ZR 10 Remote Control Functions Installation and Connections System InstallationAudio Equipment Connections Your areaSystem and Power Connections BUSInstallation Connections AC Power ConnectionsRS-232 Connections USB ConnectionsSystem Configuration System Setup Subwoofer Placement+ and polarity indicators that are Using the On-Screen DisplayIn/Out Setup Making Configuration AdjustmentsSetting the System Configuration Memory › Navigation Button DO U T S E T U P Audio Setup Surround SetupPœ to return to the main menu screen ‹/› Navigation Buttons D once so that 96kHz appears‹/› Navigation Buttons D to turn the mode on or OFF Three Dolby surround settings areThen press the Set Button pœ ScreenUsing EzSet/EQ System Configuration Manual Setup So that on is highlighted and then press the Set Button pœSpeaker Size Menu Speaker SizeLFE Low-Pass-Filter Setting To continue with overall configuration Sub Mode SettingFollowing options are available Subwoofer SizeDelay Adjust Setup menu Correct channelAdditional Input Adjustments Basic Operation OperationSource Selection Volume and Tone Control Surround Mode SelectionDigital Audio Playback Lower Display Line $. Next, useDolby Digital Selecting a Digital SourceTo the AVR PCM PlaybackSpeaker/Channel Indicators Night ModeAM/FM Tuner Operation Using TheBridgeTMXM Radio Operation Front-Panel Connections RecordingFor tuner operation have different functions with XM Radio Output Level Trim Adjustment Memory BackupEzSet/EQ On/Off Dim FunctionAdvanced Features If you wish to make other adjustments, press DMP/ TheBridgeTM Auto PowerMultiroom Setup InstallationMultiroom Operation Surround Channel Amplifier AssignmentMultiroom Operation Infrared Output SelectionPreprogrammed Code Entry Configuring the RemoteBottom line Learning Commands Automatic Code EntryLearning Codes for an Input Selector Learning Keys for an Entire Device RemoteChanging Devices Macro ProgrammingPower On VID 2/TV VID 3/Cable AVR Logic 7 h Erasing a MacroPunch-Through Configuration Volume Punch-ThroughMacro to be erased appears, press the Set Button F Read a MacroChannel Punch-Through Returning the Channel Control Settings to Default OperationTransport Punch-Through Renaming Renaming a DeviceAs shown in Figure CharactersResetting the Remote By pressing a particular buttonAt this point, you have two options To be reenteredAdditional Notes on Configuring and Operating the Remote Device Priority TimingBacklight Options To change the device priority timing, follow these stepsW B a T T E R Y Troubleshooting Guide Processor ResetSurround Mode Chart AppendixDefault Surround VideoTuner TapeSub Mode Channel AdjustVolume Default Volume Default SetFeature DVD AVR 445 Technical Specifications