Harman-Kardon HA160-0004-A manual Quick Start Connection and Setup

Signature 2.0

Quick Start Connection and Setup

Connect 75-ohm	Connect to coaxial	Connect to output	Connect to
FM antenna here	digital audio output	of composite	composite
	of A/V sources, DVD,	video sources	video input
	HDTV, CD, etc.		of VCRs

Connect AM loop	Connect to optical	Connect to	Connect to
antenna here	digital audio output	composite	S-Video
	of A/V sources, DVD,	video input of	output
	HDTV, CD, etc.	main monitor	sources

Connect to S-Video input of main monitor

Connect AC Power to non-switched wall outlet

Connect to S-Video input of VCRs

Quick Start

® FM AM

NRTL /C							1	2	3	4	5	6
LR110480
CSA E65			ANTENNA
									DIGITAL AUDIO DATA INPUTS
FRONT	CENTER	SURR	1	2	3	4	5	6		FRONT	CENTER	SURR
L												L
R												R
	SUB										SUB

6-CH DIRECT INPUTS ANALOG AUDIO INPUTS REC OUTPUTS AUDIO OUTPUTS

IN

1 2 3

4 5 6

COMPOSITE VIDEO

OUT

MAIN

REC

IN	OUT
1	MAIN
2	REC
S – VIDEO
RS-232
IR	IR
IN	OUT

EXTERNAL CONTROLS

TRIGGER OUTPUT

MODEL NO.: SIGNATURE SERIES 2.0

HARMAN KARDON

NORTHRIDGE

CALIFORNIA, USA

MADE IN USA

115V ~ 60Hz

75 WATTS

SERIAL NUMBER

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby", "AC-3", "Pro Logic" and the Double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, Inc. All rights reserved.

Instructions

Connect to analog audio	Connect to audio	Connect to	Connect to	Connect to "Trigger
output of A/V sources,	input of VCR or	a powered	inputs of audio	In" jack on Signature
CD, tuner, etc.	audio recorders	subwoofer	power amplifiers	Series or other compatible
		or subwoofer		power amplifier
		amplifier

1.Before proceeding, make certain that all equipment, including the 2.0, is unplugged from AC power. This will prevent any damage due to the unintended activation of automatic turn-on circuits.

2.Use high-quality audio and video interconnect cables to connect your source equipment to the rear of the 2.0 as shown in the diagram above and the table below. It is important to note that unlike conventional audio/video equipment, the 2.0 does not have inputs that are labeled for connection to a specific type of equipment (e.g., inputs labeled “CD,” “Tape” or “VCR”). Instead, the 2.0 allows you to connect the analog or digital audio and composite or S-Video outputs of your source equipment to any of the inputs. Then, using the setup procedures detailed on page 28 of this manual, you can custom configure the input sources. However, for a quick starting point, follow the input suggestions outlined in the chart shown below. They conform to the preset conditions for the 2.0.

Source	Remote	Video Input	Audio Input
Equipment	Button	Connection	Connection
Cable Box, Satellite	TV	Analog 2	Composite 2
Receiver, TV Tuner
VCR	Video 1	Analog 1	Composite 1
DVD	Video 2	Digital 1	S-Video 1
HDTV, Satellite with Digital	Video 3	Digital 2	S-Video 2
Audio, Laser Disc
Tuner (internal)	Tuner	(Internal Tuner)	Composite 2
CD Player	CD	Digital 3	N/A
Cassette or Tape Deck	Tape	Analog 5	N/A
Outboard Decoder	Aux	6-Ch. Direct Inputs	Composite 1

5