Harman-Kardon HA160-0004-A manual Quick Start Instructions

Page 10

Signature 2.0

Quick Start Instructions

NOTE: To use the sources when they are connected as shown in the chart on the previous page, press the button name shown. The button names may not correspond exactly to the type of source used for any input profile, but you may rename the input source for the on-screen display by following the instructions shown on page 27 of this manual.

3. Connect the video “Record Inputs” of your VCR to the Composite or S-Video “Rec” Outputs.

4.Connect the audio “Record Inputs” of your VCR and/or audio tape recorder to the “Rec” Outputs on the rear of the 2.0. There is no problem in sending the feed to both recorders and two recordings may be made at one time from the same source.

5.Connect the Composite or S-Video “Main” Outputs to the matching Composite or S-Video input on your TV monitor or projector.

6.Connect the AM and FM antennae supplied with the 2.0 to the proper antenna connections on the rear panel.

7.If a Signature Series audio power amplifier, or other compatible amplifier, is being used, connect the power trigger cable supplied with the 2.0 to the Trigger Output on the 2.0 and the amplifier’s compatible Trigger Input.

8.Connect the Audio Outputs of the 2.0 to the inputs of your five-channel power amplifier. Be certain that channels are properly matched (e.g., connect left to left, right to right, etc.) Connect the Sub Output to the mono “line level” input of a powered subwoofer, or to the audio input of the amplifier channel feeding a passive subwoofer. Connect the audio amplifier to the speakers, carefully following the instructions provided with the speaker and amplifier, and ensure that polarity is matched between the speaker and amplifier when connections are made.

9.Install the batteries in the remote control, being careful to observe the (+) and (–) polarity indicators on the remote and the batteries.

10.Connect all devices, including the 2.0, to AC

power and turn everything on EXCEPT for the 2.0 and any audio amplifier not connected to the 2.0’s triggered output.

11.Press the Master Power Switch on the 2.0 in until it latches and is flush with the front panel. A green standby LED will light, and the front panel Information Display will come on briefly to display the software version installed in your unit and then a Power Off Standby message will show briefly. The unit will then go into the Standby mode.

•To use the On-Screen Menu System, make certain that your TV or other video display device is turned on and switch to the proper video input at this point.

12.To turn the 2.0 on, press either the front panel Standby button, the Main On button on the remote, or any of the source buttons on the remote (e.g., TV, Vid 1, Tuner, etc.). The front panel Information Display will illuminate, the amber standby LED will go out and be replaced by blue illumination behind the word “Signature” on the front panel. A message will briefly appear in the on-screen display with the source, surround mode and volume.

•If you are using a Signature Series amplifier or another compatible amplifier connected to the Trigger Output jack, it will receive a turn-on signal as soon as the 2.0 is turned on. Note that with most amplifiers there will be a short, intentional delay between the turn-on signal and when the amplifier sends signals to the speakers. This is a normal function designed to prevent damage to your speakers.

•If you are using an amplifier not controlled by the 2.0’s Trigger Output, turn it on at least 10 seconds AFTER the 2.0 is turned on.

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HKSIG20 Page Signature 2.0 Processor/Tuner Staple or clip your original invoice here. Û Introduction Important Safety Information Typographic Conventions Unpacking and InstallationCleaning Moving The UnitEquipment Required for Quick-Start Installation Quick-Start InstructionsQuick Start Connection and Setup Quick StartQuick Start Instructions Operating Hints Front Panel Controls Standby LEDFront Panel Controls Rear Panel Connections ÞÝÜOptical Digital Audio Inputs Connect Remote Control Operation Volume VolumeMemorized Remote Control Operation Remote Control Operation Loading Batteries Remote Control ProgrammingRemote Control Range To change the batteriesProgrammable Keys TV, Vid 1, Vid 2, Vid 3, Tuner, CD, TapeResetting the Remote Memory Input Connections System InstallationAudio Inputs Video Inputs System and Accessory InputsOutput Connections Audio OutputsSystem Accessory Connections Record OutputsSpeaker Selection and Placement System ConfigurationSpeaker Placement Power Off Standby Configuring Your SystemSignature Series Ver Signature Series Power On Standby Speaker SetupTVVol Dolb y ProLo gic Figure OSD-3 Menu Control button i until Speaker DistancesSource Configuration Figure OSD-5Surround Mode Assignment Input AssignmentInput Level Adjust Video DetectSet Input Levels Input Level Ref Effects SetupInput Level EffectsBalance Balance 0 LF F/B 6 BAK Figure OSD-9Turn-On Volume Advanced SetupPower-Up State Standby When this option is selected, System Control and Unit IDDisplay Options Figure OSD-11Display Options Video Fmt Ntsc Figure FPD-7Operating the Signature Volume Control and MuteTurn On/Turn Off Volume Video Mute Dolby ProLogicTuner Vol Stereo Source Selection01 90.7 FM Vol Surround Mode Change DVDVol Dolb y D i g italDirect Access Controls Treble CutBass Boost Subwoofer TrimSurround Adjust Center Channel AdjustBalance Display Status Report Figure OSD-24Tuner Operation Tuner and Frequency Band SelectionDirect Access Tuning Manual TuningFM Tuning Mode Selection 02 89.9 FM . VolPreset Tuning ÐÐ 90.7 FM . Vol 011004 91.5 FM . Vol RDS TuningRDS Display 04 91.5 FM04 91.5 FM . Vol RDS ID RDS Program Type Search05 102.7 FM Search Tuner Menu Figure OSD-33Station Naming and Personal Preferences Figure OSD-36Recording Simulcast OperationInput Track Recording Selectable Recording Figure OSD-38System Reset Troubleshooting GuideError Messages Digital Noise With DVD PlayersMenu Control button Troubleshooting Chart Symptom Possible Cause SolutionAdvanced Settings Factory PresetsSources Speaker Setup TunerSoftware Version User WorksheetsSources Surround Mode Definitions Dolby Pro LogicDolby Digital Late Night Dolby DigitalDolby Digital Mono DTS Movie ModesStereo MonoMono + Program Type Program Type Name PTY Abbreviation RDS Data SystemTOP Top 40 Music Bass Boost Treble CutOutputs Signature 2.0 Processor/Tuner SpecificationsInputs Surround ModesTuner Section FM Signal-To-Noise RatioGeneral Description Subject Index Subject Index

HA160-0004-A specifications

The Harman-Kardon HA160-0004-A is a premium audio amplifier that epitomizes the brand's commitment to high-fidelity sound and innovative technology. This device is designed for audiophiles who demand exceptional performance and a rich listening experience, making it an excellent choice for both home theater systems and high-end audio setups.

One of the standout features of the HA160-0004-A is its power capability. The amplifier delivers an impressive output of 80 watts per channel, ensuring that even the most demanding speakers can perform efficiently without distortion. This power is complemented by a carefully designed Class AB amplification architecture, which combines the benefits of both Class A and Class B designs. The result is a warm, natural sound with a high level of detail across the audio spectrum.

The HA160-0004-A supports a wide range of audio formats and input options, making it versatile for any home audio system. It is equipped with multiple analog inputs, including RCA and balanced XLR inputs, allowing users to connect various audio sources seamlessly. Additionally, it includes digital audio inputs such as optical and coaxial, accommodating modern digital audio playback devices. Users can easily switch between sources using the intuitive front panel or remote control.

Harman-Kardon's commitment to sound quality is further exemplified by the use of high-quality components within the HA160-0004-A. The amplifier features advanced circuitry designed to minimize noise and distortion, which is crucial for preserving the integrity of the audio signal. This results in a clear and dynamic sound, whether listening to music, watching movies, or gaming.

Another noteworthy characteristic of the HA160-0004-A is its sleek, elegant design. The chassis is built with high-quality materials, showcasing a clean aesthetic that will complement any modern audio setup. The front panel features a user-friendly layout with an illuminated display, making it easy to monitor input selections and volume levels.

Additionally, the HA160-0004-A is engineered for durability and longevity, with robust construction that allows it to withstand regular use over time. This amplifier is not only a powerful audio device but also an appealing centerpiece for your entertainment space.

In conclusion, the Harman-Kardon HA160-0004-A amplifier represents a blend of performance, versatility, and style. With its powerful output, advanced technologies, and elegant design, it is well-suited for audiophiles and casual listeners alike, ensuring a superior audio experience across various applications.
Top Page Image Contents