Kenmore 625.38376 owner manual Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve

Page 11

ASSEMBLE INLET OUTLET ADAPTORS, OR SINGLE BYPASS VALVE

Complete the following steps to assemble the adaptors or bypass valve.

1.Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7.

2.Shut off the gas or electric supply to the water heater. See Fig. 7.

3.Open the highest and lowest water faucets in your

house. This will let water drain from the pipes. Close faucets after water has drained.

4.Remove the main cover. See Fig. 8. Pull outward on two (2) tabs to release.

The salt hole cover remains attached to the main cover

when removed. Set both covers aside so they will not get scratched or broken.

INSTALL SEARS BYPASS VALVE AND / OR THE INLET OUTLET THREADED ADAPTORS

NOTE: If you will not instafl the bypass valve because you will have a three (3) valve bypass, skip steps 6 & 7, but do steps 5 and 8.

5.Visually check and remove any foreign materials from the valve inlet and outlet ports. See Fig. 9. Carefully remove the two large plastic clips (you will use them). Check to be sure the turbine and turbine support are firmly in place. See Fig. 10.

BYPASS VALVE:

6.Put a light coating of silicone grease on the o-ring seals and slide onto the bypass valve.

7.Push the bypass valve into the softener valve as far as it will go. Snap the two large holding clips into place, from the top down as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the bypass valve will not puff out. See Fig. 11.

INLET AND OUTLET THREADED ADAPTORS:

8.Put a light coating of silicone grease on the o-ring seals and slide into the threaded adaptors. Push the adaptors into the valve inlet and outlet ports, or bypass valve ports, as far as they will go. Both adaptors are the same and fit either port. Snap the two large holding clips into place, as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so the tubes wifl not pull out. See Fig. 11.

Shutoff

Shutoff

.

Pressure

Valve

Valve

,z/

Tank

Pump

Electrical

Panel

FiG. 7

Salt Hole Cover

FIG. 8

INSTALLING BYPASS VALVE, AND/OR iNLET AND OUTLET THREADED ADAPTORS

Clip (2)

Valve Outlet

Included with

Softener

Valve Inlet_

_.

Included with

 

 

 

 

Softener

Questions? Call The Kenmore Water Line 1-800-426-9345

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Part No Rev. M 4/17/08 Save this ManualTEN Year Limited Warranty Against Leaks Warranty on Water SoftenerThree Year Limited Warranty on Electronic Parts Facts Figures To Keep Table of ContentsPage INSPECT Shipment Parts DescriptionsSmall Parts Pipe Proper Order to Install Water Treating EquipmentShu -offII Where to Install the Water SoftenerFittings Draw Your PipesPipe or both OUTDrain port Before iNSTALLiNG Checks & TestsInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Valve Bypass INSTALLiNG Holding ClipsBypass Valve Turned Downward Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing ConnectthevalvedrainhoseTo check for leaks, complete the following steps House Main Water Shutoff ValvesSingle Bypass Leak TestSoftener in and OUT Pipes InstallgroundingclampbetweenConnecting Transformer Electrical Power Outlet for Your SoftenerYour Plumbing Installation and Electrical InstallcoversHardness Number Presenttime SET Present TiME of DAYSET Water Hardness Number 2ppmironx5= Gpg hardness +10Tize it Sanitize Your Water Softener AS FollowsIt draws the bleach Into and through Softener To sani Water Softening Salt with Iron Removing Additives Unit plugged Into a continuously live outlet? CHECKLiST of STEP-BY-STEP Guides to INSTALLInstalled? Are the drain lines clamped and secured?Salt Monitor System ExtrarechargeRecharge NOW Recharge TonightMaximum Days Between Regen Erations Clean Feature Minutes 97% FeatureLO M Tank LightWater Flow Through the Softener COlProgram Memory Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureRegeneration Water Flow Through Softener in ServiceSoft Water Service and Regeneration Water Flow Through Softener in FillSoftener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Electronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener CleanNozzle & Venturi Protect the Water Softener from Freezing Drain ALL Water from SoftenerCorrection Checklistto Helpyou Save MoneyProblemcause Bypass Valves 37,900 @ 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19Flow Rate GPM 30,000 @Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstMost Likely Possible ProblemOther Information TroubleshootingTimer PWA Replacement MAX. Backwash Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Brine RinseTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyBrining and Brine Rinse Cycle Water Flow Through the Softener ValveFill Cycle Backwash Cycle Water Flow Through the SoftenerValve Backwash Cycle Fast Rinse CycleQuestions? Call The Kenrnore Water Line 1=800=426=9345 Part Water SoftenerComplete Part NumberGrounding Clamps Inlet OutletBrine Valve Assembly Wear-Strip Seal Cross-Section View Number KeyElectronics Call anytime For Repair Service CenterRepair Carry-in Items Vacuums Lawn Equipment For
Related manuals
Manual 48 pages 24.39 Kb Manual 48 pages 54.31 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents