Kenmore 625.38376 owner manual Wiring Schematic, Faceplate, Always Make These Initial Checks First

Page 35

WIRING SCHEMATIC

j

IACK

OF TIMER (PWA)

 

i

Transformer

'

 

L

tank light

 

 

 

 

 

 

valve motor

OUT

gm

Turbine

Sensor

NO

Position Switch

o NC

FACEPLATE

Keep this manual with your water softener. If repairs are needed, the service technician must have the informa- tion on the following pages.

ALWAYS MAKE THESE INITIAL CHECKS FIRST

1.Does the time display show the correct time of day?

•If display is blank, check power source to the sof- tener.

•If time is flashing, power was off for over 48 hours. The softener resumes normal operation but regen- erations occur at the wrong time.

•If an error code (Example: Err3) shows in the face-

plate display, go to AUTOMATIC ELECTRONIC DIAGNOSTICS.

2.Plumbing bypass valve(s) must be fully in service position.

3.The inlet and outlet pipes must connect to the

softener inlet and outlet respectively.

4.Is the transformer plugged into a "live" grounded wall outlet, and the power cable fastened secure= ly to the controller?

FIG. 59

5.The valve drain hose must be free of kinks and sharp bends, and not elevated over 8 ft. above the floor.

. Is there salt in the storage tank?

7.Is the brine tubing connected? Brine tubing con= nects to nozzle venturi and brine valve assembly.

. Is the brine valve float set right?

9.Press the SELECT1 button two times to display the hardness setting.

Be sure it is the correct setting for the household's water supply. (Make a hardness test of the raw water and compare with the hardness setting. Also test a soft water sample to verify if a problem exists.) Press the SELECT1 button twice more to return to present time in the display.

If you do not find the problem after making initial checks, do the MANUAL INITIATED ELECTRONIC DIAGNOSTICS, and the MANUAL ADVANCE REGEN-

ERATION CHECK.

Questions? Call The Kenmore Water Line 1-800-426-9345

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Part No Rev. M 4/17/08 Save this ManualTEN Year Limited Warranty Against Leaks Warranty on Water SoftenerThree Year Limited Warranty on Electronic Parts Facts Figures To Keep Table of ContentsPage INSPECT Shipment Parts DescriptionsSmall Parts Pipe Proper Order to Install Water Treating EquipmentShu -offII Where to Install the Water SoftenerFittings Draw Your PipesPipe or both OUTDrain port Before iNSTALLiNG Checks & TestsInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Valve Bypass INSTALLiNG Holding ClipsBypass Valve Turned Downward Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing ConnectthevalvedrainhoseTo check for leaks, complete the following steps House Main Water Shutoff ValvesSingle Bypass Leak TestSoftener in and OUT Pipes InstallgroundingclampbetweenConnecting Transformer Electrical Power Outlet for Your SoftenerYour Plumbing Installation and Electrical InstallcoversHardness Number Presenttime SET Present TiME of DAYSET Water Hardness Number 2ppmironx5= Gpg hardness +10Tize it Sanitize Your Water Softener AS FollowsIt draws the bleach Into and through Softener To sani Water Softening Salt with Iron Removing Additives Unit plugged Into a continuously live outlet? CHECKLiST of STEP-BY-STEP Guides to INSTALLInstalled? Are the drain lines clamped and secured?Salt Monitor System ExtrarechargeRecharge NOW Recharge TonightMaximum Days Between Regen Erations Clean Feature Minutes 97% FeatureLO M Tank LightWater Flow Through the Softener COlProgram Memory Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureRegeneration Water Flow Through Softener in ServiceSoft Water Service and Regeneration Water Flow Through Softener in FillSoftener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Electronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener CleanNozzle & Venturi Protect the Water Softener from Freezing Drain ALL Water from SoftenerCorrection Checklistto Helpyou Save MoneyProblemcause Bypass Valves 37,900 @ 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19Flow Rate GPM 30,000 @Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstMost Likely Possible ProblemOther Information TroubleshootingTimer PWA Replacement MAX. Backwash Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Brine RinseTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyBrining and Brine Rinse Cycle Water Flow Through the Softener ValveFill Cycle Backwash Cycle Water Flow Through the SoftenerValve Backwash Cycle Fast Rinse CycleQuestions? Call The Kenrnore Water Line 1=800=426=9345 Part Water SoftenerComplete Part NumberGrounding Clamps Inlet OutletBrine Valve Assembly Wear-Strip Seal Cross-Section View Number KeyElectronics Call anytime For Repair Service CenterRepair Carry-in Items Vacuums Lawn Equipment For
Related manuals
Manual 48 pages 24.39 Kb Manual 48 pages 54.31 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents