Kenmore 625.38376 owner manual House Main Water Shutoff Valves, Single Bypass, Leak Test

Page 15

LEAK TEST

To check for leaks, complete the following steps:

CAUTION: To avoid water or air pressure dam-

age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be

sure to do the following steps exactly asShu_ instructed.

HOUSE MAIN WATER

SHUTOFF VALVES

Sh t ff Vale --_:_= Pressure Tank

Meter

1.Fully open two cold, soft water faucets near the softener.

2.Look at the pictures in Fig. 18 and 19 to deter- mine your kind of bypass valve(s). Place bypass valve(s) in "bypass" position. On a single valve, slide the stem inward to bypass. On a three (3) valve system, close the inlet and outlet valves and open the bypass valve.

3.Fully open the house main water pipe shutoff

valve. Observe steady water flow from both open faucets.

4.Place bypass valve(s) in SERVICE EXACTLY as follows: Keep soft water faucets open.

a. Single Bypass Valve: Slowly, slide pull the valve stem outward toward service, pausing sev= oral times to allow the softener to pressurize slow- ly.

b. Three Valve Bypass: Fully close the bypass valve and open the outlet valve. Slowly, open the inlet valve, pausing several times to allow the sof- tener to pressurize slowly.

5.After about three minutes, open a hot water faucet for about one minute, or until all air is expelled, then close.

6.Close both cold water faucets.

7.Check your plumbing work for leaks and fix right

away if any are found. Be sure to observe previ- ous caution notes.

NOTE: If this procedure is performed on a new softener, water coming from the taps may initial- ly be discolored. This normally occurs the first time water runs through the resin bed. The dis- colored water is not harmful, and the discol- oration will not last more than a few minutes.

FOR SERVICE

Close bypass valve. Open inlet & outlet valves.

FOR BYPASS

Open bypass valve. Close inlet & outlet valves.

Water

Well Pump

FIG. 17

SINGLE BYPASS

Pull Stem Outward

For Service

Push Inward

For Bypass

Note: Stem may be installed in either direction. The end

with writing should be pulled out for service position.

FIG. 18

VALVE BYPASS

Valve

Outlet

ValveInlet

Valve

FIG. 19

Questions? Call The Kenmore Water Line 1-800-426-9345

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Part No Rev. M 4/17/08 Save this ManualWarranty on Water Softener Three Year Limited Warranty on Electronic PartsTEN Year Limited Warranty Against Leaks Facts Figures To Keep Table of ContentsPage Parts Descriptions Small PartsINSPECT Shipment Pipe Proper Order to Install Water Treating EquipmentShu -offII Where to Install the Water SoftenerFittings Draw Your PipesPipe or both OUTDrain port Before iNSTALLiNG Checks & TestsAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors INSTALLiNG Holding Clips Bypass Valve Turned DownwardValve Bypass Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing ConnectthevalvedrainhoseTo check for leaks, complete the following steps House Main Water Shutoff ValvesSingle Bypass Leak TestSoftener in and OUT Pipes InstallgroundingclampbetweenConnecting Transformer Electrical Power Outlet for Your SoftenerYour Plumbing Installation and Electrical InstallcoversHardness Number Presenttime SET Present TiME of DAYSET Water Hardness Number 2ppmironx5= Gpg hardness +10Sanitize Your Water Softener AS Follows It draws the bleach Into and through Softener To saniTize it Water Softening Salt with Iron Removing Additives Unit plugged Into a continuously live outlet? CHECKLiST of STEP-BY-STEP Guides to INSTALLInstalled? Are the drain lines clamped and secured?Salt Monitor System ExtrarechargeRecharge NOW Recharge TonightMaximum Days Between Regen Erations Clean Feature Minutes 97% FeatureLO M Tank LightWater Flow Through the Softener COlProgram Memory Recharge Time Remaining and Valve Position IndicatorsError Code Kenmores Ultra Cleansing FeatureRegeneration Water Flow Through Softener in ServiceSoft Water Service and Regeneration Water Flow Through Softener in FillWater Flow Through Softener Brining and Brine Rinse Water Flow ThroughSoftener in Backwash Soft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeKeeping the Water Softener Clean Nozzle & VenturiIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerChecklistto Helpyou Save Money ProblemcauseCorrection Bypass Valves 37,900 @ 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19Flow Rate GPM 30,000 @Eration Check Wiring SchematicFaceplate Always Make These Initial Checks FirstMost Likely Possible ProblemTroubleshooting Timer PWA ReplacementOther Information MAX. Backwash Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN Brine RinseTo Relieve Pressure RotaryvalveserviceDisassembly AssemblyWater Flow Through the Softener Valve Fill CycleBrining and Brine Rinse Cycle Backwash Cycle Water Flow Through the SoftenerValve Backwash Cycle Fast Rinse CycleQuestions? Call The Kenrnore Water Line 1=800=426=9345 Part Water SoftenerComplete Part NumberGrounding Clamps Inlet OutletBrine Valve Assembly Wear-Strip Seal Cross-Section View Number KeyElectronics Call anytime For Repair Service CenterRepair Carry-in Items Vacuums Lawn Equipment For
Related manuals
Manual 48 pages 24.39 Kb Manual 48 pages 54.31 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents