Kenmore 625.38376 owner manual Troubleshooting, Other Information, Timer PWA Replacement

Page 37

TROUBLESHOOTING

VALVE POSiTiON iNDiCATORS:

Depending on the valve position, the following indica- tors show in the display:

indicator

Valve

Position

Serv

Service

Fill

Fill

 

Brine

Brining/Brine Rinse

Bkwsh

Backwash

Rinse

Fast

Rinse

When the valve is rotating from one cycle to another, both indicators flash. For example, if the valve is in transition between fill and brining, both Fill and Brine flash. Upon reaching brining position, Fill goes off and Brine is on steady. The time display shows the minutes of the cycle remaining.

NOTE: If the faceplate is left in a diagnostic display (or a flashing display when setting times or hard-

hess), present time automatically returns if a button is not pressed within 4 minutes. To return to the diagnostic display, repeat step 1.

OTHER INFORMATION

While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is retained by the computer from the first time electrical power is applied to the faceplate.

•Press and hold the UP button to display the number of days this faceplate has had electrical power applied.

•Press and hold the DOWN button to display the num- ber of regenerations initiated by this faceplate since the code number was entered.

•Press the RECHARGE button to advance the valve to each position and observe the switch and position indicators to verify component operation, or to possi- bly isolate a defect.

•Press and hold the SELECT1 button for 3 seconds until a model code shows in the display, see Fig. 64.

This code identifies the softener nominal capacity size. If the wrong number shows, the softener will operate on incorrect data. Do the following as needed.

If the correct model code (H 32) shows: Press the SELECT1 button to return to the present time display.

To change the number: Press the UP or DOWN but- ton until the correct model code (H 32) shows. Then, press the SELECT1 button and reset the timer.

'_ Motor

Housing

Position Switch

Turbine

Turbine

Support

and Shaft

Valve Outlet

FiG. 62

Position markers (Valve in service)

FiG. 63

TIMER PWA REPLACEMENT

Be sure the valve is in service position when replac= ing the timer PWA (observe valve cycle indicator). If after installing and programming the replacement timer PWA, the valve is not in service position, do the following to assure correct cycle orientation, or timing, between the faceplate and valve.

Use the MANUAL ADVANCE procedures with the RECHARGE NOW button, advance through the recharge cycles until the valve stops in service position, and RECHARGE no longer flashes in the display.

NOTE: The valve motor may automatically drive through several valve positions while searching for service. If an error code occurs, unplug the trans- former, then plug in again.

,,

FiG. 64

Questions? Call The Kenmore Water Line 1-800-426-9345

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Part No Rev. M 4/17/08 Save this ManualThree Year Limited Warranty on Electronic Parts Warranty on Water SoftenerTEN Year Limited Warranty Against Leaks Facts Figures To Keep Table of ContentsPage Small Parts Parts DescriptionsINSPECT Shipment Pipe Proper Order to Install Water Treating EquipmentShu -offII Where to Install the Water SoftenerFittings Draw Your PipesPipe or both OUTDrain port Before iNSTALLiNG Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Bypass Valve Turned Downward INSTALLiNG Holding ClipsValve Bypass Typical Soldering Connections Move Softener Into PlacePosition Softener Into Place Connect the SoftenerConnect Salt Tank Overflow Tubing ConnectthevalvedrainhoseSingle Bypass House Main Water Shutoff ValvesLeak Test To check for leaks, complete the following stepsConnecting Transformer InstallgroundingclampbetweenElectrical Power Outlet for Your Softener Softener in and OUT PipesYour Plumbing Installation and Electrical InstallcoversSET Water Hardness Number SET Present TiME of DAY2ppmironx5= Gpg hardness +10 Hardness Number PresenttimeIt draws the bleach Into and through Softener To sani Sanitize Your Water Softener AS FollowsTize it Water Softening Salt with Iron Removing Additives Installed? CHECKLiST of STEP-BY-STEP Guides to INSTALLAre the drain lines clamped and secured? Unit plugged Into a continuously live outlet?Recharge NOW ExtrarechargeRecharge Tonight Salt Monitor SystemMaximum Days Between Regen Erations Clean Feature Minutes 97% FeatureWater Flow Through the Softener Tank LightCOl LO MError Code Recharge Time Remaining and Valve Position IndicatorsKenmores Ultra Cleansing Feature Program MemorySoft Water Service and Regeneration Water Flow Through Softener in ServiceWater Flow Through Softener in Fill RegenerationWater Flow Through Water Flow Through Softener Brining and Brine RinseSoftener in Backwash Water Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeNozzle & Venturi Keeping the Water Softener CleanIron from Resin BED Protect the Water Softener from Freezing Drain ALL Water from SoftenerProblemcause Checklistto Helpyou Save MoneyCorrection Bypass Valves Flow Rate GPM 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1930,000 @ 37,900 @Faceplate Wiring SchematicAlways Make These Initial Checks First Eration CheckMost Likely Possible ProblemTimer PWA Replacement TroubleshootingOther Information Cycle Flow Rates Gallons PER MIN Manual Advance Regeneration CheckBrine Rinse MAX. BackwashDisassembly RotaryvalveserviceAssembly To Relieve PressureFill Cycle Water Flow Through the Softener ValveBrining and Brine Rinse Cycle Valve Backwash Cycle Water Flow Through the SoftenerFast Rinse Cycle Backwash CycleQuestions? Call The Kenrnore Water Line 1=800=426=9345 Complete Water SoftenerPart Number PartGrounding Clamps Inlet OutletBrine Valve Assembly Wear-Strip Seal Cross-Section View Number KeyRepair Carry-in Items Repair Service CenterVacuums Lawn Equipment For Electronics Call anytime For
Related manuals
Manual 48 pages 24.39 Kb Manual 48 pages 54.31 Kb

625.38376 specifications

The Kenmore 625.38376 is a versatile and efficient air purifier designed to enhance indoor air quality in various environments, including homes, offices, and other spaces. This model is particularly recognized for its impressive filtration capabilities and user-friendly features, making it a popular choice among consumers seeking cleaner air.

One of the standout features of the Kenmore 625.38376 is its advanced three-stage filtration system. This system includes a pre-filter, a true HEPA filter, and an activated carbon filter. The pre-filter captures larger particles such as dust and pet hair, which helps to extend the life of the HEPA filter. The true HEPA filter is capable of trapping 99.97% of particles as small as 0.3 microns, effectively removing allergens like pollen, smoke, and mold spores from the air. The activated carbon filter further enhances the unit's performance by absorbing odors and volatile organic compounds (VOCs), contributing to a fresher indoor environment.

In addition to its powerful filtration system, the Kenmore 625.38376 includes several user-friendly technologies and features. The air purifier is equipped with a smart air quality sensor that continuously monitors the air quality in real-time. This sensor automatically adjusts the fan speed based on the pollution levels detected, ensuring optimal cleaning performance without unnecessary energy consumption. Users can easily track air quality levels through an intuitive digital display that shows the current status.

Another significant characteristic of the Kenmore 625.38376 is its quiet operation. The unit is designed to operate at low noise levels, making it suitable for use in bedrooms and other quiet spaces. It features multiple fan speeds, allowing users to adjust the airflow according to their specific preferences and needs.

The Kenmore 625.38376 is also energy efficient, certified by ENERGY STAR. This certification assures consumers that the unit meets stringent energy efficiency guidelines, promoting lower electricity bills and a reduced environmental impact.

In summary, the Kenmore 625.38376 air purifier combines advanced filtration technologies, smart sensors, quiet operation, and energy efficiency to create a reliable solution for improved indoor air quality. Its thoughtful design and effective performance make it an excellent choice for individuals looking to breathe cleaner air in their homes.
Top Page Image Contents