Kenmore 625.34867 2A.FACEPLATE Timer Features, HOW Your Water Softener Works, Extra Recharge

Page 10

SECTION 2

HOW YOUR WATER SOFTENER WORKS

I

2A.FACEPLATE TIMER FEATURES

EXTRA RECHARGE

Sometimes, a manually started regeneration (re- charge) may be desired, or needed• Two examples are:

--You have used more water than usual (guests visiting) and you may run out of soft water before the next timer started regeneration.

--You did not refill the softener with salt before it was gone.

You can start a regeneration right away, or you can set the timer to regenerate at the next 2:00 AM (or other preset recharge time). Do the following•

RECHARGE NOW

button and bold until RE-I'',"I

• ?_IE

CHARGE, SERV and FILL begin ] _ ]

to flash in the display. Upon] ' ]

• Press the ON/OFF-HOLD]#,_=,,,_I,,_ 2QB'I 1 reaching fill, the first cycle of re- _, ]

generation, the flash ng SERW ....

goes off and FILLis on steady. RECHARGE contin- ues to flash. This regeneration will last for about

2-112 to 2-3/4 hours. After this time, you will have soft water again.

"NOTE:

If the CLEAN feature is set to ON, a cleaning backwash

precedes the recharge. CLEAN and Bkwsh or Rinse flashes in the display, along with the minutes of the clean cycle remaining.

SALT MONITOR SYSTEM

The faceplate timer has a low salt monitor with an indicator light to remind you to refill the storage tank with salt. To set this monitor system:

1.Lift the salt hole cover and level the salt in the storage tank (press tank light button to light inside of tank).

o The salt level decal, on the brinewell inside the tank, has numbers from 0 to 8 (see drawing on

page 9 and below)• Observe the number the leveled salt is at or closest to.

3.Now, press the SALT LEVEL ADJUST button until black bars display up to the salt level number. For example, the pictures below show the salt level at 6.

4.Hnally, set the level you want the low salt indicator light to come on. Press the SIGNAL LIGHT ADJUST button until a (÷) shows opposite this number. In the example below, the light will come on when the stored salt drops to level 2. At level 2, the storage tank is about 1/3 full. This is the lowest you should allow the stored salt level to drop to. To

turn the salt monitor off, press the button until OFF shows.

bdnewell

indicator ligb

/LOWSAG

RECHARGE TONIGHT

hold) the ON/OFF-HOLD but- """

-]'_8_'

ton. RECHARGE TONIGHT

flashes in the display, and the

• Press and release (do not []I_'7'' softener begins regeneration at .2'..

the next preset recharge time.

Press and release the ON/OFF-HOLD button once

more if you decide to cancel the regeneration, and

RECHARGE TONIGHT.

bats level

saltZ level

NOTE:

For accurate salt monitor operation, always use nugget or pellet water softener salt. See page 9. If potassium chloride is used, be sure to adjust the timer to the KCl setting on page 7.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model no Save this ManualFull TEN Year Warranty Against Leaks WarrantyFull Three Year Electronics Warranty Repair Parts Care of Your SoftenerSafety Guides SectionCheck List of ALL STEP-BY-STEP Guides to Install SectionSET Present Time of DAY Program the TimerWater Softener START-UP SET Water Hardness NumberSET Clean Feature Option Water Softener START-UP 1C.PROGRAM the TimerSET Recharge Regeneration Time Sanitizing the Water Softener ADD WaterADD Salt Fill the Storage Tank with SaltWater Softening Salt with Iron Remov Extra Recharge 2A.FACEPLATE Timer FeaturesHOW Your Water Softener Works Salt Monitor SystemOptional Adjustable Settings Ow YOURWATERSOFTE.ERWORKSHOW Your Water Softener Works Faceplate Timer Features Water Flow Through Softener in Fill 2B. Soft Water Service and RegenerationWater Flow Through Softener in Service Fill Backwash Brining Fast Rinse Brine RinseWater Flow Through Softener in Brining Brine Rinse 2B. Soft Water Service and RegenerationWater Flow Through Softener in Fast Rinse Automatic Bypass ElectronicsCareof Yoursoftener Salt BridgeKeeping the Water Softener Clean Iron from the Resin BEDFrom Freezing 3C. Keep the SoftenerCare of Your Softener 3D.HELPFUL Hints Checklist To Help YOU Save Money Problem Cause Correction4A.DIMENSIONS/SPECIFICATIONS Timer HF CodeWiring Schematic 5A.TROUBLESHOOTINGService Tech Information FaceplateManual Initiated Electronics DIAG- Nostics Service TECH. Information 5A.TROUBLESHOOTINGAutomatic Electronic Diagnostics Possible Defect CodeTroubleshooting Indicator Valve PositionManual Advance Regeneration Check Assembly 5B.ROTARY Valve ServiceDisassembly Servicing the Valve5C .. Water Flow Through the Softener Valve Service TECH. InformationService Cycle Fill Cycle5C. Water Flow Through the Softener Valve Brining and Brine Rinse Cycles\ \ 5C. Water Flow Through the Softener ValveSection Kenmore Water SOFTENER, Model no KEY Part Description NumberBrineassemblyvalve Inlet Outlet Grounding Clamps=P,,,IRPARTS Parts List KEY Part NO. NumberPage Page Sears

625.34867 specifications

The Kenmore 625.34867 is a compact, high-efficiency dehumidifier designed to improve indoor air quality in homes and small spaces. This versatile appliance proves to be a valuable addition for those struggling with excess moisture, mold, and mildew, particularly in areas such as basements, bathrooms, and laundry rooms.

One of the standout features of the Kenmore 625.34867 is its robust moisture removal capacity, which is capable of extracting up to 50 pints of water from the air each day. This makes it an ideal choice for medium to large-sized rooms, ensuring a comfortable atmosphere while effectively preventing the detrimental effects of humidity.

Equipped with a user-friendly digital control panel, the Kenmore 625.34867 allows for effortless operation and monitoring. Users can easily adjust the desired humidity level, which can be set between 35% and 85%, to suit their preferences. Additionally, the dehumidifier features a 24-hour timer and multiple fan speeds, offering flexibility in its operation to match varying conditions throughout the day.

One noteworthy technology integrated into this model is the built-in humidistat. This smart feature continuously monitors the room's humidity levels, automatically turning the unit on or off to maintain the set humidity, thereby conserving energy and ensuring optimal performance.

The Kenmore 625.34867 is also designed with optimal drainage solutions in mind. It includes a removable water tank with a large capacity, which makes emptying infrequent and straightforward. For added convenience, users can opt for continuous drainage via a standard garden hose, eliminating the need to manually empty the tank.

In terms of portability, this dehumidifier is equipped with durable caster wheels that allow for easy movement from room to room. The ergonomic top handle contributes to its ease of transport, making it simple to adapt it to different spaces as needed.

Finally, the Kenmore 625.34867 is designed with safety in mind. It features an automatic shut-off function that activates when the water tank is full, preventing overflow and potential water damage. Combined with its energy-efficient operation, this dehumidifier stands as a practical solution for maintaining a healthy indoor environment, free from excessive moisture and its associated issues.
Top Page Image Contents