SECTION 1
WATER SOFTENER START-UP
1C.PROGRAM THE TIMER
•Press the [_ UP/DOWN [] buttons to set your water hardness number in the display. The DOWN button moves the display to 1. The UP button moves the display to the highest setOng (see maximum setting for your model in the specifications).
NOTE:
If your water supply contains iron, compensate for it by adding to the water hardness number. Forexarnple, assume your water is 15 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each I ppm of
iron. In this example, 3_9u would use 25 for your hardness number
15 gpg hardness
2ppmironx5=10+10
(times) 25 HARDNESS NUMBER
4.SET CLEAN FEATURE OPTION:
•Press the SELECT button to display OFF
(flashing) | and | CLEAA_ |
|
| mr |
| OFF | |||||
This feature | is beneficial | on |
| water | ..... | |||||||
|
| ? |
|
| ||||||||
supplies | containing | iron | and/or |
| 6 |
| _ | |||||
| 5 |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
| |
high amounts of sediments (sand, |
| ii |
|
| ||||||||
| 3 |
|
| |||||||||
silt, dirt, etc.). When set to ON, a |
| 2 |
|
| ||||||||
. | T_ |
|
| |||||||||
backwash and fast rinse cycle will |
|
|
|
| ||||||||
occur | first, | preceeding | the | nor- | - | ON | ||||||
mal | regeneration | sequence |
| (see |
| 7 |
|
| ||||
|
| 6 |
| _.F.AH | ||||||||
page 13). This provides extra |
| 5 |
|
| ||||||||
| 4 |
|
| |||||||||
cleaning | of the resin | bed | before it |
| 3 |
|
| |||||
| I |
|
| |||||||||
|
|
|
|
|
|
|
|
|
| 2 |
|
|
is regenerated | with | the salt |
| brine. |
| "" | " |
| ||||
To conserve | water, | if | your | water | supply does not | |||||||
contain | iron or sediments, |
| be sure | this feature is set to | ||||||||
OFF. Use | the | UP | / DOWN | buttons | to | change | the ON / |
OFF displays.
NOTE:
Each press of the UP/DOWN button changes the
display by 1 between 1 and 25. Between 25 and the highest number, the display changes 5 at a time...25,
30, 35, etc. Holding the UP or DOWN button in changes the display twice each second.
3. SET RECHARGE (REGENERATION) TIME:
•Press the #1 SELECT button to display 2:00 AM (flashing) and RECHARGE TIME.
At the 2:00 AM RECHARGE TIME _ _.'_., _,.N.0 _,[I setting, the softener begins regen-
eration (see pages 13 and 14) at I ,0 I 2:00 AM, ending about 4:30 AM. [ i
This is a good time in most I..'..I
households because water is not being used (see
AUTOMATIC BYPASS, page 15). If a different RECHARGE TIME setting would be better for your
household, do the following.
• Press the [_ UP/DOWN [] buttons to set the
desired RECHARGE starting hour. Be sure to observe the
NOTE:
Each press of the UP/DOWN buttons changes the
display 1 hour. Holding the buttons in changes the display twice each second.
5.SET SALT TYPE (sodium chloride or potas- sium chloride, see page 9):
• Press the SELECT button to display nACl, the default setting.
If you will use potassium chloride (KCI) instead of standard sodium chloride (NaCl) water softener salt, be sure to set KCI in the display using the UP button.
The KCl setting adjusts regeneration cycle times to
compensate for the variable dissolving rate of potassium chloride.
_zt
Ii.%___ nflE I_t te_tkEI
4 S
.°.
•Press the #1 SELECT button once again, to return
the present time, and RECHARGE TONIGHT in the
display.
vtr
"$'m9:39--
5
4
3
If you need help programming the timer, call toll flee, number
See pages 1O, 11 and 12for otber face plate timer features.
7