Kenmore 625.34867 owner manual Troubleshooting, Indicator Valve Position

Page 23

SECTION 5

SERVICE TECH INFORMATION

 

 

5A.

 

TROUBLESHOOTING

should

get a

reading

in the

display.

If you

get a

3. Press the #1 SELECT button and hold 3 seconds

reading,

unhook

the

in and out

plumbing

and

check

until...

the turbine for binding.

...SFaashows.

H; 2

 

o-"

MOTOR

 

 

 

POSITION SWITCH

SENSOR HOUSING

TURBINE

This code identifies the softener nominal capacity size. If the wrong number shows, the softener will operate

on incorrect programming. Do the following as needed.

TURBINE

SHAFT

VALVE

VALVE POSITION INDICATORS: Depending on the

valve position, the following indicators show in the display:

INDICATOR

VALVE

POSITION

Serv

service

Fill

fill

 

Brine

brining/brine rinse

Bkwash

backwash

Rinse

fast

rinse

When the valve is rotating from 1 cycle to another, both indicators flash. For example, if the valve is in transition between fill and brining, both Fill and Brine flash. Upon reaching brining position, Fill goes off and Brine is on steady. The time display shows the minutes of the cycle remaining.

NOTE: If the face plate is left in a diagnostic display

(or a flashing display when setting times or] hardness), present time automatically returns if a button is not pressed within 4 minutes. To return to

the diagnositc display, repeat step 2.

OTHER INFORMATION. While in this diagnostic screen, the following information is available and may be beneficial for various masons. This information is retained by the computer from the first time electrical power is applied to the face plate.

...Press [] to display the number of days this face plate has3_ad electrical Power applied.

...Press [_ to display the number of regenerations initiated by this face plate since the HF code number was entered.

HF32 does show -- Press the #1 SELECT button to return the present time display.

To

change

 

HF

number

-

Press

the

[]

or

[]

button

until

HF32

shows.

Then,

press

the

#1

SELECT button and reset the timer...page 6.

 

 

FACE PLATE REPLACEMENT: Be sure the valve

 

is

in

service

position

 

(observe

valve cycle

 

indicator)

 

when

replacing

the face

plate.

 

If, after installing

and

programming

the

replace-

 

ment

face

place,

the valve

_

in

service

posi-

 

tion, do the following to assure correct cycle

 

orientation,

 

or

timing,

between the face plate

 

and

valve.

 

 

 

 

 

 

 

 

 

 

Use

the MANUAL ADVANCE

procedures,

page

 

24.With the RECHARGE NOW button, advance through the recharge cycles until the valve stops

in service position, and RECHARGE no longer flashes in the timer.

NOTE: The valve motor may automatically drive through several valve positions while searching for service. If an error code occurs, unplug the transformer, then plug in again.

11"10NI

markers

(valve in service)

CAM

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Save this Manual Model noFull Three Year Electronics Warranty WarrantyFull TEN Year Warranty Against Leaks Care of Your Softener Repair PartsSection Safety GuidesSection Check List of ALL STEP-BY-STEP Guides to InstallSET Water Hardness Number Program the TimerWater Softener START-UP SET Present Time of DAYSET Recharge Regeneration Time Water Softener START-UP 1C.PROGRAM the TimerSET Clean Feature Option ADD Water Sanitizing the Water SoftenerWater Softening Salt with Iron Remov Fill the Storage Tank with SaltADD Salt Salt Monitor System 2A.FACEPLATE Timer FeaturesHOW Your Water Softener Works Extra RechargeOw YOURWATERSOFTE.ERWORKS Optional Adjustable SettingsHOW Your Water Softener Works Faceplate Timer Features Fill Backwash Brining Fast Rinse Brine Rinse 2B. Soft Water Service and RegenerationWater Flow Through Softener in Service Water Flow Through Softener in FillWater Flow Through Softener in Fast Rinse 2B. Soft Water Service and RegenerationWater Flow Through Softener in Brining Brine Rinse Electronics Automatic BypassSalt Bridge Careof YoursoftenerIron from the Resin BED Keeping the Water Softener CleanCare of Your Softener 3C. Keep the SoftenerFrom Freezing Problem Cause Correction 3D.HELPFUL Hints Checklist To Help YOU Save MoneyTimer HF Code 4A.DIMENSIONS/SPECIFICATIONSFaceplate 5A.TROUBLESHOOTINGService Tech Information Wiring SchematicPossible Defect Code Service TECH. Information 5A.TROUBLESHOOTINGAutomatic Electronic Diagnostics Manual Initiated Electronics DIAG- NosticsIndicator Valve Position TroubleshootingManual Advance Regeneration Check Servicing the Valve 5B.ROTARY Valve ServiceDisassembly AssemblyFill Cycle Service TECH. InformationService Cycle 5C .. Water Flow Through the Softener ValveBrining and Brine Rinse Cycles 5C. Water Flow Through the Softener Valve5C. Water Flow Through the Softener Valve \ \Section KEY Part Description Number Kenmore Water SOFTENER, Model noInlet Outlet Grounding Clamps Brineassemblyvalve=P,,,IRPARTS KEY Part NO. Number Parts ListPage Page Sears

625.34867 specifications

The Kenmore 625.34867 is a compact, high-efficiency dehumidifier designed to improve indoor air quality in homes and small spaces. This versatile appliance proves to be a valuable addition for those struggling with excess moisture, mold, and mildew, particularly in areas such as basements, bathrooms, and laundry rooms.

One of the standout features of the Kenmore 625.34867 is its robust moisture removal capacity, which is capable of extracting up to 50 pints of water from the air each day. This makes it an ideal choice for medium to large-sized rooms, ensuring a comfortable atmosphere while effectively preventing the detrimental effects of humidity.

Equipped with a user-friendly digital control panel, the Kenmore 625.34867 allows for effortless operation and monitoring. Users can easily adjust the desired humidity level, which can be set between 35% and 85%, to suit their preferences. Additionally, the dehumidifier features a 24-hour timer and multiple fan speeds, offering flexibility in its operation to match varying conditions throughout the day.

One noteworthy technology integrated into this model is the built-in humidistat. This smart feature continuously monitors the room's humidity levels, automatically turning the unit on or off to maintain the set humidity, thereby conserving energy and ensuring optimal performance.

The Kenmore 625.34867 is also designed with optimal drainage solutions in mind. It includes a removable water tank with a large capacity, which makes emptying infrequent and straightforward. For added convenience, users can opt for continuous drainage via a standard garden hose, eliminating the need to manually empty the tank.

In terms of portability, this dehumidifier is equipped with durable caster wheels that allow for easy movement from room to room. The ergonomic top handle contributes to its ease of transport, making it simple to adapt it to different spaces as needed.

Finally, the Kenmore 625.34867 is designed with safety in mind. It features an automatic shut-off function that activates when the water tank is full, preventing overflow and potential water damage. Combined with its energy-efficient operation, this dehumidifier stands as a practical solution for maintaining a healthy indoor environment, free from excessive moisture and its associated issues.
Top Page Image Contents