Kenmore 625.34867 owner manual 5B.ROTARY Valve Service, Disassembly, Servicing the Valve, Assembly

Page 25

SECTION 5

SERVICE TECH INFORMATION

5B.ROTARY VALVE SERVICE

Before working on the valve, turn off the water

supply and disconnect from electrical power. TO

RELIEVE PRESSURE:

--3 VALVE BYPASS: Close the inlet valve and open a soft water faucet. Then close the outlet valve and open the bypass valve.

--SEARS SPECIAL BYPASS: Slide the bypass valve stem to bypass position. Loosen 3 hex head screws toward the back side of the valve to allow pressure

water to bleed out.Catch water with a rag.

assembled

view

flow plug assembly

DISASSEMBLY

To remove a part or group of parts, refer to the valve drawing. A common screwdriver or nut driver, Phillips screwdriver and pliers are the only tools needed to completely disassemble.

SERVICING THE VALVE

Inspect all o-rings, seals and gaskets for wear or defects.

Inspect the bottom surface of the rotor for scratches, chips or wear.

NOTE: If replacement is needed, be sure to use the current replacement part.

ASSEMBLY

o-ring seals -_.

wavewasher-..._(_ beanng,wave washer---..-h._

wear-strip

rotor

o-nug seal

seal-

rotor seal

drainseal

, nozzle & ventunseal

sensor housing

Be sure all parts are in place and in the proper position. Lubricate ALL o-rings and seals with FDA

Sea

turbine suppod turbine

approved silicone grease. To install the rotor seal, first

place the seal into the valve groove, rounded side

down (see cross-section). Apply a light coating of

silicone grease to the seal's crossing ribs. Then,

carefully center the wear strip on the seal, and push it

downward onto the seal.

Nozzle assembly service, page 17

Install the nozzle and venturi seal and drain seal. Assemble wave washer bearing, the wave washer, and 2 o-rings onto the rotor top shaft. Then center the rotor in the valve body, on the rotor seal.

Lower the cover onto the valve body and rotor shaft.

Then install the cover holding screws. Before

tightening the screws, install the valve cam and

gear. Then, turn the rotor (clockwise only) to service

position. Tighten the screws using a criss-cross pattern. If a torque wrench is available, torque to 30-40 inch pounds.

Lubricate the gear on the motor, and the valve cam

gear with Molykote grease, or other high quality gear lubricant.

Be sure to orient switch as shown, with lever toward the cam.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Save this Manual Model noFull TEN Year Warranty Against Leaks WarrantyFull Three Year Electronics Warranty Care of Your Softener Repair PartsSection Safety GuidesSection Check List of ALL STEP-BY-STEP Guides to InstallWater Softener START-UP Program the TimerSET Present Time of DAY SET Water Hardness NumberSET Clean Feature Option Water Softener START-UP 1C.PROGRAM the TimerSET Recharge Regeneration Time ADD Water Sanitizing the Water SoftenerADD Salt Fill the Storage Tank with SaltWater Softening Salt with Iron Remov HOW Your Water Softener Works 2A.FACEPLATE Timer FeaturesExtra Recharge Salt Monitor SystemOw YOURWATERSOFTE.ERWORKS Optional Adjustable SettingsHOW Your Water Softener Works Faceplate Timer Features Water Flow Through Softener in Service 2B. Soft Water Service and RegenerationWater Flow Through Softener in Fill Fill Backwash Brining Fast Rinse Brine RinseWater Flow Through Softener in Brining Brine Rinse 2B. Soft Water Service and RegenerationWater Flow Through Softener in Fast Rinse Electronics Automatic BypassSalt Bridge Careof YoursoftenerIron from the Resin BED Keeping the Water Softener CleanFrom Freezing 3C. Keep the SoftenerCare of Your Softener Problem Cause Correction 3D.HELPFUL Hints Checklist To Help YOU Save MoneyTimer HF Code 4A.DIMENSIONS/SPECIFICATIONSService Tech Information 5A.TROUBLESHOOTINGWiring Schematic FaceplateAutomatic Electronic Diagnostics Service TECH. Information 5A.TROUBLESHOOTINGManual Initiated Electronics DIAG- Nostics Possible Defect CodeIndicator Valve Position TroubleshootingManual Advance Regeneration Check Disassembly 5B.ROTARY Valve ServiceAssembly Servicing the ValveService Cycle Service TECH. Information5C .. Water Flow Through the Softener Valve Fill CycleBrining and Brine Rinse Cycles 5C. Water Flow Through the Softener Valve5C. Water Flow Through the Softener Valve \ \Section KEY Part Description Number Kenmore Water SOFTENER, Model noInlet Outlet Grounding Clamps Brineassemblyvalve=P,,,IRPARTS KEY Part NO. Number Parts ListPage Page Sears

625.34867 specifications

The Kenmore 625.34867 is a compact, high-efficiency dehumidifier designed to improve indoor air quality in homes and small spaces. This versatile appliance proves to be a valuable addition for those struggling with excess moisture, mold, and mildew, particularly in areas such as basements, bathrooms, and laundry rooms.

One of the standout features of the Kenmore 625.34867 is its robust moisture removal capacity, which is capable of extracting up to 50 pints of water from the air each day. This makes it an ideal choice for medium to large-sized rooms, ensuring a comfortable atmosphere while effectively preventing the detrimental effects of humidity.

Equipped with a user-friendly digital control panel, the Kenmore 625.34867 allows for effortless operation and monitoring. Users can easily adjust the desired humidity level, which can be set between 35% and 85%, to suit their preferences. Additionally, the dehumidifier features a 24-hour timer and multiple fan speeds, offering flexibility in its operation to match varying conditions throughout the day.

One noteworthy technology integrated into this model is the built-in humidistat. This smart feature continuously monitors the room's humidity levels, automatically turning the unit on or off to maintain the set humidity, thereby conserving energy and ensuring optimal performance.

The Kenmore 625.34867 is also designed with optimal drainage solutions in mind. It includes a removable water tank with a large capacity, which makes emptying infrequent and straightforward. For added convenience, users can opt for continuous drainage via a standard garden hose, eliminating the need to manually empty the tank.

In terms of portability, this dehumidifier is equipped with durable caster wheels that allow for easy movement from room to room. The ergonomic top handle contributes to its ease of transport, making it simple to adapt it to different spaces as needed.

Finally, the Kenmore 625.34867 is designed with safety in mind. It features an automatic shut-off function that activates when the water tank is full, preventing overflow and potential water damage. Combined with its energy-efficient operation, this dehumidifier stands as a practical solution for maintaining a healthy indoor environment, free from excessive moisture and its associated issues.
Top Page Image Contents