Kenmore 625.348460 SET Water Hardness Number, SET Recharge Regeneration Time, SET ``CLEAN Feature

Page 7

SECTION 1

WATER SOFTENER START-UP

1C.PROGRAM THE TIMER

2.SET WATER HARDNESS NUMBER:

■ Press the SELECT button once to display 15 (flashing) and HARDNESS.

The grains per gallon (gpg) hardness of your water supply is on your water analysis report. Be sure to enter water test results on page 2, for future reference.

NOTE:

If your water supply contains iron, compensate for it by adding to the water hardness number. For example￿ assume your water is 15 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each 1 ppm of iron. In this example￿ you would use 25 for your hardness number.

 

15 gpg hardness

2 ppm iron x 5 = 10

+10

(times)

25 HARDNESS NUMBER

■ Press the UP/DOWN buttons to set your water hardness number in the display. The DOWN button moves the display to 1. The UP button moves the display to the highest setting (see maximum setting for your model in the specifications).

NOTE:

Each press of the UP/DOWN button changes the display by 1 between 1 and 25. Between 25 and the highest number, the display changes 5 at a time25, 30, 35, etc. Continuous pressure on the UP or DOWN button changes the display twice each second.

3.SET RECHARGE (REGENERATION) TIME:

■ Press the SELECT button once to display 2:00 AM (flashing) and RECHARGE TIME.

At the 2:00 AM RECHARGE TIME setting, the softener begins re; generation (see pages 11 and 12) at 2:00 AM, ending no later than

4:00 AM. This is a good time in most households because water is not being used (see AUTOMATIC BYPASS, page 13). If a different RECHARGE TIME setting would be better for your household, do the following.

■ Press the UP/DOWN buttons to set the desired RECHARGE starting hour. Be sure to observe the AM;PM as you did when setting the present time of day.

NOTE:

Each press of the UP/DOWN buttons changes the display 1 hour. Continuous pressure on the buttons changes the display twice each second.

Press the SELECT button once again, to return the present time (steady) of day and RECHARGE TONIGHT in the display.

4.SET ``CLEAN'' FEATURE:

 Press the SELECT button again. The display alternates between ``CLEAn￿￿, and ``OFF￿￿ (de; fault).

When set to ``CLEAn￿￿/``ON￿￿, a backwash is as; sured after every 500 gallons of water usage. Back; wash is described on page 12. This cleaning back; wash is in addition to the backwash during re; charge. If you have iron in the water supply, or higher amounts of sediments (sand, silt, dirt, etc.) you should set this feature to ON.

To set to ON, or to turn off if already on, press either the UP or DOWN button once. The length of this extra backwash is 1 minute (default time setting).

IF YOU NEED HELP PROGRAMMING THE TIMER, CALL TOLL FREE, NUMBER 1±800±426±9345. SEE PAGE 10 FOR OTHER FACE PLATE TIMER FEATURES.

IMPORTANT: Salt is used to recharge the mineral in your water softener...see page 9. Before shipping, the mineral is factory pretreated with salt. Before using water from this softener, be sure to do the sanitizing procedures and start a recharge (page 8), to flush salt from it.

7

Image 7
Contents Save this Manual Model noSears Installation Policy Sears Installation Warranty WarrantyFull ONE Year Warranty on Water Softener Full TEN Year Warranty Against LeaksSoftener Start UP Table of ContentsService Tech Information Repair PartsSection Water Softener START-UP Safety Guides± Valve Bypass Plastic Bypass Brass Bypass Water Heater SET Present Time of DAY Note Water Softener START-UP 1C.PROGRAM the TimerSET Water Hardness Number SET ``CLEAN FeatureSET Recharge Regeneration Time ADD Water Water Softener START-UP 1D. Sanitizing the Water SoftenerADD Salt Water Softener START-UP 1E. Fill the Storage Tank with SaltProgram Memory HOW Your Water Softener Works 2A.FACE Plate Timer FeaturesError Code Extra RechargeFill Backwash Brining Fast Rinse Brine Rinse ServiceWater Flow Through the Softener in Brining and Brine Rinse Electronics Automatic BypassPlease see page 9 for Salt Filling Directions Salt BridgeIron from the Resin BED Care of Your Softener 3D. Keeping the Water Softener CleanCovers Nozzle and VenturiDrain Water from the Softener Care of Your Softener 3D. Keep the Softener from FreezingProblem Cause Correction Water has Salty Timer SC Code SC21 Other Things to Know 4A.DIMENSIONS/SPECIFICATIONSBypass Valves Always Make These Initial Checks First Service TECH. Information 5A.TROUBLESHOOTINGManual Initiated Electronics Diag Nostics Automatic Electronic Diagnostics± ± Correct Switch Displays Valve Cycle StatusCycle Flow Rates Gallons PER MIN Manual Advance Regeneration CheckServicing the Valve Service TECH. Information 5B.ROTARY Valve ServiceDisassembly AssemblyFill Cycle Service CycleBrining and Brine Rinse Cycles Backwash and ``CLEAN CycleFast Rinse Cycle Service TECH. Information Sears Water Softener Tubing Assem. Incl. Key No Valve Assembly KEY Part Owners Manual