Kenmore 625.348460 Water Softener START-UP 1C.PROGRAM the Timer, SET Present Time of DAY Note

Page 6

SECTION 1

WATER SOFTENER START-UP

1C.PROGRAM THE TIMER

FIG. 1

When the transformer is plugged in, the model code SC21 shows in the face plate display for a few seconds, followed by a test number (example: S4.0). After the test number, 12:00 AM begins to flash. PRESENT TIME and RECHARGE TONIGHT show at the bottom of the display.

NOTE:

If SC - - flashes in the display, press the UP button (FIG. 1) until SC21 does show. Then press the SELECT button to display the flashing 12:00 AM. If other than SC21 shows, when the transformer is plugged in, please see page 17 to reset.

SOUND •BEEPER": A •beeper" sounds while pressing buttons for timer set:up. One beep signals a change in the face plate display. Repeated beeps means the timer will not accept a change from the button you have pressed, telling you to use another button. For example, while setting the hardness (step 2), the beeper sounds

repeatedly when the display reaches 1 using the DOWN button, or the highest hardness setting using the UP button.

1.SET PRESENT TIME OF DAY: NOTE:

If the words… PRESENT TIME do not show in the display, press the SELECT button (FIG. 1) until they do.

■ Press the UP/DOWN buttons to set the present time. Press UP to move the display ahead; press DOWN to move the time backward.

If the present time is between noon and midnight, be sure PM shows.

If the present time is between midnight and noon, be sure AM shows.

NOTE:

Each press of the UP/DOWN buttons changes the time by 1 minute. Holding the buttons in changes the time 32 minutes each second.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model no Save this ManualFull TEN Year Warranty Against Leaks WarrantyFull ONE Year Warranty on Water Softener Sears Installation Policy Sears Installation WarrantyRepair Parts Table of ContentsService Tech Information Softener Start UPWater Softener START-UP Safety Guides Section± Valve Bypass Plastic Bypass Brass Bypass Water Heater Water Softener START-UP 1C.PROGRAM the Timer SET Present Time of DAY NoteSET ``CLEAN Feature SET Water Hardness NumberSET Recharge Regeneration Time Water Softener START-UP 1D. Sanitizing the Water Softener ADD WaterWater Softener START-UP 1E. Fill the Storage Tank with Salt ADD SaltExtra Recharge HOW Your Water Softener Works 2A.FACE Plate Timer FeaturesError Code Program MemoryService Fill Backwash Brining Fast Rinse Brine RinseWater Flow Through the Softener in Brining and Brine Rinse Automatic Bypass ElectronicsSalt Bridge Please see page 9 for Salt Filling DirectionsNozzle and Venturi Care of Your Softener 3D. Keeping the Water Softener CleanCovers Iron from the Resin BEDCare of Your Softener 3D. Keep the Softener from Freezing Drain Water from the SoftenerProblem Cause Correction Water has Salty Other Things to Know 4A.DIMENSIONS/SPECIFICATIONS Timer SC Code SC21Bypass Valves Service TECH. Information 5A.TROUBLESHOOTING Always Make These Initial Checks FirstAutomatic Electronic Diagnostics Manual Initiated Electronics Diag NosticsCorrect Switch Displays Valve Cycle Status ± ±Manual Advance Regeneration Check Cycle Flow Rates Gallons PER MINAssembly Service TECH. Information 5B.ROTARY Valve ServiceDisassembly Servicing the ValveService Cycle Fill CycleBackwash and ``CLEAN Cycle Brining and Brine Rinse CyclesFast Rinse Cycle Service TECH. Information Sears Water Softener Tubing Assem. Incl. Key No Valve Assembly KEY Part Owners Manual
Top Page Image Contents