Kenmore 625.348460 owner manual Correct Switch Displays Valve Cycle Status, ± ±

Page 21

SECTION 5

SERVICE TECH. INFORMATION

5A.TROUBLESHOOTING

CORRECT

 

SWITCH

 

DISPLAYS

VALVE CYCLE STATUS

 

 

± ±

Valve in service, fill, brining,

backwash or fast rince position

 

 

 

±P

Valve rotating from one posi-

tion to another

 

 

 

C. While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is re: tained by the computer from the first time elec: trical power is applied to the face plate.

-- Press to display the number of days this face plate has had electrical power applied.

-- Press to display the number of regenera: tions initiated by this face plate since the SR code number was entered.

2. Press Select to advance to the following alternating displays.

TIME

This setting controls the length of the back: wash cycle (regular recharge backwash, and the CLEAN feature backwash if set to ON). A longer backwash is beneficial if supply water is dirty, or contains iron. The time is adjustable up to 5 minutes. Use the UP or DOWN button to set.

3. The next press of the SELECT button displays an AUTO RECHARGE screen.

For this model, the AUTO RECHARGE display must show. If anything other than AUTO shows, press a UP or DOWN button until it does show.

4. Press SELECT once again to display 12 hr, TIME.

TIME

 

TIME

At this setting, display times are shown in stan: dard clock time. If set to 24 hr, using the UP or DOWN button, display times will be in military time, 0100 (1:00 AM) to 0000 (midnight).

5. Press the SELECT button and hold 3 seconds until

. . .SC21 shows.

This code identifies the softener nominal capacity size. If the wrong number shows, the softener will operate on incorrect programming. Do the following as needed.

RETURN THE PRESENT TIME DISPLAY - Press the SELECT button.

CHANGE THE SR NUMBER - Press the UP or DOWN button to display correct number; press SELECT, and reset the timer.

NOTE:

If the face plate is left in a diagnostic display (or a flashing display when setting times or hardness), time of day automatically returns if a button is not pressed within 4 minutes.

RECHARGE

21

Image 21
Contents Save this Manual Model noFull ONE Year Warranty on Water Softener WarrantyFull TEN Year Warranty Against Leaks Sears Installation Policy Sears Installation WarrantyService Tech Information Table of ContentsRepair Parts Softener Start UPSection Water Softener START-UP Safety Guides± Valve Bypass Plastic Bypass Brass Bypass Water Heater SET Present Time of DAY Note Water Softener START-UP 1C.PROGRAM the TimerSET ``CLEAN Feature SET Water Hardness NumberSET Recharge Regeneration Time ADD Water Water Softener START-UP 1D. Sanitizing the Water SoftenerADD Salt Water Softener START-UP 1E. Fill the Storage Tank with SaltError Code HOW Your Water Softener Works 2A.FACE Plate Timer FeaturesExtra Recharge Program MemoryFill Backwash Brining Fast Rinse Brine Rinse ServiceWater Flow Through the Softener in Brining and Brine Rinse Electronics Automatic BypassPlease see page 9 for Salt Filling Directions Salt BridgeCovers Care of Your Softener 3D. Keeping the Water Softener CleanNozzle and Venturi Iron from the Resin BEDDrain Water from the Softener Care of Your Softener 3D. Keep the Softener from FreezingProblem Cause Correction Water has Salty Other Things to Know 4A.DIMENSIONS/SPECIFICATIONS Timer SC Code SC21Bypass Valves Always Make These Initial Checks First Service TECH. Information 5A.TROUBLESHOOTINGManual Initiated Electronics Diag Nostics Automatic Electronic Diagnostics± ± Correct Switch Displays Valve Cycle StatusCycle Flow Rates Gallons PER MIN Manual Advance Regeneration CheckDisassembly Service TECH. Information 5B.ROTARY Valve ServiceAssembly Servicing the ValveFill Cycle Service CycleBrining and Brine Rinse Cycles Backwash and ``CLEAN CycleFast Rinse Cycle Service TECH. Information Sears Water Softener Tubing Assem. Incl. Key No Valve Assembly KEY Part Owners Manual