Cisco Systems BC-23 manual Routing between VLANs Configuration Example, BC-70

Page 48

Configuring Transparent Bridging

Transparent and SRT Bridging Configuration Examples

Routing between VLANs Configuration Example

The following example shows the configuration for the topology shown in Figure 10. IP traffic is routed to and from switched VLAN domains 300, 400, and 600 to any other IP routing interface, as is IPX for VLANs 500 and 600. Because Fast Ethernet interfaces 2/1.20 and 3/1.40 are combined in bridge group 50, all other nonrouted traffic is bridged between these two subinterfaces.

interface FDDI 1/0.10

ip address 131.108.1.1 255.255.255.0 encap sde 300

!

interface FastEthernet 2/1.20.

ip address 171.69.2.2 255.255.255.0 encap isl 400

bridge-group 50

!

interface FastEthernet 2/1.30 ipx network 1000

encap isl 500

!

interface FastEthernet 3/1.40

ip address 198.92.3.3 255.255.255.0 ipx network 1001

encap isl 600 bridge-group 50

!

bridge 50 protocol ieee

Ethernet-to-FDDI Transparent Bridging Example

The following configuration example shows the configuration commands that enable transparent bridging between Ethernet and FDDI interfaces. Transparent bridging on an FDDI interface is allowed only on the CSC-C2FCIT interface card.

hostname tester

!

buffers small min-free 20 buffers middle min-free 10 buffers big min-free 5

!

no ip routing

!

interface ethernet 0

ip address 131.108.7.207 255.255.255.0 no ip route-cache

bridge-group 1

!

interface ethernet 2

ip address 131.108.7.208 255.255.255.0 no ip route-cache

bridge-group 1

!

interface Fddi 0

ip address 131.108.7.209 255.255.255.0 no ip route-cache

no keepalive bridge-group 1

!

bridge 1 protocol ieee

Cisco IOS Bridging and IBM Networking Configuration Guide

BC-70

Image 48
Contents Transparent and SRT Bridging BC-23Transparent Bridging Features Integrated Routing and BridgingBC-24 Bridge-Group Virtual Interface BC-25BC-26 Bridge-Group Virtual Interface in the RouterSRT Bridging Features Other ConsiderationsBC-27 Transparent and SRT Bridging Configuration Task List BC-28Configuring Transparent Bridging and SRT Bridging Assigning Each Network Interface to a Bridge GroupAs Ieee 802.1D standard, DEC or Vlan bridge BC-29Command Purpose Transparently Bridged VLANs for ISLChoosing the OUI for Ethernet Type II Frames BC-30BC-31 Transparently Bridged VLANs on an Fddi BackboneRouting between ISL VLANs BC-32Specifies a subinterface Subinterface with the VlanSame bridge group BC-33Configuring a Subscriber Bridge Group Configuring Transparent Bridging over WANsConfiguring Fast-Switched Transparent Bridging over ATM BC-34Configuring Transparent Bridging over DDR CommandDefining the Protocols to Bridge Specifying the Bridging ProtocolConfiguring Transparent Bridging over Frame Relay Determining Access for BridgingConfiguring an Interface for Bridging Fast-Switched Transparent BridgingConfiguring Transparent Bridging over Multiprotocol Lapb Bridging in a Frame Relay Network with No MulticastsBridging in a Frame Relay Network with Multicasts BC-37Configuring Transparent Bridging over Smds Configuring Transparent Bridging overSpecifies IP-to-X.121 mapping BC-38Configuring Concurrent Routing and Bridging Configuring Integrated Routing and BridgingSpecifies a protocol to be routed on a bridge group BC-39Configuring Interfaces Configuring the Bridge-Group Virtual InterfaceEnabling Integrated Routing and Bridging BC-40Configuring Protocols for Routing or Bridging BC-41Configuring Transparent Bridging Options Disabling IP RoutingBC-42 Configuring LAT Compression Enabling Autonomous BridgingBC-43 Establishing Multiple Spanning-Tree Domains Establishes a multiple spanning-tree domainBC-44 Configuring Bridge Table Aging Time Filtering Transparently Bridged PacketsForwarding Multicast Addresses BC-45Setting Filters at the MAC Layer BC-46Filters particular MAC-layer station addresses Filtering by Vendor CodeEthernet-ordered MAC address BC-47Filtering by Protocol Type TypeBC-48 Defining and Applying Extended Access Lists Configuration modeInterface BC-49BC-50 Filtering LAT Service Announcements Enabling LAT Group Code Service FilteringBC-51 Adjusting Spanning-Tree Parameters BC-52Setting the Bridge Priority Setting an Interface PriorityAdjusting Bpdu Intervals Assigning Path CostsAdjusting the Interval between Hello BPDUs Defining the Forward Delay IntervalDisabling the Spanning Tree on an Interface Defining the Maximum Idle IntervalBC-55 Configuring the PA-12E/2FE Port Adapter BC-56Monitoring and Maintaining the PA-12E/2FE Port Adapter BC-57BC-58 BC-59 Configuring Circuit Groups BC-60Configuring Constrained Multicast Flooding Configures a transmission pause intervalDistributes base load on the source MAC address only BC-61BC-62 Basic Bridging Example BC-63Concurrent Routing and Bridging Example BC-64Basic Integrated Routing and Bridging Example BC-65Complex Integrated Routing and Bridging Example BC-66Transparently Bridged VLANs Configuration Example BC-67Router One Router TwoBC-68 Router Three BC-69Routing between VLANs Configuration Example Ethernet-to-FDDI Transparent Bridging ExampleBC-70 Ethernet Bridging Example Router/Bridge in BuildingBC-71 SRT Bridging Example BC-72Configuration for the New York City Router Configuration for the Thule, Greenland RouterMulticast or Broadcast Packets Bridging Example BC-73Configuration for Bridge Transparent Bridging ExampleBC-74 Frame Relay Transparent Bridging Examples Bridging in a Frame Relay Network with No MulticastsBC-75 Transparent Bridging over Multiprotocol Lapb Example Bridging in a Frame Relay Network with MulticastsBC-76 Transparent Bridging over DDR Examples BC-77Fast-Switched Transparent Bridging over Smds Example Complex Transparent Bridging Network Topology ExampleBC-78 BC-79 Bridged Subnetworks with DomainsConfiguration for Router a BC-80Configuration for Router B Configuration for Router CConfiguration for Router D BC-81Fast Ethernet Subscriber Port, Frame Relay Trunk Example ATM Subscriber Ports, ATM Trunk ExampleBC-82 BC-83 Configuration of IRB for PA-12E/2FE Port Adapter Example BC-84

BC-23 specifications

Cisco Systems has long been a leader in the networking industry, and its BC-23 model exemplifies the company's commitment to innovation and performance. Aimed at enhancing business operations, the BC-23 is tailored for organizations looking for robust solutions that support their digital transformation efforts.

One of the standout features of the Cisco BC-23 is its advanced networking capabilities. It supports high-speed data transmission, enabling seamless communication across networks. With multi-gigabit Ethernet ports, the BC-23 facilitates faster data rates, accommodating the increasing bandwidth demands of modern applications. This feature is particularly beneficial for businesses that rely heavily on cloud services, video conferencing, and data-heavy applications.

Security is a top priority, and the Cisco BC-23 incorporates cutting-edge security measures. Integrated threat detection and prevention systems help safeguard sensitive data from cyber threats. Additionally, the device supports secure access protocols, ensuring that only authorized users can connect to the network. This multi-layered security approach not only protects the network infrastructure but also secures the integrity of the data being transmitted.

Another significant characteristic of the BC-23 is its support for software-defined networking (SDN). This technology allows businesses to manage their networks through centralized software applications, facilitating real-time adjustments and optimizations. The flexibility afforded by SDN is especially advantageous in dynamic environments where network demands can shift rapidly.

The Cisco BC-23 also offers enhanced management features, allowing IT teams to monitor network performance and analytics effectively. This visibility into network operations enables organizations to identify potential issues before they escalate, minimizing downtime and keeping business processes smooth.

Furthermore, the BC-23 is designed for scalability. As organizations grow, their networking needs evolve, and the BC-23 can easily adapt to these changes. Businesses can add additional devices and capabilities without the need for a complete overhaul of their existing infrastructure.

With its combination of speed, security, and scalability, the Cisco Systems BC-23 is an invaluable asset for modern businesses. It stands out not just as a networking device but as a comprehensive solution that meets the demands of today's fast-paced, technology-driven environment. As companies continue to leverage digital tools for growth and efficiency, the BC-23 will undoubtedly play a significant role in their success.