Cisco Systems BC-23 manual Enabling Autonomous Bridging, Configuring LAT Compression, BC-43

Page 21

Configuring Transparent Bridging

Transparent and SRT Bridging Configuration Task List

Command

no ip routing

ip routing

Purpose

Disables IP routing.

Enables IP routing.

All interfaces in the bridge group that are bridging IP should have the same IP address. However, if you have more than one bridge group, each bridge group should have its own IP address.

Enabling Autonomous Bridging

Normally, bridging takes place on the processor card at the interrupt level. When autonomous bridging is enabled, bridging takes place entirely on the ciscoBus2 controller, significantly improving performance. Autonomous bridging is a high-speed switching feature that allows bridged traffic to be forwarded and flooded on the ciscoBus2 controller between resident interfaces. If you are using the ciscoBus2 controller, you can maximize performance by enabling autonomous bridging on the following ciscoBus2 interfaces:

•MEC

•FCIT transparent

•HSSI HDLC

Although performance improvements will be seen most in the resident interfaces, the autonomous bridging feature can also be used in bridge groups that include interfaces that are not on the ciscoBus2 controller. These interfaces include the CTR, FCI with encapsulation bridging, and HSSI with encapsulation other than HDLC, such as X.25, Frame Relay, or SMDS, MCI, STR, or SBE16.

If you enable autonomous bridging for a bridge group that includes a combination of interfaces that are resident on the ciscoBus2 controller and some that are not, the ciscoBus2 controller forwards only packets between resident interfaces. Forwarding between nonresident and resident interfaces is done in either the fast or process paths. Flooding between resident interfaces is done by the ciscoBus2 controller. Flooding between nonresident interfaces is done conventionally. If a packet is forwarded from a nonresident to a resident interface, the packet is conventionally forwarded. If packets are flooded from a nonresident interface to a resident interface, the packet is autonomously flooded.

To enable autonomous bridging on a per-interface basis, use the following command in interface configuration mode:

Command

Purpose

 

 

bridge-group bridge-groupcbus-bridging

Enables autonomous bridging (if using the ciscoBus2 controller).

 

 

Note You can filter by MAC-layer address on an interface only when autonomous bridging is enabled on that interface. If any filters or priority queuing is configured, autonomous bridging is automatically disabled.

Configuring LAT Compression

The local-area transport (LAT) protocol used by Digital and Digital-compatible terminal servers is one of the common protocols that lacks a well-defined network layer (Layer 3) and so always must be bridged.

Cisco IOS Bridging and IBM Networking Configuration Guide

BC-43

Page 20 Page 22
Image 21
Page 20 Page 22
Contents BC-23 Transparent and SRT BridgingTransparent Bridging Features Integrated Routing and BridgingBC-24 BC-25 Bridge-Group Virtual InterfaceBridge-Group Virtual Interface in the Router BC-26SRT Bridging Features Other ConsiderationsBC-27 BC-28 Transparent and SRT Bridging Configuration Task ListAssigning Each Network Interface to a Bridge Group Configuring Transparent Bridging and SRT BridgingAs Ieee 802.1D standard, DEC or Vlan bridge BC-29Transparently Bridged VLANs for ISL Command PurposeChoosing the OUI for Ethernet Type II Frames BC-30Transparently Bridged VLANs on an Fddi Backbone BC-31BC-32 Routing between ISL VLANsSubinterface with the Vlan Specifies a subinterfaceSame bridge group BC-33Configuring Transparent Bridging over WANs Configuring a Subscriber Bridge GroupConfiguring Fast-Switched Transparent Bridging over ATM BC-34Command Configuring Transparent Bridging over DDRDefining the Protocols to Bridge Specifying the Bridging ProtocolDetermining Access for Bridging Configuring Transparent Bridging over Frame RelayConfiguring an Interface for Bridging Fast-Switched Transparent BridgingBridging in a Frame Relay Network with No Multicasts Configuring Transparent Bridging over Multiprotocol LapbBridging in a Frame Relay Network with Multicasts BC-37Configuring Transparent Bridging over Configuring Transparent Bridging over SmdsSpecifies IP-to-X.121 mapping BC-38Configuring Integrated Routing and Bridging Configuring Concurrent Routing and BridgingSpecifies a protocol to be routed on a bridge group BC-39Configuring the Bridge-Group Virtual Interface Configuring InterfacesEnabling Integrated Routing and Bridging BC-40BC-41 Configuring Protocols for Routing or BridgingConfiguring Transparent Bridging Options Disabling IP RoutingBC-42 Configuring LAT Compression Enabling Autonomous BridgingBC-43 Establishing Multiple Spanning-Tree Domains Establishes a multiple spanning-tree domainBC-44 Filtering Transparently Bridged Packets Configuring Bridge Table Aging TimeForwarding Multicast Addresses BC-45BC-46 Setting Filters at the MAC LayerFiltering by Vendor Code Filters particular MAC-layer station addressesEthernet-ordered MAC address BC-47Filtering by Protocol Type TypeBC-48 Configuration mode Defining and Applying Extended Access ListsInterface BC-49BC-50 Filtering LAT Service Announcements Enabling LAT Group Code Service FilteringBC-51 BC-52 Adjusting Spanning-Tree ParametersSetting an Interface Priority Setting the Bridge PriorityAdjusting Bpdu Intervals Assigning Path CostsDefining the Forward Delay Interval Adjusting the Interval between Hello BPDUsDisabling the Spanning Tree on an Interface Defining the Maximum Idle IntervalBC-55 BC-56 Configuring the PA-12E/2FE Port AdapterBC-57 Monitoring and Maintaining the PA-12E/2FE Port AdapterBC-58 BC-59 BC-60 Configuring Circuit GroupsConfigures a transmission pause interval Configuring Constrained Multicast FloodingDistributes base load on the source MAC address only BC-61BC-62 BC-63 Basic Bridging ExampleBC-64 Concurrent Routing and Bridging ExampleBC-65 Basic Integrated Routing and Bridging ExampleBC-66 Complex Integrated Routing and Bridging ExampleBC-67 Transparently Bridged VLANs Configuration ExampleRouter One Router TwoBC-68 BC-69 Router ThreeRouting between VLANs Configuration Example Ethernet-to-FDDI Transparent Bridging ExampleBC-70 Ethernet Bridging Example Router/Bridge in BuildingBC-71 BC-72 SRT Bridging ExampleConfiguration for the Thule, Greenland Router Configuration for the New York City RouterMulticast or Broadcast Packets Bridging Example BC-73Configuration for Bridge Transparent Bridging ExampleBC-74 Frame Relay Transparent Bridging Examples Bridging in a Frame Relay Network with No MulticastsBC-75 Transparent Bridging over Multiprotocol Lapb Example Bridging in a Frame Relay Network with MulticastsBC-76 BC-77 Transparent Bridging over DDR ExamplesFast-Switched Transparent Bridging over Smds Example Complex Transparent Bridging Network Topology ExampleBC-78 Bridged Subnetworks with Domains BC-79BC-80 Configuration for Router aConfiguration for Router C Configuration for Router BConfiguration for Router D BC-81Fast Ethernet Subscriber Port, Frame Relay Trunk Example ATM Subscriber Ports, ATM Trunk ExampleBC-82 BC-83 BC-84 Configuration of IRB for PA-12E/2FE Port Adapter Example

BC-23 specifications

Cisco Systems has long been a leader in the networking industry, and its BC-23 model exemplifies the company's commitment to innovation and performance. Aimed at enhancing business operations, the BC-23 is tailored for organizations looking for robust solutions that support their digital transformation efforts.

One of the standout features of the Cisco BC-23 is its advanced networking capabilities. It supports high-speed data transmission, enabling seamless communication across networks. With multi-gigabit Ethernet ports, the BC-23 facilitates faster data rates, accommodating the increasing bandwidth demands of modern applications. This feature is particularly beneficial for businesses that rely heavily on cloud services, video conferencing, and data-heavy applications.

Security is a top priority, and the Cisco BC-23 incorporates cutting-edge security measures. Integrated threat detection and prevention systems help safeguard sensitive data from cyber threats. Additionally, the device supports secure access protocols, ensuring that only authorized users can connect to the network. This multi-layered security approach not only protects the network infrastructure but also secures the integrity of the data being transmitted.

Another significant characteristic of the BC-23 is its support for software-defined networking (SDN). This technology allows businesses to manage their networks through centralized software applications, facilitating real-time adjustments and optimizations. The flexibility afforded by SDN is especially advantageous in dynamic environments where network demands can shift rapidly.

The Cisco BC-23 also offers enhanced management features, allowing IT teams to monitor network performance and analytics effectively. This visibility into network operations enables organizations to identify potential issues before they escalate, minimizing downtime and keeping business processes smooth.

Furthermore, the BC-23 is designed for scalability. As organizations grow, their networking needs evolve, and the BC-23 can easily adapt to these changes. Businesses can add additional devices and capabilities without the need for a complete overhaul of their existing infrastructure.

With its combination of speed, security, and scalability, the Cisco Systems BC-23 is an invaluable asset for modern businesses. It stands out not just as a networking device but as a comprehensive solution that meets the demands of today's fast-paced, technology-driven environment. As companies continue to leverage digital tools for growth and efficiency, the BC-23 will undoubtedly play a significant role in their success.
Top Page Image Contents