3.Push TRACK SKIP (13) to select the track you wish to play.
4.Press PLAY/PAUSE (16) and the unit will instantly play.
FLY CUE & CUE INSTRUCTIONS
The FLY CUE function lets you set cues “on the fly” with the press of a button. Press FLY CUE when the disc reaches the musical location you wish to make your cue or start point. The cue point is now programmed. Press CUE to return to the cue point. Press PLAY/PAUSE and the unit instantly starts from this
AND/OR
1.To
When the CD reaches the approximate musical spot you wish to make your cue, push PLAY/PAUSE so the unit enters the PAUSE mode (PLAY/PAUSE LED blinks). Move the SEARCH JOG WHEEL forward or in reverse until the precise spot at which you want CD play to begin is located. Push PLAY/PAUSE.
The cue point is now programmed. Press CUE to return to this
2.To fine tune your
3.If, however, the selected spot is not exactly where you want it, push the CUE button while the CD is playing and the disc will return to the
Locate the exact spot on the CD at which you want play to start by turning the SEARCH JOG WHEEL. Push PLAY/PAUSE to pre- program this new cue point. Press the CUE button to pause play at the new cue point. Push PLAY/PAUSE at any time and the unit will play from the
TROUBLESHOOTING
•If a disk will not play, check to see that it was loaded correctly (label side up) and that the CD unit is on a flat, level, stable surface. Check disc for dirt, scratches, spills, etc.
•If the disc spins but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver.
•If the CD skips, check it for dirt, oil or scratches. Do not assume that the CD player or laser is defective. Many CDs are recorded “out of spec” and skip on most or all CD players.
Before sending the unit to an authorized Gemini service technician, insert a disc that plays properly in another unit.
CDX-602
ROBO START INSTRUCTIONS
IN SINGLE-AUTO CUE MODE:
Use ROBO START (25) in
1.Engage
2.Press the ROBO START (25) button to activate ROBO START. Play will alternate between the two CD players. At the end of a track, the playing side pauses and the other CD deck plays a track. At the end of this track, the playing side pauses and the first CD deck resumes play.
IN CONTINUOUS MODE OR DURING NORMAL PLAY:
If you use the ROBO START function without
1.During normal play, set a cue point on the second CD deck.
2.Press the ROBO START button to activate ROBO START.
3.Press PLAY/PAUSE BUTTON on the playing side to start play from the cue point on the other CD deck.
NOTE: Pausing play in the middle of a track causes the other CD deck to play. When the new track ends, play resumes on the first CD player from the point at which it was paused.
SPECIFICATIONS CDX-601/CDX-602
GENERAL: |
|
Type | Compact Disc Player |
Disc Type | Standard Compact discs (12 cm & 8 cm) |
Time Display | Track Elapsed, Track Remain, or Total remain |
Variable Pitch | ± 12% Slider with Resume Switch |
Pitch Bend | ± 16% Maximum |
Instant Start | Within 0.03 seconds |
Track Selection | 1 to 99 Tracks |
Installation | 19" each |
Dimensions | 19” x 3.5” x 10” |
Weight Per Unit | 9.5 lbs. |
AUDIO SECTION: |
|
Quantization | 1 Bit Linear/Channel, 3 Beam Laser |
Oversampling Rate | 8 Times |
Sampling Frequency | 44.1 kHz |
Frequency Response | 20 Hz to 20 kHz |
Digital Output | IEC958 |
Total Harmonic Distortion | Less Than 0.05% |
Signal to Noise Ratio | 104 dB |
Dynamic Range | 98 dB |
Channel Separation | 90 dB (1 KHz) |
Output Level | 1.9 Volts R.M.S. |
Power Supply | AC 115/230V, 60/50 Hz |
Page 5